Tuning of defects in ZnO nanorod arrays used in bulk heterojunction solar cells

High-Voltage, High-Current Electrical Switching Discharge Synthesis of ZnO Nanorods: A New Method toward Rapid and Highly Tunable Synthesis of Oxide Semiconductors in Open Air and Water for Optoelectronic Applications

A novel method of oxide semiconductor nanoparticle synthesis is proposed based on high-voltage, high-current electrical switching discharge (HVHC-ESD). Through a subsecond discharge in the HVHC-ESD method, we successfully synthesized zinc oxide (ZnO) nanorods. Crystallography and optical and electrical analyses approve the high crystal-quality and outstanding optoelectronic characteristics of our synthesized ZnO. The HVHC-ESD method enables the synthesis of ZnO nanorods with ultraviolet (UV) and visible emissions. To demonstrate the effectiveness of our prepared materials, we also fabricated two UV photodetectors based on the ZnO nanorods synthesized using the subsecond HVHC-ESD method. The UV-photodetector test under dark and UV light irradiation also had a promising result with a linear ohmic current-voltage output. In addition to the HVHC-ESD method's excellent tunability for ZnO properties, this method enables the rapid synthesis of ZnO nanorods in open air and water. The results demonstrate the preparation, highlight the synthesis of fine hexagonal-shaped nanorods under a second with controlled oxygen vacancies, and point defects for a wide range of applications in less than a second.

ZnO nanowires for solar cells: a comprehensive review

As an abundant and non-toxic wide band gap semiconductor with a high electron mobility, ZnO in the form of nanowires (NWs) has emerged as an important electron transporting material in a vast number of nanostructured solar cells. ZnO NWs are grown by low-cost chemical deposition techniques and their integration into solar cells presents, in principle, significant advantages including efficient optical absorption through light trapping phenomena and enhanced charge carrier separation and collection. However, they also raise some significant issues related to the control of the interface properties and to the technological integration. The present review is intended to report a detailed analysis of the state-of-the-art of all types of nanostructured solar cells integrating ZnO NWs, including extremely thin absorber solar cells, quantum dot solar cells, dye-sensitized solar cells, organic and hybrid solar cells, as well as halide perovskite-based solar cells.

Effect of reduced graphene oxide-hybridized ZnO thin films on the photoinactivation of Staphylococcus aureus and Salmonella enterica serovar Typhi

The immobilization of photocatalyst nanoparticles on a solid substrate is an important aspect for improved post-treatment separation and photocatalyst reactor design. In this study, we report the simple preparation of reduced graphene oxide (rGO)-hybridized zinc oxide (ZnO) thin films using a one-step electrochemical deposition, and investigated the effect of rGO-hybridization on the photoinactivation efficiency of ZnO thin films towards Staphylococcus aureus (S. aureus) and Salmonella enterica serovar Typhi (S. Typhi) as target bacterial pathogens. Field-emission scanning electron microscopy (FESEM) revealed the formation of geometric, hexagonal flakes of ZnO on the ITO glass substrate, as well as the incorporation of rGO with ZnO in the rGO/ZnO thin film. Raman spectroscopy indicated the successful incorporation of rGO with ZnO during the electrodeposition process. Photoluminescence (PL) spectroscopy indicates that rGO hybridization with ZnO increases the amount of oxygen vacancies, evidenced by the shift of visible PL peak at 650 to 500nm. The photoinactivation experiments showed that the thin films were able to reduce the bacterial cell density of Staph. aureus and S. Typhi from an initial concentration of approximately 10(8) to 10(3)CFU/mL within 15min. The rGO/ZnO thin film increased the photoinactivation rate for S. aureus (log[N/No]) from -5.1 (ZnO) to -5.9. In contrast, the application of rGO/ZnO thin film towards the photoinactivation of S. Typhi did not improve its photoinactivation rate, compared to the ZnO thin film. We may summarise that (1) rGO/ZnO was effective to accelerate the photoinactivation of S. aureus but showed no difference to improve the photoinactivation of S. Typhi, in comparison to the performance of ZnO thin films, and (2) the photoinactivation in the presence of ZnO and rGO/ZnO was by ROS damage to the extracellular wall.

UV-treated ZnO films for liquid crystal alignment

UV treatment has applied to modify the surface wettability of ZnO films for controlling the liquid crystal alignment.

Synthesis and modeling of uniform complex metal oxides by close-proximity atmospheric pressure chemical vapor deposition

A close-proximity atmospheric pressure chemical vapor deposition (AP-CVD) reactor is developed for synthesizing high quality multicomponent metal oxides for electronics. This combines the advantages of a mechanically controllable substrate-manifold spacing and vertical gas flows. As a result, our AP-CVD reactor can rapidly grow uniform crystalline films on a variety of substrate types at low temperatures without requiring plasma enhancements or low pressures. To demonstrate this, we take the zinc magnesium oxide (Zn(1-x)Mg(x)O) system as an example. By introducing the precursor gases vertically and uniformly to the substrate across the gas manifold, we show that films can be produced with only 3% variation in thickness over a 375 mm(2) deposition area. These thicknesses are significantly more uniform than for films from previous AP-CVD reactors. Our films are also compact, pinhole-free, and have a thickness that is linearly controllable by the number of oscillations of the substrate beneath the gas manifold. Using photoluminescence and X-ray diffraction measurements, we show that for Mg contents below 46 at. %, single phase Zn(1-x)Mg(x)O was produced. To further optimize the growth conditions, we developed a model relating the composition of a ternary oxide with the bubbling rates through the metal precursors. We fitted this model to the X-ray photoelectron spectroscopy measured compositions with an error of Δx = 0.0005. This model showed that the incorporation of Mg into ZnO can be maximized by using the maximum bubbling rate through the Mg precursor for each bubbling rate ratio. When applied to poly(3-hexylthiophene-2,5-diyl) hybrid solar cells, our films yielded an open-circuit voltage increase of over 100% by controlling the Mg content. Such films were deposited in short times (under 2 min over 4 cm(2)).

Tunable Surface Wettability of ZnO Nanoparticle Arrays for Controlling the Alignment of Liquid Crystals

The control of the liquid crystal (LC) alignment is very important for both academic research and practical applications. LC molecules aligned on the ZnO nanoparticle arrays (ZnO NPAs) are demonstrated and the pretilt angles of LCs can be controlled by using ZnO NPAs with different surface wettability. The wettability of ZnO NPAs fabricated by the solution-based hydrothermal method can be controlled by changing the annealing temperature of the as-prepared ZnO NPAs. The measurements of the energy-dispersive spectra and photoluminescence have shown that the chemical properties of ZnO NPAs have been changed with the annealing temperature. Our results show that the pretilt angle of LCs can be tuned continuously from ∼0 to ∼90° as the contact angle of water on ZnO NPAs changes from 33 to 108°.

Removal of organic contaminants from the surface of ZnO nanorods for organic/inorganic hybrid photovoltaics by using photocatalytic reaction

Properties of hybrid photovoltaics made of ZnO nanorods, which were deposited by solution process, and a polymer layer were improved by UV-treatment of the ZnO nanorods probably because organic contaminants remaining on the surface were photocatalytically decomposed.

Defect controlled water splitting characteristics of gold nanoparticle functionalized ZnO nanowire films

An ITO/FTO free AuNP functionalized ZnO NW photoanode in a dual role such as photo active centers for catalytic activity and an efficient transport medium for photo-generated charge carriers.

Liquid crystal alignment on zinc oxide nanowire arrays for LCDs applications

The zinc oxide (ZnO) nanowire arrays on the indium tin oxide (ITO) glass substrates were fabricated by using the two-step hydrothermal method. A high transmittance ~92% of ZnO nanowire arrays on ITO substrate in the visible region was obtained. It was observed that the liquid crystal (LC) directors were aligned vertically to the (ZnO) nanowire arrays. The properties of ZnO nanowire arrays as vertical liquid crystal (LC) alignment layers and their applications for hybrid-aligned nematic LC modes were investigated in this work.

Annealing effect and photovoltaic properties of nano-ZnS/textured p-Si heterojunction

The preparation and characterization of heterojunction solar cell with ZnS nanocrystals synthesized by chemical bath deposition method were studied in this work. The ZnS nanocrystals were characterized by X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM). Lower reflectance spectra were found as the annealing temperature of ZnS film increased on the textured p-Si substrate. It was found that the power conversion efficiency (PCE) of the AZO/ZnS/textured p-Si heterojunction solar cell with an annealing temperature of 250°C was η = 3.66%.

Nanostructured conformal hybrid solar cells: a promising architecture towards complete charge collection and light absorption

We introduce hybrid solar cells with an architecture consisting of an electrodeposited ZnO nanorod array (NRA) coated with a conformal thin layer (<50 nm) of organic polymer-fullerene blend and a quasi-conformal Ag top contact (Thin/NR). We have compared the performance of Thin/NR cells to conventional hybrid cells in which the same NRAs are completely filled with organic blend (Thick/NR). The Thin/NR design absorbs at least as much light as Thick/NR cells, while charge extraction is significantly enhanced due to the proximity of the electrodes, resulting in a higher current density per unit volume of blend and improved power conversion efficiency. The NRAs need not be periodic or aligned and hence can be made very simply.