Influence of posterior cruciate ligament tension on tibiofemoral and patellofemoral joint contact mechanics in cruciate-retaining total knee replacement: a combined musculoskeletal multibody and finite-element simulation

The influence of posterior cruciate ligament (PCL) tension on the clinical outcome of cruciate-retaining total knee replacement (CR-TKR) remains controversial. Various numerical approaches have been used to study this influence systematically, but the models used are limited by certain assumptions and simplifications. Therefore, the objective of this computational study was to develop a combined musculoskeletal multibody and finite-element simulation during a squat motion to 90° knee flexion with a CR-TKR design to overcome previous limitations regarding model inputs. In addition, different PCL tensions (tight, lax, resected) were modeled and the influence on tibiofemoral and resurfaced patellofemoral joint dynamics and contact stresses was evaluated. The effect of the PCL on knee joint dynamics and contact stresses was more pronounced at higher flexion angles. Tibiofemoral joint dynamics were influenced and a tight PCL induced increased posterior femoral translation during flexion. The maximum contact stress in the tibial insert increased from 20.6 MPa to 22.5 MPa for the resected and tightest PCL at 90° knee flexion. Patellofemoral joint dynamics were only slightly affected by PCL tension. However, the maximum contact stress in the patellar component decreased from 58.0 MPa to 53.7 MPa for the resected and tightest PCL at 90° knee flexion. The combination of musculoskeletal multibody and finite-element simulation is a sufficient method to comprehensively investigate knee joint dynamics and contact stresses in CR-TKR. The PCL tension after CR-TKR affects joint dynamics and contact stresses at the articulating implant surfaces.

Stress response envelopes of intact tibiofemoral joint and knee osteoarthritis

The purpose of this study was to determine stress envelopes for an intact tibiofemoral joint and to study how they vary with knee loading, external–internal rotation, varus–valgus rotation and cartilage degradation (osteoarthritis) using the finite element method. The envelopes were presented in terms of knee flexion angle. The maximum von Mises stress for all tibiofemoral joint components increased with increasing the axial compressive force magnitude. Menisci exhibited the highest magnitude of maximum von Mises stress as compared to the femoral and tibial cartilages. In a range of flexion angles between 0° and 100°, the medial meniscus exhibited the highest maximum von Mises stress than the lateral meniscus and the stress in medial meniscus tended to increase with increasing the flexion angle. External–internal and varus–valgus rotations changed the stress distribution: higher stress on lateral compartment but lower stress on medial compartment, and conversely. The internal rotation provided more extreme effect than the external rotation. For the knee osteoarthritis, cartilage degradation (early stage) caused maximum von Mises stress to increase on the intact menisci revealing that knee osteoarthritis could also cause meniscal tear. The late osteoarthritis caused the maximum von Mises stress to increase on the calcified cartilage and subchondral bone.

Influence of tibial bearing curvatures of a customised total knee implant on squatting motion and loads

A range of preliminary designs of customised total knee implants (CTKIs) was created by resurfacing the distal femur and applying different tibial bearing surface curvatures. These were then compared with a scaled off-the-shelf symmetric total knee implant (STKI). To evaluate the biomechanical performance, a dynamic knee simulation model was created with patient-specific muscle and ankle joint loads calculated from an OpenSim musculoskeletal model. Simulation results showed the transverse curvatures of the tibial bearing surface influenced femoral mediolateral translation, while its longitudinal curvatures affected femoral adduction. Compared to the STKI, the CTKIs could restore patient knee function.

Influence of patellar implantation on the patellofemoral joint of an anatomic customised total knee replacement implant: A case study

Few studies have been conducted to investigate kinematics and kinetics of the patellofemoral joint under physiological muscle forces and ankle joint loads. In this study, a preliminary design of a customised total knee implant was proposed and created. To compare the influences of different patella treatment scenarios, a dynamic knee simulation model was created with patient-specific muscle forces and ankle joint loads that are calculated from an OpenSim musculoskeletal model. The goal is to improve patellar implant-bone connection and restore patellofemoral joint mobility. Identical dynamic boundary conditions were applied on an unresurfaced patella and three different dome-shaped patellar implants. It was found that the unresurfaced patella and patellar implants resulted in different motions of patellar internal rotation and medial tilt. The size of the dome-shaped patellar implant affected the motion and loading of the patellofemoral joint. When the exposed patella bone was not fully covered by the patellar implant, the patella bone then contacted the femoral component during knee flexion. This would most likely lead to anterior knee pain and subsequent revision.

Biomechanical and Clinical Effect of Patient-Specific or Customized Knee Implants: A Review

(1) Background: Although knee arthroplasty or knee replacement is already an effective clinical treatment, it continues to undergo clinical and biomechanical improvements. For an increasing number of conditions, prosthesis based on an individual patient's anatomy is a promising treatment. The aims of this review were to evaluate the clinical and biomechanical efficacy of patient-specific knee prosthesis, explore its future direction, and summarize any published comparative studies. (2) Methods: We searched the PubMed, MEDLINE, Embase, and Scopus databases for articles published prior to February 1, 2020, with the keywords "customized knee prosthesis" and "patient-specific knee prosthesis". We excluded patient-specific instrument techniques. (3) Results: Fifty-seven articles met the inclusion criteria. In general, clinical improvement was greater with a patient-specific knee prosthesis than with a conventional knee prosthesis. In addition, patient-specific prosthesis showed improved biomechanical effect than conventional prosthesis. However, in one study, patient-specific unicompartmental knee arthroplasty showed a relatively high rate of aseptic loosening, particularly femoral component loosening, in the short- to medium-term follow-up. (4) Conclusions: A patient-specific prosthesis provides a more accurate resection and fit of components, yields significant postoperative improvements, and exhibits a high level of patient satisfaction over the short to medium term compared with a conventional prosthesis. However, the tibial insert design of the current patient-specific knee prosthesis does not follow the tibial plateau curvature.