Efficacy of Er:YAG laser irradiation for decontamination and its effect on biocompatibility of different titanium surfaces

Investigation of adhesion status of Candida species to the surface of resin materials produced at different angles with additive manufacturing

BACKGROUND

The aim of this study was to evaluate the adhesion of Candida glabrata, Candida albicans, Candida krusei, Candida parapsilosis and Candida tropicalis yeasts to disk-shaped resin materials produced from resin which used in the production of surgical guide with 0, 45 and 90-degrees printing orientations by Liquid Crystal Display additive manufacturing technology.

METHODS

Disk-shaped specimens were printed with surgical guide resin using the Liquid Crystal Display production technique in 3 printing orientations (0, 45 and 90-degrees). Surface roughness and contact angle values were evaluated. Real-Time PCR analysis was performed to evaluate Candida adhesion (C. glabrata, C. albicans, C. krusei, C. parapsilosis and C. tropicalis) Field emission scanning electron microscope (FESEM) images of the materials were obtained.

RESULTS

Specimens oriented at 45-degrees demonstrated higher surface roughness (P < .05) and lower contact angle values than other groups. No significant difference was found in the adhesion of C. glabrata, C. albicans, and C. parapsilosis among specimens printed at 0, 45, and 90-degrees orientations (P > .05). A higher proportion of C. krusei and C. tropicalis was found in the specimens printed at orientation degrees of 45 = 90 < 0 with statistical significance. Analyzing the adhesion of all Candida species reveals no statistical disparity among the printing orientations.

CONCLUSIONS

The surface roughness, contact angle, and adhesion of certain Candida species are affected by printing orientations. Hence, careful consideration of the printing orientation is crucial for fabricating products with desirable properties. In 45-degree production, roughness increases due to the layered production forming steps, whereas in 0-degree production, certain Candida species exhibit high adhesion due to the formation of porous structures. Consequently, considering these factors, it is advisable to opt for production at 90-degrees, while also considering other anticipated characteristics.

Er:YAG Laser and Hemolasertherapy: Bone and Gingiva Gain-Case Report

Background: Modern dentistry has increasingly valued conservative and biologically less invasive clinical practices, seeking to preserve the patients' tissues and natural dental elements. Most extractions in the dental clinic are preceded by periodontal disease that presents bone and gingival tissue loss, compromising the aesthetics as well as the support of dental elements. Objectives: The clinical approach in these cases often involves bone exertion followed by the successful installation of osseointegrated implants. Material and Methods: In this study, a case of extensive periodontal involvement and mobility of dental elements was carried out in a minimally invasive way, using the Er:YAG laser for periodontal decontamination and the hemolasertherapy technique to regenerate adjacent tissues, totaling nine weeks of treatment. Results: Clinical and radiographical improvement of tissue health and complete preservation of dental elements were observed. Conclusion: The patient underwent a follow-up appointment 2 years after the start of treatment when it was still possible to verify the stability of the clinical condition and the tissue gains obtained.

Influence of Er:YAG laser irradiation on surface properties of Ti-6Al-4V machined and hydroxyapatite coated

Surface treatment by laser irradiation can change the topography of titanium; however, little is known about the changes it causes when applied to other coatings. This study aimed to evaluate the influence of Er:YAG laser irradiation on the surface properties of titanium-aluminum-vanadium (Ti-6Al-4V) discs. Four Ti-6Al-4V surfaces were evaluated (n = 10): CON-control, machined without surface treatment; LT-machined + laser treatment; HA-hydroxyapatite coating; and LT-HA-hydroxyapatite coating + laser treatment. For the laser treatment, an Er:YAG laser with a wavelength of 2940 nm, a frequency of 10 Hz, and an energy density of 12.8 J/cm2 was used. The morphology of the coating was investigated by scanning electron microscopy and the surface composition by energy-dispersive X-ray spectroscopy. The influence of laser irradiation treatment on roughness and wettability was also evaluated. The Er:YAG laser promoted a significant reduction in the roughness Sa (p < 0.05) and in the contact angle (p = 0.002) of the LT surface compared to the CON surface. On the LT-HA surface, a significant decrease in roughness was observed only for the Rz parameter (p = 0.015) and an increase in the contact angle (p < 0.001) compared to the HA surface. The use of the Er:YAG laser with the evaluated parameters decreased the surface roughness and improved the wetting capacity of machined without surface treatment. In the group with hydroxyapatite coating, the laser influenced the surface roughness only for the parameter Rz and reduced their wetting capacity.