Scaphoid kinematics before and after scaphotrapeziotrapezoidal ligament section. Assessment by radiostereometric analysis and computed tomography in a cadaver study

A phantom and cadaveric study of radiostereometric analysis in posterior cervical and lumbar spinal fusion

BACKGROUND CONTEXT

Detecting pseudarthrosis following spinal fusion is important for accurate diagnosis and treatment. Current diagnostic measures hold certain drawbacks. Radiostereometric analysis (RSA) is a radiographic technique with the capability to measure intervertebral segment changes and may be a novel way of assessing fusion.

PURPOSE

The purpose of this work was to measure the accuracy and precision of RSA in instrumented posterior cervical and lumbar spinal fusion for measuring intervertebral movement. Further, to gain surgical practice with RSA in spine and determine optimal bead placements.

STUDY DESIGN

Artificial bone and cadaveric spine models were used to simulate a 3-level cervical (C3-C6) and a 2-level (L4-S1) lumbosacral posterior spinal fusion to analyze bead placements and to measure RSA accuracy and precision.

METHODS

Preliminary RSA bead placements were planned and measured in the artificial model. Secondary bead placements were adjusted slightly in the cadaveric model to consider additional fusion scenarios. Bead spread, detectability, and stability were measured to determine optimal placements. Translational and rotational precision of both models were measured. Accuracy was measured in the artificial spine model. Model-based RSA software was used for analysis.

RESULTS

Optimal bead placements were found to be throughout the lateral mass of C3-C6 and in the spinous process, transverse process, and within the screw canal of L4-S1. Detectability was high among all segments. Spread was greater in L4-S1 than C3-C6 due to bead collinearity along the transverse axis of the cervical vertebrae. Translational and rotational RSA accuracy in cervical and lumbosacral regions ranged between 0.005 to 0.014 mm and 0.058 to 0.208°. Translational and rotational precision measured in the phantom models ranged 0.017 to 0.131 mm and 0.058 to 0.394° in C3-C6, and 0.086 to 0.191 mm and 0.200 to 0.369° in L4-S1. Translational and rotational precision measured in the cadaveric models ranged 0.054 to 0.548 mm and 0.148 to 1.386° in C3-C6, and 0.068 to 0.164 mm and 0.100 to 0.270° in L4-S1.

CONCLUSIONS

RSA was found to be a feasible radiographic technique in C3-C6 and L4-S1 spinal fusion when measured in artificial and cadaveric models. Optimal bead placements were determined. Bead spread was shown to be better throughout the lumbar region than the cervical region due to anatomical size variations. RSA accuracy and precision were within acceptable RSA criteria.

CLINICAL SIGNIFICANCE

The results from this work contribute to the accuracy, precision, and bead placements for studying RSA in cervical and lumbar spinal fusions. This work may further support the development of clinical studies to assess spinal fusion by evaluating postoperative intervertebral movement using RSA.

Scapholunate kinematics after flexible anchor repair

The scapholunate joint is one of the keystones of the wrist kinematics, and its study is difficult due to the carpal bones size and the richness of surrounding ligaments. We propose a new method of quantitative assessment of scapholunate kinematics through bone motion tracking in order to investigate scapholunate ligament lesion as well as repair techniques. On 6 intact wrists, steel beads were inserted into the bones of interest to track their motions. Experimental set up allowed wrist flexion extension and radio-ulnar deviation motions. Low-dose bi-planar radiographs were performed each 10° of movement for different configurations: 1) intact wrist, 2) scapholunate ligament division, 3) repair by soft anchors at the posterior then 4) anterior part. Beads' 3D coordinates were computed at each position from biplanar X-Rays, allowing accurate registration of each wrist bone. The Monte Carlo sensitivity study showed accuracy between 0.2° and 1.6 ° for the scaphoid and the lunate in motions studied. The maximum flexion-extension range of motion of the scaphoid significantly decreased after anterior repair from 73° in injured wrist to 62.7°. The proposed protocol appears robust, and the tracking allowed to quantify the anchor's influence on the wrist kinematics.

Obtaining a Reliable Scaphotrapeziotrapezoid Radiograph: Pronation, Ulnar Deviation, and Thumb Abduction

A simple, reproducible technique for assessing the scaphotrapeziotrapezoid joint radiographically is described. In addition to its diagnostic value, the technique is simple to perform with a minifluoroscopy unit, allowing for image-guided injections of the scaphotrapeziotrapezoid joint.

Impact of scapholunate dissociation on human wrist kinematics

Neither the complex motions of the scapholunate joint, nor the kinematic changes that occur as a result of injury to it, are fully understood. We used electromagnetic tracking within affected bones to evaluate the physiologic motions in the planes of flexion and extension, and of radial and ulnar deviation of human cadaver wrists, before and after complete transection of the scapholunate ligaments. Despite individual variance between each wrist, we were able to establish a pattern in the changes that occurred after scapholunate ligament injury. During the motions examined, the scaphoid showed an increase in translational deviation in almost all motion axes. In contrast, the movement of the lunate seemed to be impaired, especially in radial-ulnar deviation.

μCT-generated carpal cartilage surfaces: validation of a technique

Computational models are increasingly being used for the analysis of kinematics and contact stresses in the wrist. To this point, however, the morphology of the carpal cartilage has been modeled simply, either with non-dimensional spring elements (in rigid body spring models) or via simple bone surface extrusions (e.g. for finite element models). In this work we describe an efficient method of generating high-resolution cartilage surfaces via micro-computed tomography (μCT) and registration to CT-generated bone surface models. The error associated with μCT imaging (at 10 μm) was 0.009 mm (95% confidence interval 0.007-0.012 mm ), or ~1.6% of the cartilage thickness. Registration error averaged 0.33±0.16 mm (97.5% confidence limit of ~0.55 mm in any one direction) and 2.42±1.56° (97.5% confidence limit of ~5.5° in any direction). The technique is immediately applicable to subject-specific models driven using kinematic data obtained through in vitro testing. However, the ultimate goal would be to generate a family of cartilage surfaces that could be scaled and/or morphed for application to models from live subjects and in vivo kinematic data.