Digital anatomical measurements and crucial bending areas of the fixation route along the inferior border of the arcuate line for pelvic and acetabular fractures

A retrospective comparison of the conventional versus three-dimensional printed model-assisted surgery in the treatment of acetabular fractures

OBJECTIVE

The aim of this study was to compare the clinical and radiological outcomes of the conventional versus individualized three-dimensional (3D) printing model-assisted pre-contoured plate fixation in the treatment of patients with acetabular fractures.

METHODS

The data from 18 consecutive patients who underwent surgery for the acetabular fractures were retrospectively analyzed. The patients were divided into two groups (9 in each): conventional and 3D printed model-assisted. The groups were then compared in terms of the duration of surgery, time of instrumentation, time of intraoperative fluoroscopy, and volume of blood loss. The quality of the fracture reduction was also evaluated postoperatively by radiography and computed tomography in both the groups. The quality of the fracture reduction was defined as good (<2 mm) or fair (>2 mm) based on the amount of displacement in the acetabulum.

RESULTS

The conventional group included 9 patients (9 males; mean age=41.7 years; age range=16-70) with a mean follow-up of 11.9 months (range=8-15); the 3D printed model-assisted group consisted of 9 patients (9 males; mean age=46.2 years; age range=30-66) with a mean follow-up of 10.33 months (range=7-17). The average duration of surgery, mean time of instrumentation, time of intraoperative fluoroscopy, and mean volume of blood loss were 180.5±9 minutes, 36.2±3.6 minutes, 6±1 times, and 403.3±52.7 mL in the 3D printed model-assisted group, and 220±15.6 minutes, 57.4±10.65 minutes, 10.4±2.2 times, and 606.6±52.7 mL in the conventional group, respectively. Procedurally, the average duration of surgery, mean time of instrumentation, and mean time of fluoroscopy were significantly shorter, and the mean volume of blood loss was significantly lower in the 3D printed model-assisted group (p<0.05). The quality of the fracture reduction was good in 7 patients (78%) in the conventional group and 8 patients (89%) in the 3D printed model-assisted group.

CONCLUSION

As compared with the conventional surgery, the 3D printing model-assisted pre-contoured plate fixation technique can improve the clinical and radiological outcomes of the acetabular fractures, with shorter surgery, instrumentation, intraoperative fluoroscopy times, and blood loss.

LEVEL OF EVIDENCE

Level III, Therapeutic study.

Morphology of the patellar tendon and its insertion sites using three-dimensional computed tomography: A cadaveric study

BACKGROUND

To clarify, with three-dimensional (3D) images, the morphological properties of the patellar tendon and both of its insertion sites.

METHODS

Thirty-two human cadaveric left knees were evaluated, and 3D computed tomography images were created. These images were used to analyse the morphology of both insertion sites of the patellar tendon, and the width, length and thickness of each region of the patellar tendon.

RESULTS

The insertion sites of the patellar tendon on the patellar and tibial sides were V-shaped and crescent-shaped, respectively, with the respective bony apexes located at 44.5 ± 2.2% (standard deviation) and 35.5 ± 2.8% of the tendon width from its medial edge. The proximal, central and distal widths of the patellar tendon were 29.9 ± 2.7 mm, 27.3 ± 2.5 mm and 25.0 ± 2.4 mm, respectively. The length of the patellar tendon was shortest at 40.6% ± 6.7% of the central width and gradually became longer toward both edges. The patellar tendon was thickest in the central portion of 40-75% and gradually became thinner toward both edges.

CONCLUSIONS

The morphological properties of the patellar tendon and its insertion sites on both the patellar and tibial sides were consistent. These findings indicate that the characteristics of the bone-patellar tendon-bone graft markedly depend on the location from which it is harvested, and that these characteristics contribute to predicting the length, width and shapes of the bone plugs of the graft when performing bone-patellar tendon-bone surgery.