Interaction of removal Ethidium Bromide with Carbon Nanotube: Equilibrium and Isotherm studies

Preparation and application of zeolite-zinc oxide nano composite for nitrate removal from groundwater

Nanomaterial assisted removal of pollutants from water has got great attention. This study aimed to remove nitrate from groundwater using zeolite and zeolite-ZnO nanocomposite as synergetic effect. Zeolite-ZnO nanocomposite was prepared using the co-precipitation method. The Physico-chemical characteristics of the nanomaterials were determined using XRD, SEM, and FTIR. The results revealed that; Zeolite-ZnO nanocomposites with 13.12 nm particle size have successfully been loaded into the zeolite. In addition, its chemical composition was determined using AAS. The removal efficiency of nitrate from groundwater was studied using a batch experiment. The removal of nitrate was investigated as a function of adsorbent dose, pH, initial concentration of nitrate, contact time, and agitation speed. Moreover, the adsorption isotherm and kinetics were also determined. The results showed that the removal of nitrate was 92% at an optimum dose of 0.5 g, pH 5, initial nitrate concentration of 50 mg/L, the contact time of 1 h, and agitation speed of 160 rpm. The removal nitrate has been fitted well by the Langmuir isotherm model with correlation coefficients of R² = 0.988. Thus, indicating the applicability of monolayer coverage of the nitrate ion on the surface of the nanocomposite. The adsorption process follows the pseudo-second-order model with a correlation coefficient of R² = 0.997. The results of this work might find application in remediation of water by removing nitrate to meet the standards of water quality.

Comparison between removal of Ethidium bromide and eosin by synthesized manganese (II) doped zinc (II) sulphide nanoparticles: kinetic, isotherms and thermodynamic studies

The present work seeks to investigate the kinetics and thermodynamic studies of ethidium bromide (EtBr) and eosin adsorption onto the synthesized Manganese (II) doped Zinc (II) Sulphide nanoparticles. A convenient scheme of co-precipitation was used for the synthesis of Manganese (II) doped Zinc (II) Sulphide nanoparticles. The Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FESEM) and X-ray diffractogram (XRD) techniques were used for the characterization of synthesized nanoparticles. The adsorption study was undertaken in a systematic manner. Effects of different experimental parameters were studied using batch adsorption method. It was evident from the results that EtBr and eosin removal was inversely proportional to the concentration of initial dye and directly proportional to contact time and adsorbent used. To study the adsorption equilibrium three different isotherm models like Langmuir, Freundlich and Flory-Huggins were used. It was observed that adsorption data synced most successfully with Langmuir isotherm model as compared to Freundlich and Flory-Huggins isotherm model. To fit the investigational statistics, the kinetic models pseudo 1st order, pseudo 2nd order and intra particle diffusion were taken onto consideration. The maximum dye removal of 98.19% and 97.16% for EtBr and eosin, was observed during the synthesis of nanoparticles.

Preparation and Characterization of Graphene Oxide for Pb(II) and Zn(II) Ions Adsorption from Aqueous Solution: Experimental, Thermodynamic and Kinetic Study

A thermodynamic and kinetic study of the adsorption process of Zn (II) and Pb (II) ions from aqueous solution on the surface of graphene oxide (GO) to establish the mechanisms of adsorbate–adsorbent interaction on this surface. The effect of pH on the retention capacity was studied and adsorption isotherms were determined from aqueous solution of the ions; once the experimental data was obtained, the kinetic and thermodynamic study of the sorption process was carried out. The data were fitted to the Langmuir, Freundlich, Dubinin-Raduskevich and Temkin isotherm models. The results showed that Zn(II) and Pb(II) on the GO adsorbing surface fitted the Langmuir model with correlation coefficients (R²) of 0.996. Kinetic models studied showed that a pseudo-second-order model was followed and thermodynamically, the process was spontaneous according to the values of Gibbs free energy (ΔG^o). N₂ adsorption isotherms were determined and modeled with the NLDFT (nonlocal density functional theory) and QSDFT (quenched solid density functional theory) kernels.

Decomposition of DNA staining agent ethidium bromide by gamma irradiation: Conditions, kinetics, by-products, biological activity, and removal from wastewater

Ethidium Bromide (Eth-Br) is an intercalating agent commonly used in medical and biological laboratories as a DNA staining dye. Despite its popular use, aqueous solutions containing Eth-Br showed high toxicity, mutagenic capacity, and deactivate DNA transcription. In this study, the removal of Eth-Br from aqueous solutions by gamma irradiation has been fully investigated. Gamma irradiation was capable of achieving a near complete removal of Eth-Br in neutral and non-buffered aqueous solutions at an absorbed dose of 15 kGy. Various experimental conditions were studied and showed that the removal efficiency is not diminished. The addition of hydrogen peroxide (2 %) to the irradiated solutions reduced the D₅₀ and D₉₀ by 50 %. Modeling Eth-Br decomposition showed that the reaction followed pseudo first-order kinetics and reaches at least 90 % removal under all experimental conditions. TOC and HPLC measurements confirmed that Eth-Br is fully mineralized when the absorbed dose reaches 15 kGy. The biological activity of Eth-Br after irradiation treatment was investigated with synthetic DNA and natural DNA. The biological activity of Eth-Br was deactivated at an absorbed dose as low as 5 kGy. Toxicity measurement with E-coli bacteria also confirmed that the absorbed dose of 5 kGy was sufficient to remove Eth-Br toxicity.

Clean technology for synchronous sequestration of charged organic micro-pollutant onto microwave-assisted hybrid clay materials

The Sustainable Development Goal 6 (SDG #6) of the United Nations (UN) is hinged on the provision, availability, and sustainability of water for the global populace by 2030. In a bid to achieve this goal, the quest to seek for ubiquitous and low-cost adsorbents to treat effluents laden with industrial dyes, such as methylene blue (MB), is on the increase in recent years. Acute exposure of humans to (MB) dye causes cyanosis, necrosis, and jaundice and even leads to death. In this research, zinc-modified hybrid clay composite adsorbent (materials from kaolinite and biomass (crushed Carica papaya seeds and/or plantain peel)) was developed via microwave route. This adsorbent was characterized using field emission scanning electron microscopy (FE-SEM), Fourier transform infrared (FTIR) spectroscopy, energy-dispersive X-ray (EDX), and high-resolution transmission electron microscopy (HR-TEM). These characterization techniques confirmed the success achieved in doping hybrid clay with Zn. These adsorbents were used to sequester cationic dye (MB) from aqueous solutions and textile effluent under various experimental conditions. The adsorption and desorption data obtained were analyzed using various kinetic models, which are two-step kinetics, pseudo-first order, pseudo-second order, fractal kinetics, first-order desorption, second-order desorption, and modified statistical rate theory (MSRT) desorption models. Results showed that the adsorption of the dye occurred via several chemical interactions, while the latter models (for desorption) indicated that desorption occurred in two different desorption sites on the adsorbent surfaces, which showed that the adsorption of MB dye onto the adsorbents was stable without the emergence of any secondary pollution. Adsorption of MB was achieved within 15 min for aqueous solutions and 900 min for textile effluent, which is an improvement on previous results from other studies. The three adsorption-desorption cycles for MB uptake by the adsorbents showed that it is pragmatically applicable to treat textile effluents. Hence, low-cost composite adsorbents have a potential for the effective remediation of MB dye from textile effluents as this study confirmed.

Enhanced removal of ethidium bromide (EtBr) from aqueous solution using rectorite

Ethidium bromide (EtBr) is an intercalating agent commonly used as nucleic acid fluorescent tag in various techniques of life science field. It is considered as a serious biohazard due to its mutagenicity and carcinogenicity. As such, developing high efficiency and low cost materials as cleanup kits is in urgent need although many methods have already been developed. In this study we take use of the affinity of organic cations for clay minerals of high cation exchange capacity (CEC) and large specific surface area (SSA) and tested the removal of EtBr using rectorite, a type of clay mineral made of 1:1 regularly mixed layers of illite and montmorillonite. Our results showed that the uptake of Et⁺ on rectorite could be as high as 400 mmol/kg and the removal of Et⁺ was extremely fast. Desorption of inorganic cation Ca²⁺ and sorption of counterion Br^- revealed that cation exchange was the dominating mechanism of Et⁺ removal using rectorite. Thermal analyses revealed that the EtBr could be thermally destructed inside the interlayer of rectorite and the material could be thermally regenerated. Thus, clay minerals could have a great potential to be fabricated into cleanup kits for the removal of EtBr in case of spill.

New insights in the use of a strong cationic resin in dye adsorption

The adsorption of methyl orange (MO) in aqueous solution was evaluated using a cationic polymer (Amberlite IRA 402) in batch experiments under different experimental variables such as amount of resin, concentration of MO, optimum interaction time and pH. The maximum adsorption capacity of the resin was 161.3 mg g^-1 at pH 7.64 at 55 °C and using a contact time of 300 min, following the kinetics of the pseudo-first-order model in the adsorption process. The infinite solution volume model shows that the adsorption rate is controlled by the film diffusion process. In contrast, the chemical reaction is the decisive step of the adsorption rate when the unreacted core model is applied. A better fit to the Langmuir model was shown for equilibrium adsorption studies. From the thermodynamic study it was observed that the sorption capacity is facilitated when the temperature increases.

Efficient removal of ethidium bromide from aqueous solution by using DNA-loaded Fe3O4 nanoparticles

Ethidium bromide (EtBr) is widely used as DNA-staining dyes for the detection of nucleic acids in laboratories and known to be powerful mutagens and carcinogens. In the present paper, the removal of EtBr from aqueous solutions in a batch system using DNA-loaded Fe₃O₄ nanoparticles as a simple and efficient method was investigated. DNA was covalently loaded on the surface of Fe₃O₄ magnetic nanoparticles, which was confirmed by FT-IR analysis and zeta potential measurements. The morphology and crystal structure were characterized by SEM, TEM, and XRD. The influence factors on the removal efficiency such as initial EtBr concentration, contact time, adsorbent dose, pH, and temperature were also studied. The removal process of EtBr can be completed quickly within 1 min. The removal efficiency was more than 99% while the EtBr concentration was routinely used (0.5 mg L^-1) in biology laboratories and the dosages of nanoparticles were 1 g L^-1. For the different EtBr concentrations from 0.5 to 10 mg L^-1 in aqueous solution, the goal of optimized removal was achieved by adjusting the dosage of DNA-loaded Fe₃O₄ nanoparticles. The optimum pH was around 7 and the operational temperature from 4 to 35 °C was appropriate. Kinetic studies confirmed that the adsorption followed second-order reaction kinetics. Thermodynamic data revealed that the process was spontaneous and exothermic. The adsorption of EtBr on DNA-loaded Fe₃O₄ nanoparticles fitted well with the Freundlich isotherm model. These results indicated that DNA-loaded Fe₃O₄ nanoparticles are a promising adsorbent for highly efficient removal of EtBr from aqueous solution in practice.

Adsorption of ethidium bromide from aqueous solution onto nutraceutical industrial fennel seed spent: Kinetics and thermodynamics modeling studies

Dye pollutants from research laboratories are one of the major sources for environmental contamination. In the present study, a nutraceutical industrial fennel seed spent (NIFSS) was explored as potential adsorbent for removal of ethidium bromide (EtBr) from aqueous solution. The adsorbent was characterized by scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR). Through batch experiments, the operating variables like initial dye concentration, adsorbent dosage, temperature, contact time, and pH were optimized. Equilibrium data were analyzed using three number of two-parameter and six number of three-parameter isotherm models. The adsorption kinetics was studied using pseudo-first order and pseudo-second order. The diffusion effects were studied by film diffusion, Webber-Morris, and Dumwald-Wagner diffusion models. The thermodynamic parameters; change in enthalpy (ΔHº), entropy (ΔSº), and Gibbs free energy (ΔGº) of adsorption system were also determined and evaluated.

Magnetic Activated-ATP@Fe3O4 Nanocomposite as an Efficient Fenton-Like Heterogeneous Catalyst for Degradation of Ethidium Bromide

Magnetic attapulgite-Fe₃O₄ nanocomposites (ATP-Fe₃O₄) were prepared by coprecipitation of Fe₃O₄ on ATP. The composites were characterized by scanning electron microscopey, X-ray diffractometry, Brunauer-Emmett-Teller analysis, X-ray photoelectron spectroscopy, energy dispersive spectrometer and transmission electron microscopy. Surface characterization showed that Fe₃O₄ particles with an average size of approximately 15 nm were successfully embedded in matrix of ATP. The capacity of the Fe₃O₄-activated ATP (A-ATP@Fe₃O₄) composites for catalytic degradation of ethidium bromide (EtBr, 80 mg/L) at different pH values, hydrogen peroxide (H₂O₂) concentrations, temperatures, and catalyst dosages was investigated. EtBr degradation kinetics studies indicated that the pseudo-first-order kinetic constant was 2.445 min⁻¹ at T = 323 K and pH 2.0 with 30 mM H₂O₂, and 1.5 g/L of A-ATP@Fe₃O₄. Moreover, a regeneration study suggested that A-ATP@Fe₃O₄ maintained over 80% of its maximal EtBr degradation ability after five successive cycles. The effects of the iron concentrations and free radical scavengers on EtBr degradation were studied to reveal possible catalytic mechanisms of the A-ATP@Fe₃O₄ nanocomposites. Electron Paramagnetic Resonance revealed both hydroxyl (∙OH) and superoxide anion (∙O₂⁻) radicals were involved in EtBr degradation. Radical scavenging experiment suggested EtBr degradation was mainly ascribed to ∙OH radicals, which was generated by reaction between Fe²⁺ and H₂O₂ on the surface of A-ATP@Fe₃O₄.