Physicochemical Stability of Generic Thiotepa Concentrate and Ready-to-Administer Infusion Solutions for Conditioning Treatment

The objective of this study was to determine the physicochemical in-use stability of recently approved Thiotepa Riemser concentrate in the original vial and diluted ready-to-administer (RTA) infusion solutions in prefilled glucose 5% and 0.9% NaCl polyolefin bags. Thiotepa Riemser 10 mg/mL concentrates and infusion solutions (1 mg/mL, 2 mg/mL, 3 mg/mL) were prepared in triplicate and stored at 2-8 °C or 25 °C for 14 days. Thiotepa concentrations were determined using a stability-indicating RP-HPLC assay. In parallel, pH and osmolality were measured. Sub-visible particles were counted on day 0 and 14. Thiotepa Riemser concentrate was revealed to be stable for 14 days when stored at 2-8 °C, or for 24 h when stored at 25 °C. Thiotepa concentrations in infusion solutions stored at 2-8 °C remained above 95% of the initial concentrations for at least 14 days, regardless of the type of vehicle solution. When stored at 25 °C, thiotepa infusion solutions in glucose 5% proved to be physicochemically stable for 3 days (1 mg/mL), 5 days (2 mg/mL) or 7 days (3 mg/mL). Thiotepa infusion solutions in 0.9% NaCl remained physicochemically stable for 5 days (1 mg/mL) or 7 days (2 mg/mL, 3 mg/mL). At these points in time, the specification limit of ≤0.6% monochloro-adduct was fulfilled. In parallel, an elevation of the pH values was registered. Thiotepa concentrates and infusion solutions should be stored at 2-8 °C due to temperature-dependent physicochemical stability, and for microbiological reasons. Glucose 5% infusion solution is recommended as a diluent, and stability-improving nominal 2 mg/mL to 3 mg/mL thiotepa concentrations should be obtained.

Loading profile of topotecan into polyvinyl alcohol microspheres (DC Bead™) over a 7-day period

Purpose: DC Bead™ is successfully used for chemoembolization of various liver cancers. The purpose of this study was todetermine the loading capacity of the semi-synthetic topoisomerase-1 inhibitor topotecan into the DC Bead™ microspheres under static or agitated conditions and to assess the physicochemical stability over a period of 7 days.

Methods: Commercially available topotecan hydrochloride powder (Hycamtin®) was reconstituted with water for injection to yield a nominal concentration of 1 mg/mL topotecan. Polyvinyl alcohol (PVA)-based microspheres (DC Bead™, 300–500 µm, 2 mL/vial) were mixed with 4 mL of the reconstituted topotecan solution. Vials were stored light protected at room temperature under static or agitated conditions for 7 days ( n = 3, for each loading condition). At different time intervals, samples were taken from the excess solution and assayed via a stability-indicating HPLC assay. Drug-loading profiles were determined by measuring the remaining topotecan concentration in the excess solution.

Results: Under agitated conditions, topotecan was loaded into the microspheres rapidly after mixing. After 5 min 86.4 ± 0.1% of topotecan was loaded. Under static conditions, drug uptake was slower. Only 65.0 ± 0% were loaded after 5 min; 86.6 ± 0.1% drug uptake was achieved not until 1 h. Over a storage period of 7 days, topotecan remained loaded in the DC Bead™ microspheres at a level of >90%.

Conclusion: Drug uptake of 4 mg topotecan (1 mg/mL solution) into DC Beads™ was faster under agitated loading conditions. Nevertheless, after 1 h, ∼90% of topotecan was loaded into the DC Bead™ microspheres independent from the type of loading condition. The loading rate remained >90% over the observation period of 7 days and light-protected storage at room temperature. Loading and stability of topotecan-loaded DC Beads™ is suitable and convenient for preparation in a pharmacy-based cytotoxic preparation unit.