Fixed-angle plates in patella fractures - a pilot cadaver study

Achieving Rapid Healing and Low Complication Rates in Patellar Fracture Fixation: The Benefits of Cerclage and Figure-of-Eight Configuration

Background and objective Patellar fractures account for around 1% of all fractures. Conservative treatment is advised in patients without any incompatibility of articular surfaces or those with intact extensor mechanisms. More than a 2-mm articular gap due to fracture warrants surgical intervention. Tension band wiring (TBW) is a commonly used practice for fixation, However, there is still controversy about its effectiveness and complications arising due to the hardware. Modification of this technique by using K-wires has been considered a method of choice, but this technique is associated with complications due to K-wires. The Pyrford technique is a method for patellar fracture fixation by circumferential cerclage and anterior TBW. We employed the figure-of-eight configuration over the circumferential wire. This study aimed to analyze the outcomes of TBW of the patella without K-wires by assessing the rate of complication and functional outcomes. Materials and methods A total of 38 patients with OTA 34C type, simple and comminuted type of patella fractures aged between 22 and 70 years were treated with circumferential cerclage and figure-of-eight TBW. All patients underwent patellar fixation with cerclage and through direct purchase of SS wire via quadriceps and patellar tendon. Patients were followed up for one to three years. We analyzed differences in the range of motion, fracture reduction, fracture healing time, Bostman score for knee function, and complications. Results The mean age of the patients was 45 years. After TBW without K-wires, fracture healing and functional outcomes were satisfactory according to patient feedback and clinocoradiological examinations. Of note, 35 out of 38 patients (92%) had gained up to 90 degrees of active flexion at the end of one week. One patient (2.42%) developed a superficial infection. All fractures had achieved union at the end of 16 weeks. Malunion or nonunion was not noted in any of the cases. There was no case of implant removal. The average Bostman score at the 12-month follow-up was 28.5 ±1.5. The incidence of complications due to K-wire was nullified. Conclusion Based on our findings, the described method leads to better functional outcomes, decreasing hardware-related complications, and can be used in simple as well as comminuted fractures. The fracture healing and functional outcomes and rate of complications were satisfactory.

Treating Inferior Pole Fracture of Patella with Hand Plating System: First Clinical Results

OBJECTIVE

Inferior pole fractures of patella are notorious fractures where it is difficult to obtain rigid internal fixation by conventional methods. The objective of the study was to introduce the Hand Plating System (HPS), which was a novel surgical technique for inferior pole fractures of patella, and to report the radiological and clinical outcomes following the application of the surgical technique.

METHODS

The study was designed as a retrospective cohort study. Between July 2017 and December 2018, 30 patients who were diagnosed with inferior pole fracture of the patella without additional orthopaedic injuries were enrolled in this case series. After X-ray and 3D-CT examinations, all patients underwent open reduction and internal fixation by HPS with or without supplementary cannulated screw and lag screw stabilization. The bony union time, final range of motion (ROM), Bostman score, visual analog scale (VAS), and complications were measured as the clinical outcomes under a minimum of 12 months of follow-up.

RESULTS

All of the operations went well with the mean operative time of 76.2 ± 15.3 min. Bony union achieved in all the cases at an average of 9.5 ± 1.4 weeks after surgery. There was no loss of reduction, fixative failure, or surgical implant removal during follow-up. The average range of motion 1 year postoperatively was 0°-123.3°. The mean Bostman Score at the last follow-up was 26.8 ± 2.1 with the satisfactory rate of 100%. The pain feeling during walking as measured by VAS averaged at 0.9 ± 1.3. No complications developed except for one case of poor incision healing, which healed eventually after surgical debridement.

CONCLUSIONS

HPS was demonstrated as a secure fixation and as a kind of tension band for inferior pole fractures of the patella. Satisfactory recovery of knee function and low complication rate, including no need for hardware removal, could be expected.

A Novel Technique for the Treatment of Inferior Pole Fractures of the Patella: A Preliminary Report

Objective

Most inferior pole fractures of the patella are comminuted. Therefore, an ideal treatment method has not been determined. We have presented a modified tension band fixation technique—the Krachow suturing, Nice knot combined with tension band fixation—and reported the results of the procedure.

Methods

A total of 16 inferior patellar pole fractures were treated at our institution between January 2019 and October 2020, 15 of which underwent treatment with the modified tension band fixation technique consisting of Krachow suturing with Nice knots combined with tension band fixation. The primary measures: knee motion, Bostman score, anterior knee pain, fixation failure.

Results

Bone union occurred at a mean of 9 weeks postoperatively (range: 8–13). There were no cases of postoperative anterior knee pain, refracture of the inferior patellar pole or wire breakage. The patients regained full ROM of the knee joint without functional deficits during follow‐up; the mean ROM was 128.46° ± 7.07° (range: 113.4°–137.8°). At the last follow‐up, all patients had a mean Bostman score of 28.40 ± 1.29 (range: 26–30), with an excellent score in 11 patients and a good score in four patients.

Conclusion

The modified tension band fixation technique for the treatment of inferior patellar pole fractures is a simple and easy‐to‐perform surgical technique that provides stable fixation and good functional results.

Suturing methods in prolapse surgery: a biomechanical analysis

INTRODUCTION

Pelvic organ prolapse is a common problem in urogynecological surgery. Abdominal and laparoscopic sacrocolpopexy is currently considered to be the gold standard of treatment. The main problem remains the anatomical point of fixation as well as how sutures are placed. We evaluated the biomechanical difference between an in-line ligament suture versus an orthogonal ligament suture and a single suture versus a continuous suture at the anterior longitudinal ligament in an in-vitro, sacrocolpopexy model.

METHODS

Biomechanical in-vitro testing was performed on human, non-embalmed, female cadaver pelvises. An Instron test frame (tensinometer) was used for load/ displacement analysis. The average patient age was 75 years. Ligament preparation yielded 15 ligaments available for testing. Recorded parameters were the ultimate load, failure displacement, and stiffness.

RESULTS

This in-vitro analysis of different suturing methods showed the difference between an orthogonal and an in-line approach to be the ultimate load. Orthogonal sutures displayed an ultimate load of 80 N while in-line suturing yielded only 57 N (p < 0.05). For the anterior longitudinal ligament, this study demonstrated that continuous suture is significantly superior to a single suture regarding failure displacement (p < 0.05).

CONCLUSION

We established baseline biomechanical parameters for the sacrospinous ligament and anterior longitudinal ligament. An orthogonal suture is superior to an in-line suture in an in-vitro model. A continuous suture is superior to a single suture at the anterior longitudinal ligament. Clinical trials might be able to evaluate whether any clinical significance can be established from these findings.

Novel Rim Plating Technique for Treatment of the Inferior Pole Fracture of the Patella

To aim of the present paper was to introduce a novel fixation technique for the treatment of inferior pole fracture of the patella. We performed a prospective observational study of consecutive cases of inferior pole fracture of the patella that were treated at our institution between January 2018 and June 2019. The patients include three men and one woman, with an average age of 47 years (range: 42–59 years). All patients were treated with the novel rim plating fixation technique for preserving the inferior pole of the patella. During the surgery, a 2.4 mm straight locking compression plate was contoured to adapt to the arc of the lower half of the patella as the rim plate. After reduction of the fracture, the rim plate was fixed to the proximal fragment of the patella through multiple locking screws, against the continuous pull of the patellar tendon. The rim plate encircles and constricts the inferior pole fragments, functioning as a compression and blocking construct. If necessary, an additional anterior tension band or mini locking plate can be used to further prevent anterior displacement of the inferior pole fragments. Under this rigid fixation, motion of the knee and full weight‐bearing were encouraged postoperatively. The patients were followed up monthly until 12 months after surgery. The time to achieve 90°pain‐free, full range of motion of the knee, and fracture healing, were recorded. Related complications were monitored, including infection, loss of reduction, fixation failure, anterior knee pain, and soft‐tissue irritation. The modified Cincinnati knee rating system was used for knee function assessment. The average operative time was 58.8 min (range: 52–63 min). The average blood loss was 59.8 mL (range: 45–71 mL). For all patients, pain‐free 90° range of motion was restored in 2–4 weeks, and the full range of motion was restored in 8–11 weeks. All patients achieved bone union in 6–9 weeks with no displacement of the fragments or breakage of the implant. No patient complained of anterior knee pain or soft‐tissue irritation. The modified Cincinnati score at 12‐month follow up demonstrated excellent outcomes in all four patients. The rim plating technique may be a feasible option for the treatment of the inferior pole fracture of the patella.

Outcomes after locked plating of displaced patella fractures: a prospective case series

PURPOSE

Tension band wiring remains a common treatment for patella fractures, but complication rates are high, with unsatisfactory results. The purpose of this observation study was to evaluate clinical results and complication rates of a novel patella locking plate fixation.

METHODS

Twenty patients (mean age, 59.2 ± 18 years) with displaced patella fractures were prospectively enrolled. Range of motion, knee scores (Tegner, Lysholm, Kujala), complications, and revision surgeries were assessed six weeks, six months, 12 months, and 24 months after surgery. Results were compared to the situation before trauma in regards to the time of follow-up using a paired sample t test.

RESULTS

According to the OTA classification, the fractures were classified as follows: one A1, four C1, six C2, and nine C3. Range of motion improved from 121° after six weeks to 140°, 141°, and 143° within the follow-up period. While the Tegner, Lysholm, and Kujala scores were 4.1/97/97, respectively, before trauma, they improved from 2.6/80/89 to 3.6/94/89, 3.7/95/94, and 4.1/97/97 within the follow-up period. Three patients had a complication (15%): one fracture dislocation, one reactive bursitis, and one renewed fracture. Four patients reported discomfort or anterior knee pain especially when kneeling on the implant.

CONCLUSIONS

The patella locking plate is a safe and effective treatment for patella fractures, including comminuted fractures. Function can be restored within six months after surgery, and the complication rate is low. Nonetheless, the implant can cause discomfort or anterior knee pain especially when kneeling, which can necessitate an implant removal.

Laparoscopic pectopexy: a follow-up cyclic biomechanical analysis determining time to functional stability

INTRODUCTION

Pectopexy, a laparoscopic method for prolapse surgery, showed promising results in previous transient testing by this group. It was shown that a single suture, yielding an ultimate load of 35 N, was equivalent to continuous suturing. This was demonstrated in an in vitro cadaver study. This transient data were used to establish an elastic stress-strain envelope. It was now possible to proceed to dynamic in vitro analysis of this surgical method to establish time to functional stability.

METHODS

Cyclic testing of this fixation method was performed on human female embalmed cadaver (cohort 1) and fresh, non-embalmed cadaver (cohort 2) pelvises. The testing envelope was 5-25 N at a speed of 1 mm/s. 100 load regulated cycles were applied.

RESULTS

100 cycles were completed with each model; no overall system failure occurred. Steady state, i.e., functional stability was reached after 14.5 (± 2.9) cycles for the embalmed group and after 19.1 (± 7.2) cycles for the non-embalmed group. This difference was statistically significant p = 0.00025.

CONCLUSION

This trial showed in an in vitro cyclic testing of the pectopexy method that functional stability may be achieved after no more than 19.1 cycles of load exposure. When remaining within the established load envelope of below 25 N, patients do not need to fear global fixation failure. Testing did demonstrate differences in non-embalmed and embalmed cadaver testing. Embalmed cadaver testing tends to underestimate time to steady state by 26.3%.

[Plate osteosynthesis after patellar fracture - the technique and initial results of a prospective study]

BACKGROUND

Tension band wiring after patellar fractures is related to a high number of implant-related complications (22-53 %). Revision surgery is necessary in 10-55 % of patients mostly with unsatisfactory results. The patella plate is an alternative treatment with the advantages of locked plating. The purpose of this study was to evaluate the first clinical prospective results and complications of this new implant.

MATERIALS AND METHODS

Between April 2013 and May 2015 all patients that were treated with locked plating for patella fractures were included in this prospective study. Patients were followed-up clinically after six weeks and six months.

RESULTS

Included in this study were 17 patients, 6 women and 11 men, with a mean age of 58 years (19-87). The knee range of motion was 120° after 6 weeks and improved to 138° after 6 months, corresponding to 84 % and 97 % of the range of motion of the healthy opposite knee. The Tegner activity scale increased from 2,5 to 3,5 (initial value: 4), the Lysholm score increased from 78 to 92 points (initial value: 97) and the Kujala score increased from 72 to 88 points (initial value: 96). Two complications occurred: one patient had a reactive bursitis prepatellaris and one patient sustained a loss of reduction.

CONCLUSION

Locked plating of patella fractures is a reliable alternative treatment with good functional outcomes and low complication rates.

Biomechanical comparison of pin and tension-band wire fixation with a prototype locking plate fixation in a transverse canine patellar fracture model

Objective: To compare a locking plate (LP) with pin and tension-band wire (pin/TBW) for fixation of mid-patellar transverse fractures.

Materials and methods: Cadaveric canine stifle joints from 10 adult mixed breed dogs (23–36 kg) were used. Mid-patellar transverse osteotomies were randomly stabilized (in pairs) with either pin/TBW or a prototype LP. Cyclic loads (1 Hz, 500 cycles) at 100% body weight (90°-135° stifle joint extension), were applied. Survival or failure of constructs was defined as <2 mm fracture gap distraction at 500 cycles, or ≥ 2 mm fracture gap distraction at the number of cycles sustained, respectively. Number of cycles at failure and distraction gap were compared with a paired Student’s t-test, and a survival analysis performed with a Mantel-Cox test. All constructs that survived cyclic testing were tested in single cycle load to failure (1.0 mm/sec; 110° stifle joint extension); yield strength was compared with a Wilcoxon rank sum test. Significance was set at p <0.05.

Results: All 10/10 LP and three out of 10 pin/ TBW fixations survived cyclic testing. Survival analysis, number of cycles at failure, and distraction gap all were significantly different between the two groups (p = 0.0011, p = 0.0013, and p <0.0001, respectively). Construct yield strength was not significantly different (p = 0.1273).

Conclusions: The failure mode with pin/TBW was consistently similar to failures observed clinically. The LP demonstrated consistent, reliable and stable fixation.

This work was performed at the Biomechanics Orthopedic Research Laboratory, Cummings School of Veterinary Medicine at Tufts University, North Grafton, MA, USA.

Functional outcome and economic burden of operative management of patellar fractures: the pivotal role of onerous implants

OBJECTIVES

The complication rate following operative treatment of patellar fractures remains high and is associated with a poor functional outcome. The primary goal of this study was to evaluate our functional outcome of patellar fracture osteosynthesis and define strategies to improve the outcome. The healthcare costs and utilization were calculated.

METHODS

All demographic, clinical, radiographic variables and hospital-related costs of 111 patients with 113 surgically treated patellar fractures between January 2005 and December 2014 were analyzed. Fractures were grouped as either simple or complex. Functional outcome was assessed using Knee Injury and Osteoarthritis Outcome Score (KOOS).

RESULTS

There were 67 simple fractures (59.3%) and 46 complex fractures (40.7%). The overall complication rate was 48.7%, including 19.5% implant-related complications. In 69 patients (61.1%), implants were removed. The outcome was rather poor, with considerable impairment in all KOOS subscales with the knee-related quality of life rated worst (median 62.5, IQR 37.5-81.25). Poor outcome correlated significantly with complex patellar fractures and extensive tension-band constructs.

CONCLUSIONS

The operative treatment of patellar fractures was associated with a high complication rate, functional impairment and reduced quality of life. Complex patellar fractures and extensive tension-band constructs were identified as the main determinants of poor outcome and increased economic burden due to higher reinterventions rates. Strategies to reduce complications and improve outcome should focus on less onerous implants.

Superior Outcomes After Operative Fixation of Patella Fractures Using a Novel Plating Technique: A Prospective Cohort Study

OBJECTIVE

The purpose of this prospective cohort study was to determine if a new patella fracture fixation construct resulted in improved outcomes compared with traditional tension band techniques.

DESIGN

Comparative cohort study.

SETTING

Academic level I trauma center.

PATIENTS/PARTICIPANTS

Patients with isolated, unilateral patellar fractures were enrolled prospectively. From 2012 to 2014, 33 patients underwent fixation with a novel plate construct that spans half of the patella circumference laterally and provides multiplanar fixation through a low-profile plate. A comparison cohort was drawn from 25 patients treated from 2008 to 2012, where treatment consisted of traditional tension band fixation techniques.

INTERVENTION

Surgical fixation of patella fractures was performed with either a tension band or novel plate construct.

MAIN OUTCOME MEASUREMENTS

Subjective postoperative clinical outcomes and objective functional and strength measurements were subsequently collected.

RESULTS

The 2 cohorts had similar baseline characteristics. Patients with the plate construct had clinically and statistically significantly superior Knee Outcome Survey Activities of Daily Living Scale (KOS-ADLS) scores throughout the study period (P < 0.001). Functional testing also demonstrated significant improvements in patients with plate constructs compared with tension band constructs at 12 months. Patients in the plate cohort had significantly increased thigh circumferences (P = 0.003) and decreased anterior knee pain (P < 0.0001) compared with the tension band cohort.

CONCLUSIONS

In this prospective cohort study, the use of a novel fixation construct with multiplanar and interfragmentary fixation and minimal disruption of patellar vascularity enables improved clinical outcomes and functional performance.

LEVEL OF EVIDENCE

Therapeutic Level II. See Instructions for Authors for a complete description of levels of evidence.

Inframammary Fold Reconstruction: A Biomechanical Analysis

Background:

Inframammary fold reconstruction has scarcely been evaluated in literature. No biomechanical analyses have been performed comparing different reconstructive methods. This evaluation compares the gold-standard suture reconstruction with an intrarib anchor system (Micro BioComposite SutureTak, Arthrex).

Methods:

Three analysis groups were compared including 8 Sawbone blocks, 22 embalmed cadaver, and 27 regular cadaver specimens (N = 57). Transient mechanical analysis was performed at 5 N/s using an Instron 5565 test frame.

Results:

Ultimate load favored the anchor system (compared with the gold-standard suture) by a factor of 9.8 (P < 0.0001) for the regular cadaver group and a factor of 1.7 (P < 0.038) for the embalmed cadaver group. A similar statistically significant benefit was shown for stiffness and load at 2-mm displacement.

Conclusions:

This analysis showed an anchor system to be the biomechanically superior fixation method in terms of ultimate load, fixation stiffness, and displacement at failure when compared with the gold-standard suture method in inframammary fold reconstruction. Because of superior stability in every aspect, an anchor system may be considered for inframammary fold reconstruction.

Laparoscopic Pectopexy: A Biomechanical Analysis

Introduction

Pectopexy, a laparoscopic method for prolapse surgery, showed promising results in recent literature. Further improving this approach by reducing surgical time may decrease complication rates and patient morbidity. Since laparoscopic suturing is a time consuming task, we propose a single suture /mesh ileo-pectineal ligament fixation as opposed to the commonly used continues approach.

Methods

Evaluation was performed on human non-embalmed, fresh cadaver pelves. A total of 33 trials was performed. Eight female pelves with an average age of 75, were used. This resulted in 16 available ligaments. Recorded parameters were ultimate load, displacement at failure and stiffness.

Results

The ultimate load for the mesh + simplified single “interrupted” suture (MIS) group was 35 (± 12) N and 48 (± 7) N for the mesh + continuous suture (MCS) group. There was no significant difference in the ultimate load between both groups (p> 0.05). This was also true for displacement at failure measured at 37 (± 12) mm and 36 (±5) mm respectively. There was also no significant difference in stiffness and failure modes.

Conclusion

Given the data above we must conclude that a continuous suture is not necessary in laparoscopic mesh / ileo-pectineal ligament fixation during pectopexy. Ultimate load and displacement at failure results clearly indicate that a single suture is not inferior to a continuous approach. The use of two single sutures may improve ligamental fixation. However, overall stability should not benefit since the surgical mesh remains the limiting factor.

Patellar Fractures

Purpose. To describe a new surgical procedure and its outcomes: osteosynthesis with high-resistance sutures, avoiding metallic implants. Open sky osteosynthesis with Kirschner and cerclage wiring is the current gold standard for patella fractures. Favorable functional outcomes have been observed, although implant removal is required in many cases due to the prominent wires under the skin. New implants have been sought after to minimize the need for second surgeries. Methods. Eight patients, aged between 25 and 61 years, with a minimum follow-up of 24 months, were included in the present study. The surgical procedure consists of open reduction followed by internal fixation performing 3 longitudinal tunnels crossing double high-resistance sutures within these tunnels and suturing among them. Next, an anterior cerclage with parenchymal suture was performed. Results. During follow-up, no secondary fracture displacement was observed. No patient required or requested implant removal. Functional outcomes were equitable to other surgical techniques. Conclusion. Despite the relatively small number of patients, osteosynthesis with high-resistance suture presents as an acceptable alternative within patella fracture treatment, being safe and with similar functional outcomes when compared with other techniques. Furthermore, no second surgeries for implant removal were required during the present study.

Plating of patella fractures: techniques and outcomes

Operative treatment of displaced patella fractures with tension band fixation remains the gold standard, but is associated with a significant rate of complications and symptomatic implants. Despite the evolution of tension band fixation to include cannulated screws, surprisingly little other development has been made to improve overall patient outcomes. In this article, we present the techniques and outcomes of patella plating for displaced patella fractures and patella nonunions.

An alternative patellar fracture fixation: a biomechanical study

OBJECTIVES

The purpose of this study is to compare open reduction and internal fixation of the patella with a locking plate and tension-band construct (PF) versus cannulated screws and tension-band fixation (SF). The hypothesis is that both constructs will have similar failure loads with simulated extension loading.

METHODS

Transverse patellar fractures were created in 10 cadaveric pairs of legs and were fixed with either PF or SF. Dual-energy X-ray Absorptiometry (DXA) scans of all calcanei measured bone mineral density (BMD). Using an MTS 810 servohydraulic testing machine, each leg cycled to full extension 10 times before loading to failure. A differential variable reluctance transducer measured the distraction of the patella. Data were analyzed using paired t test analysis and bivariate analysis for Pearson correlation coefficients.

RESULTS

There was no difference in the BMD between the PF and the SF groups (P = 0.367). No measurable differences occurred during the 10 cycles, and load at clinical failure was not significantly different between the 2 fixation groups (P = 0.38). Stiffness during the final loading cycle was significantly higher for the SF group (P = 0.008). Ultimate strength of fixation was significantly higher in PF group (P = 0.048). BMD was not correlated to the ultimate strength of SF (P = 0.112), but was correlated for PF (P = 0.025).

CONCLUSIONS

Based on our results, PF provides comparable strength to SF, and it seems to be a safe and effective alternative to the current gold standard.

Cyclic long-term loading of a bilateral fixed-angle plate in comparison with tension band wiring with K-wires or cannulated screws in transverse patella fractures

PURPOSE

A bilateral fixed-angle plate was biomechanically compared to the two currently preferred methods of osteosynthesis for transverse patella fractures. It was hypothesized that the new angle-stable implant would provide a secure and sustainable fracture fixation, superior to the established standard techniques.

METHODS

Twenty-one identical patellae made of polyurethane foam (Sawbones(®)), osteotomized to create a transverse two-part fracture, were fixed with modified anterior tension wiring, cannulated lag screws with anterior tension wiring or bilateral polyaxial 2.7-mm fixed-angle plates. The testing protocol consisted of 10,000 repetitive cycles using a non-destructive physiological load between 100 and 300 N at a simulated knee flexion of 60°.

RESULTS

All 21 Sawbone(®)-patellae sustained repetitive loading up to 10,000 cycles without failing. The anterior tension wire group displayed significant displacement of the fracture gap (0.7 ± 0.2 mm) during cyclic loading, while both lag screws with tension wiring and bilateral fixed-angle plates showed no fracture gap widening at all (p < 0.01).

CONCLUSION

The bilateral fixed-angle plate and cannulated lag screws with anterior tension wiring preserved a constantly reduced fracture gap over 10,000 tensile cycles in contrast to modified anterior tension wiring, which exhibited significant widening of the gap after initial loading. Results of in vitro testing indicate that bilateral fixed-angle plates provide sustainable fixation stability offering a promising new option in the treatment for transverse patella fractures.

Biomechanical studies on transverse olecranon and patellar fractures: a systematic review with the development of a new scoring method

INTRODUCTION

Several methods of transverse patellar and olecranon fixation have been described. This article compares biomechanical studies of various fixation methods using a newly developed scoring method.

SOURCE OF DATA

The databases PubMed, Web of Science, Science Direct, Google Scholar and Google were searched for relevant studies.

AREAS OF AGREEMENT

Fixation hardware failure remains a problem. Various materials and fixation techniques have been tested to provide an improved fixation of transverse olecranon and patellar fractures.

AREAS OF CONTROVERSY

The difference in biomechanical testing setup between the studies makes it hard to compare different fixation techniques.

GROWING POINTS

The newly developed grading method was proved to be unbiased and reliable; however, extra specifications need to be added at some criteria when adopting the scoring method.

AREAS TIMELY FOR DEVELOPING RESEARCH

Non-metallic constructs may provide an improvement to the currently used metallic tension band wiring technique; however, clinical research is required.