Resistance to fracture of intraradicular posts made of biological materials

Fracture strength of 3-units fixed partial dentures fabricated with metal-ceramic, graphene doped PMMA and PMMA before and after ageing: An in-vitro study

OBJECTIVES

To evaluate the fracture strength and linear elongation at break of three-units fixed partial dentures (FPDs) fabricated with traditional and new materials for fixed prosthodontics before and after ageing.

METHODS

Sixty models of three-units FPDs were fabricated and cemented onto a Co-Cr model simulating the replacement of a maxillary second premolar. The samples were randomly divided into 3 groups: metal-ceramic (MCR), graphene-doped polymethylmethacrylate (PMMA-GR) and polymethylmethacrylate (PMMA). Half of the samples were directly subjected to fracture test, while the remaining half underwent an ageing process and then a fracture loading test using an electrodynamic testing machine. Fracture load and elongation at break values were taken and statistically analysed.

RESULTS

Significant differences were detected between the different materials (p<0.05). All groups showed a reduction of the fracture load and elongation at break values after ageing, but not statistically significant, except for PMMA group (p = 2.012e-19) (p = 3.8e-11).

CONCLUSIONS

MCR and PMMA-GR three-units FPDs showed higher fracture strength and lower elongation at break compared to PMMA. MCR and PMMA-GR had higher resistance to ageing processes compared to PMMA.

CLINICAL SIGNIFICANCE

PMMA-GR could be considered a material for long-term provisional restorations as its mechanical behaviour and ageing resistance are more like MCR than PMMA.

Comparison of the Fracture Resistance of Root-Canal-Treated Premolars Obturated With Dissimilar Materials: An In Vitro Study

Introduction The utilization of endodontic sealers is of paramount importance in ensuring the sustained efficacy and resilience of endodontic treatment. The primary objective of the research was to appraise and contrast the fracture resistance (FR) of three distinct categories of endodontic sealing materials that are frequently employed in the context of endodontic therapy. Materials and methods This research used an in vitro experimental design. Sixty single-rooted human teeth indicated for extraction were utilized according to established protocols. These teeth were then arbitrarily divided into four piles, one for each of the four possible sealants. All specimens were put through a standardized thermal cycling procedure to simulate clinical conditions after the root canals were obturated. The subsequent step involved testing the FR of each group by utilizing a universal testing machine up until failure. Any statistically significant difference in FR among the three sealing materials was identified through appropriate statistical analysis. Results Group 1, which utilized a particular sealing material, exhibited the highest mean fracture resistance, measuring at an impressive 1198.33 ± 321.4 Newtons (N). A post hoc analysis was done to see the exact differences between each group and statistically significant differences between Groups 1 and 2 (p<0.05), Groups 1 and 4 (p<0.05), and Groups 3 and 4 (p<0.001) were observed. Conclusion The FR of Group 1 specimens were noticeably greater than those of Group 2 and Group 4 while the FR of Group 3 specimens was more than that of the Group 4 specimens. This study provides important insights into the fracture resistance of various endodontic sealing materials.

Mechanical properties, biosafety, and shearing bonding strength of glass fiber-reinforced PEEK composites used as post-core materials

OBJECTIVE

To investigate the mechanical properties, biosafety, and shearing bonding strength of glass fibers-reinforced polyether-ether-ketone (PEEK-GF) for post-core materials.

METHODS

PEEK-GF composites with different glass fiber contents were prepared by extrusion injection and named PEEK-GF30, PEEK-GF40, and PEEK-GF50. Mechanical properties including flexural modulus, flexural strength, Vickers hardness, and compression strength were tested. The cross-sectional morphology was examined using scanning electron microscopy (SEM). Cytotoxicity was studied in vitro with Cell-counting kit-8 (CCK-8). Cell morphology was observed under a microscope. Cell growth on the composites' surfaces was analyzed with DAPI staining. The shearing bonding strength (SBS) of PEEK-GF50 was assessed after applying different pretreatments. Failure modes were evaluated by microscopy. SEM and contact-angle measurements were performed on the surfaces. Statistical analysis was conducted using one-way ANOVA (P < 0.05).

RESULTS

The mechanical properties of PEEK-GF composites improved with increased GF content. The PEEK-GF50 group exhibited flexural modulus (17.4 ± 0.5 GPa) close to that of dentin (18.6 GPa) and showed the highest flexural strength (350.0 ± 2.9 MPa), Vickers hardness (47.6 ± 4.5 HV), and compressive strength (264.0 ± 18.0 MPa). The SEM analysis demonstrated that the PEEK matrix combined well with glass fibers. The CCK-8 results confirmed the biosafety of all groups. DAPI staining indicated that cells were growing well on the composites' surface. The sample that was pretreated with sandblasting and plasma showed the highest SBS (16.0 ± 1.7 MPa).

SIGNIFICANCE

The PEEK-GF composites demonstrated excellent mechanical properties, biosafety, and SBS, and have great potential to serve as post-core materials.