Biomechanical effect of interspinous process distraction height after lumbar fixation surgery: An in vitro model

Effect of two-level decompressive procedures on the biomechanics of the lumbo-sacral spine: an ex vivo study

Hemilaminectomy and laminectomy are decompressive procedures commonly used in case of lumbar spinal stenosis, which involve the removal of the posterior elements of the spine. These procedures may compromise the stability of the spine segment and create critical strains in the intervertebral discs. Thus, this study aimed to investigate if decompressive procedures could alter the biomechanics of the lumbar spine. The focus was on the changes in the range of motion and strain distribution of the discs after two-level hemilaminectomy and laminectomy. Twelve L2-S1 cadaver specimens were prepared and mechanically tested in flexion, extension and both left and right lateral bending, in the intact condition, after a two-level hemilaminectomy on L4 and L5 vertebrae, and a full laminectomy. The range of motion (ROM) of the entire segment was assessed in all the conditions and loading configurations. In addition, Digital Image Correlation was used to measure the strain distribution on the surface of each specimen during the mechanical tests, focusing on the disc between the two decompressed vertebrae and in the two adjacent discs. Hemilaminectomy did not significantly affect the ROM, nor the strain on the discs. Laminectomy significantly increased the ROM in flexion, compared to the intact state. Laminectomy significantly increased the tensile strains on both L3-L4 and L4-L5 disc (p = 0.028 and p = 0.014) in ipsilateral bending, and the compressive strains on L4-L5 intervertebral disc, in both ipsilateral and contralateral bending (p = 0.014 and p = 0.0066), with respect to the intact condition. In conclusion, this study found out that hemilaminectomy did not significantly impact the biomechanics of the lumbar spine. Conversely, after the full laminectomy, flexion significantly increased the range of motion and lateral bending was the most critical configuration for largest principal strain.

Posterior Midline Interspinal Fixation (PMIF) to Treat Persistent Severe Pain Due to Severe Compression Fracture of Thoracic Vertebral Body: A Case Report

Generally, severe persistent pain due to compression fractures of the lumbar and thoracic vertebral bodies in the elderly, that fail conservative measures are treated with vertebroplasty or kyphoplasty. However, in the case reported in this paper, the compression fracture was so severe, that accurate bone needle placement into the vertebral body was felt to be difficult. In addition, there was a high risk of extravasation of the cement into the surrounding structures or blow-up of the lateral wall of the vertebral body. Therefore, a simple operation of posterior midline interspinal fixation (PMIF) was performed. The patient was a 91-year-old lady with severe pain in the mid-thoracic spine due to a severe compression fracture of the seventh thoracic vertebral body that was totally flattened in its anterior part. The patient was neurologically intact. However, she had difficulty walking, because the pain was very severe in an upright position. She was treated with a back brace and oxycodone for six weeks without any benefit. Because she was a poor candidate for vertebroplasty or kyphoplasty, a PMIF system was implanted. Postoperatively, within two weeks, her pain score dropped from 9/10 to 0/10; and from two months onwards she was completely free of pain medications until her death from an unrelated cause, 18 months after the operation. This is the first reported case of PMIF for the treatment of pain due to vertebral body compression fracture in the elderly. PMIF is a simple minimally invasive procedure without compromising the facet or any bony structure. The risk of severe complications, therefore, is remote. The success in this single case, therefore, begs for further exploration of this method in the treatment of compression fractures in the elderly.

Multibody Models of the Thoracolumbar Spine: A Review on Applications, Limitations, and Challenges

Numerical models of the musculoskeletal system as investigative tools are an integral part of biomechanical and clinical research. While finite element modeling is primarily suitable for the examination of deformation states and internal stresses in flexible bodies, multibody modeling is based on the assumption of rigid bodies, that are connected via joints and flexible elements. This simplification allows the consideration of biomechanical systems from a holistic perspective and thus takes into account multiple influencing factors of mechanical loads. Being the source of major health issues worldwide, the human spine is subject to a variety of studies using these models to investigate and understand healthy and pathological biomechanics of the upper body. In this review, we summarize the current state-of-the-art literature on multibody models of the thoracolumbar spine and identify limitations and challenges related to current modeling approaches.

A Study to Compare the Efficacy of a Biodegradable Dynamic Fixation System With Titanium Devices in Posterior Spinal Fusion Between Articular Processes in a Canine Model

The objective of this study was to apply a biodegradable dynamic fixation system (BDFS) for lumbar fusion between articular processes and compare the fusion results and biomechanical changes with those of conventional rigid fixation. Twenty-four mongrel dogs were randomly assigned to 2 groups and subjected to either posterior lumbar fusion surgery with a BDFS or titanium rods (TRs) at the L5-L6 segments. Six animals in each group were sacrificed at 8 or 16 weeks. Fusion conditions were evaluated by computed tomography (CT), manual palpation, biomechanical tests, and histological analysis. Biomechanical tests were performed at the L4-7 (for range of motion (ROM)) and L5-6 (for fusion stiffness) segments. Histological examination was performed on organs, surrounding tissues, and the fused area. The magnesium alloy components maintained their initial shape 8 weeks after the operation, but the meshing teeth were almost completely degraded at 16 weeks. The biomechanical analysis revealed an increased lateral bending ROM at 8 weeks and axial torsion ROM at 16 weeks. The L4-5 extension-flexion ROMs in the BDFS group were 2.29 ± 0.86 deg and 3.17 ± 1.08 deg at 16 weeks, respectively, compared with 3.22 ± 0.56 deg and 5.55 ± 1.84 deg in TR group. However, both groups showed similar fusion results. The BDFS design is suitable, and its degradation in vivo is safe. The BDFS can be applied for posterior lumbar fusion between articular processes to complete the fusion well. Additionally, the BDFS can reduce the decline in lateral motion and hypermotion of the cranial adjacent segment in flexion-extension motion.

A novel dynamic fixation system with biodegradable components on lumbar fusion between articular processes in a canine model

The objective of this study was to design a novel dynamic fixation system with biodegradable components, apply it for lumbar fusion between articular processes and compare the fusion results and biomechanical changes to those of conventional rigid fixation. The novel dynamic fixation system was designed using a finite element model, stress distributions were compared and 24 mongrel dogs were randomly assigned to two groups and subjected to either posterior lumbar fusion surgery with a novel dynamic fixation system or titanium rods at the L5-L6 segments. Lumbar spines were assessed in both groups to detect radiographic, manual palpation and biomechanical changes. Histological examination was performed on organs and surrounding tissues. In the novel dynamic fixation system, stress was mainly distributed on the meshing teeth of the magnesium alloy spacer. The magnesium alloy components maintained their initial shape 8 weeks after the operation, but the meshing teeth were almost completely degraded at 16 weeks. The novel dynamic fixation system revealed an increased lateral bending range of motion at 8 weeks; however, both groups showed similar radiographic grades, fusion stiffness, manual palpation and histological results. The novel dynamic fixation system design is suitable, and its degradation in vivo is safe. The novel dynamic fixation system can be applied for posterior lumbar fusion between articular processes and complete the fusion like titanium rods.