1
|
Zhu Y, Babazadeh-Naseri A, Brake MRW, Akin JE, Li G, Lewis VO, Fregly BJ. Evaluation of finite element modeling methods for predicting compression screw failure in a custom pelvic implant. Front Bioeng Biotechnol 2024; 12:1420870. [PMID: 39234264 PMCID: PMC11372789 DOI: 10.3389/fbioe.2024.1420870] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/21/2024] [Accepted: 08/05/2024] [Indexed: 09/06/2024] Open
Abstract
Introduction: Three-dimensional (3D)-printed custom pelvic implants have become a clinically viable option for patients undergoing pelvic cancer surgery with resection of the hip joint. However, increased clinical utilization has also necessitated improved implant durability, especially with regard to the compression screws used to secure the implant to remaining pelvic bone. This study evaluated six different finite element (FE) screw modeling methods for predicting compression screw pullout and fatigue failure in a custom pelvic implant secured to bone using nine compression screws. Methods: Three modeling methods (tied constraints (TIE), bolt load with constant force (BL-CF), and bolt load with constant length (BL-CL)) generated screw axial forces using functionality built into Abaqus FE software; while the remaining three modeling methods (isotropic pseudo-thermal field (ISO), orthotropic pseudo-thermal field (ORT), and equal-and-opposite force field (FOR)) generated screw axial forces using iterative physics-based relationships that can be implemented in any FE software. The ability of all six modeling methods to match specified screw pretension forces and predict screw pullout and fatigue failure was evaluated using an FE model of a custom pelvic implant with total hip replacement. The applied hip contact forces in the FE model were estimated at two locations in a gait cycle. For each of the nine screws in the custom implant FE model, likelihood of screw pullout failure was predicted using maximum screw axial force, while likelihood of screw fatigue failure was predicted using maximum von Mises stress. Results: The three iterative physics-based modeling methods and the non-iterative Abaqus BL-CL method produced nearly identical predictions for likelihood of screw pullout and fatigue failure, while the other two built-in Abaqus modeling methods yielded vastly different predictions. However, the Abaqus BL-CL method required the least computation time, largely because an iterative process was not needed to induce specified screw pretension forces. Of the three iterative methods, FOR required the fewest iterations and thus the least computation time. Discussion: These findings suggest that the BL-CL screw modeling method is the best option when Abaqus is used for predicting screw pullout and fatigue failure in custom pelvis prostheses, while the iterative physics-based FOR method is the best option if FE software other than Abaqus is used.
Collapse
Affiliation(s)
- Yuhui Zhu
- Department of Mechanical Engineering, Rice University, Houston, TX, United States
| | - Ata Babazadeh-Naseri
- Department of Mechanical Engineering, Rice University, Houston, TX, United States
| | - Matthew R W Brake
- Department of Mechanical Engineering, Rice University, Houston, TX, United States
| | - John E Akin
- Department of Mechanical Engineering, Rice University, Houston, TX, United States
| | - Geng Li
- Department of Mechanical Engineering, Rice University, Houston, TX, United States
| | - Valerae O Lewis
- Department of Orthopedic Oncology, University of Texas MD Anderson Cancer Center, Houston, TX, United States
| | - Benjamin J Fregly
- Department of Mechanical Engineering, Rice University, Houston, TX, United States
| |
Collapse
|
2
|
Li Z, Luo Y, Lu M, Wang Y, Gong T, He X, Hu X, Long J, Zhou Y, Min L, Tu C. Biomimetic design and clinical application of Ti-6Al-4V lattice hemipelvis prosthesis for pelvic reconstruction. J Orthop Surg Res 2024; 19:210. [PMID: 38561755 PMCID: PMC10983619 DOI: 10.1186/s13018-024-04672-5] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 01/04/2024] [Accepted: 03/13/2024] [Indexed: 04/04/2024] Open
Abstract
OBJECTIVE This study aims to biomimetic design a new 3D-printed lattice hemipelvis prosthesis and evaluate its clinical efficiency for pelvic reconstruction following tumor resection, focusing on feasibility, osseointegration, and patient outcomes. METHODS From May 2020 to October 2021, twelve patients with pelvic tumors underwent tumor resection and subsequently received 3D-printed lattice hemipelvis prostheses for pelvic reconstruction. The prosthesis was strategically incorporated with lattice structures and solid to optimize mechanical performance and osseointegration. The pore size and porosity were analyzed. Patient outcomes were assessed through a combination of clinical and radiological evaluations. RESULTS Multiple pore sizes were observed in irregular porous structures, with a wide distribution range (approximately 300-900 μm). The average follow-up of 34.7 months, ranging 26 from to 43 months. One patient with Ewing sarcoma died of pulmonary metastasis 33 months after surgery while others were alive at the last follow-up. Postoperative radiographs showed that the prosthesis's position was consistent with the preoperative planning. T-SMART images showed that the host bone was in close and tight contact with the prosthesis with no gaps at the interface. The average MSTS score was 21 at the last follow-up, ranging from 18 to 24. There was no complication requiring revision surgery or removal of the 3D-printed hemipelvis prosthesis, such as infection, screw breakage, and prosthesis loosening. CONCLUSION The newly designed 3D-printed lattice hemipelvis prosthesis created multiple pore sizes with a wide distribution range and resulted in good osteointegration and favorable limb function.
Collapse
Affiliation(s)
- Zhuangzhuang Li
- Department of Orthopedics and Orthopaedic Research Institute, West China Hospital, Sichuan University, Chengdu, Sichuan, 610041, People's Republic of China
- Model Worker and Craftsman Talent Innovation Workshop of Sichuan Province, No. 37 Guoxue Road, Chengdu, People's Republic of China
| | - Yi Luo
- Department of Orthopedics and Orthopaedic Research Institute, West China Hospital, Sichuan University, Chengdu, Sichuan, 610041, People's Republic of China
- Model Worker and Craftsman Talent Innovation Workshop of Sichuan Province, No. 37 Guoxue Road, Chengdu, People's Republic of China
| | - Minxun Lu
- Department of Orthopedics and Orthopaedic Research Institute, West China Hospital, Sichuan University, Chengdu, Sichuan, 610041, People's Republic of China
- Model Worker and Craftsman Talent Innovation Workshop of Sichuan Province, No. 37 Guoxue Road, Chengdu, People's Republic of China
| | - Yitian Wang
- Department of Orthopedics and Orthopaedic Research Institute, West China Hospital, Sichuan University, Chengdu, Sichuan, 610041, People's Republic of China
- Model Worker and Craftsman Talent Innovation Workshop of Sichuan Province, No. 37 Guoxue Road, Chengdu, People's Republic of China
| | - Taojun Gong
- Department of Orthopedics and Orthopaedic Research Institute, West China Hospital, Sichuan University, Chengdu, Sichuan, 610041, People's Republic of China
- Model Worker and Craftsman Talent Innovation Workshop of Sichuan Province, No. 37 Guoxue Road, Chengdu, People's Republic of China
| | - Xuanhong He
- Department of Orthopedics and Orthopaedic Research Institute, West China Hospital, Sichuan University, Chengdu, Sichuan, 610041, People's Republic of China
- Model Worker and Craftsman Talent Innovation Workshop of Sichuan Province, No. 37 Guoxue Road, Chengdu, People's Republic of China
| | - Xin Hu
- Department of Orthopedics and Orthopaedic Research Institute, West China Hospital, Sichuan University, Chengdu, Sichuan, 610041, People's Republic of China
- Model Worker and Craftsman Talent Innovation Workshop of Sichuan Province, No. 37 Guoxue Road, Chengdu, People's Republic of China
| | - Jingjunjiao Long
- Department of Orthopedics and Orthopaedic Research Institute, West China Hospital, Sichuan University, Chengdu, Sichuan, 610041, People's Republic of China
- Model Worker and Craftsman Talent Innovation Workshop of Sichuan Province, No. 37 Guoxue Road, Chengdu, People's Republic of China
| | - Yong Zhou
- Department of Orthopedics and Orthopaedic Research Institute, West China Hospital, Sichuan University, Chengdu, Sichuan, 610041, People's Republic of China
- Model Worker and Craftsman Talent Innovation Workshop of Sichuan Province, No. 37 Guoxue Road, Chengdu, People's Republic of China
| | - Li Min
- Department of Orthopedics and Orthopaedic Research Institute, West China Hospital, Sichuan University, Chengdu, Sichuan, 610041, People's Republic of China.
- Model Worker and Craftsman Talent Innovation Workshop of Sichuan Province, No. 37 Guoxue Road, Chengdu, People's Republic of China.
| | - Chongqi Tu
- Department of Orthopedics and Orthopaedic Research Institute, West China Hospital, Sichuan University, Chengdu, Sichuan, 610041, People's Republic of China.
- Model Worker and Craftsman Talent Innovation Workshop of Sichuan Province, No. 37 Guoxue Road, Chengdu, People's Republic of China.
| |
Collapse
|
3
|
Oyem PC, Burke ZD, Mesko NW, Nystrom LM. Custom three-dimensional printed implants for reconstruction of oncologic pelvic defects. J Surg Oncol 2024; 129:424-435. [PMID: 37754672 DOI: 10.1002/jso.27465] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/13/2023] [Revised: 09/12/2023] [Accepted: 09/18/2023] [Indexed: 09/28/2023]
Abstract
The use of three-dimensional printed implants in the field of orthopedic surgery has become increasingly popular and has potentiated hip reconstruction in the setting of oncologic resections of the pelvis and acetabulum. In this review, we examine and discuss the indications and technical considerations for custom implant reconstruction of pelvic defects.
Collapse
Affiliation(s)
- Precious C Oyem
- Cleveland Clinic, Lerner College of Medicine of Case Western University, Cleveland, Ohio, USA
- Department of Orthopaedic Surgery, Cleveland Clinic, Cleveland, Ohio, USA
| | - Zachary D Burke
- Department of Orthopaedic Surgery, Cleveland Clinic, Cleveland, Ohio, USA
| | - Nathan W Mesko
- Department of Orthopaedic Surgery, Cleveland Clinic, Cleveland, Ohio, USA
| | - Lukas M Nystrom
- Department of Orthopaedic Surgery, Cleveland Clinic, Cleveland, Ohio, USA
| |
Collapse
|
4
|
Babazadeh-Naseri A, Li G, Shourijeh MS, Akin JE, Higgs Iii CF, Fregly BJ, Dunbar NJ. Stress-shielding resistant design of custom pelvic prostheses using lattice-based topology optimization. Med Eng Phys 2023; 121:104012. [PMID: 37985018 DOI: 10.1016/j.medengphy.2023.104012] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/30/2022] [Revised: 05/20/2023] [Accepted: 06/22/2023] [Indexed: 11/22/2023]
Abstract
Endoprosthetic reconstruction of the pelvic bone using 3D-printed, custom-made implants has delivered early load-bearing ability and good functional outcomes in the short term to individuals with pelvic sarcoma. However, excessive stress-shielding and subsequent resorption of peri‑prosthetic bone can imperil the long-term stability of such implants. To evaluate the stress-shielding performance of pelvic prostheses, we developed a sequential modeling scheme using subject-specific finite element models of the pelvic bone-implant complex and personalized neuromusculoskeletal models for pre- and post-surgery walking. A new topology optimization approach is introduced for the stress-shielding resistant (SSR) design of custom pelvic prostheses, which uses 3D-printable porous lattice structures. The SSR optimization was applied to a typical pelvic prosthesis to reconstruct a type II+III bone resection. The stress-shielding performance of the optimized implant based on the SSR approach was compared against the conventional optimization. The volume of the peri‑prosthetic bone predicted to undergo resorption post-surgery decreased from 44 to 18%. This improvement in stress-shielding resistance was achieved without compromising the structural integrity of the prosthesis. The SSR design approach has the potential to improve the long-term stability of custom-made pelvic prostheses.
Collapse
Affiliation(s)
| | - Geng Li
- Department of Mechanical Engineering, Rice University, Houston, TX 77005, USA
| | | | - John E Akin
- Department of Mechanical Engineering, Rice University, Houston, TX 77005, USA
| | - C Fred Higgs Iii
- Department of Mechanical Engineering, Rice University, Houston, TX 77005, USA
| | - Benjamin J Fregly
- Department of Mechanical Engineering, Rice University, Houston, TX 77005, USA
| | - Nicholas J Dunbar
- Department of Orthopedic Surgery, University of Texas Health Science Center, Houston, TX 77030, USA.
| |
Collapse
|
5
|
Broekhuis D, Boyle R, Karunaratne S, Chua A, Stalley P. Custom designed and 3D-printed titanium pelvic implants for acetabular reconstruction after tumour resection. Hip Int 2023; 33:905-915. [PMID: 36408844 PMCID: PMC10486168 DOI: 10.1177/11207000221135068] [Citation(s) in RCA: 3] [Impact Index Per Article: 3.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 11/07/2021] [Accepted: 07/26/2022] [Indexed: 11/22/2022]
Abstract
BACKGROUND Reconstructive procedure following resection of large pelvic tumours around the hip joint remains a complex challenge. METHODS This study presents a retrospective case series of patients presenting with benign or malignant pelvic tumour for which an internal hemipelvectomy including the hip joint and subsequent reconstruction with a custom designed 3-dimensional printed titanium pelvic implant (3DPPI) has been performed between August 2013 and January 2018. RESULTS 15 consecutive patients with a median age of 33.9 years (IQR 26.4-72.2) and a median BMI of 20.7 kg/m2 (IQR 19.0-33.3) were reviewed after median follow-up of 33.8 months (IQR 24.0-78.1). The majority of patients presented with a malignant tumour as their principal diagnosis (n = 13, 86.7%). The median surgical time was 5.5 hours (IQR 4.5-8.5) and median peri-operative blood loss was 5000 ml (IQR 2000-10000). The median MSTS score at follow-up was 63.3% (IQR 51.7-86.7%). The median NRS in rest was 0.0 (IQR 0.0-5.0), the median NRS during activity was 2.0 (IQR 0.5-7.0) and the median HOOS-PS was 76.6% (IQR 67.9-91.0). 4 patients had implant-specific complications (n = 4, 26.6%); 1 hip dislocation (Henderson type 1a), 3 structural complications (type 3a), 1 deep infection (type 4a) and 1 local tumour recurrence (type 5b). At follow-up, 4 out of 15 implants were classified as a failure, resulting in an implant survival rate of 73.3%. CONCLUSIONS Acceptable peri-operative outcomes, functional results, complication rates and short-term implant survival can be achieved in a cohort of complex patients undergoing 3DPPI reconstruction after hemipelvectomy including the acetabulum.
Collapse
Affiliation(s)
| | - Richard Boyle
- Department of Orthopaedic Surgery, Royal Prince Alfred Hospital, Camperdown, NSW, Australia
| | - Sascha Karunaratne
- Surgical Outcomes Research Centre (SOuRCe), Royal Prince Alfred Hospital, Camperdown, NSW, Australia
| | - Alfred Chua
- Department of Anaesthetics, Royal Prince Alfred Hospital, Camperdown, NSW, Australia
| | - Paul Stalley
- Department of Orthopaedic Surgery, Royal Prince Alfred Hospital, Camperdown, NSW, Australia
| |
Collapse
|
6
|
Li Z, Lu M, Min L, Luo Y, Tu C. Treatment of pelvic giant cell tumor by wide resection with patient-specific bone-cutting guide and reconstruction with 3D-printed personalized implant. J Orthop Surg Res 2023; 18:648. [PMID: 37658436 PMCID: PMC10472683 DOI: 10.1186/s13018-023-04142-4] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 07/03/2023] [Accepted: 08/26/2023] [Indexed: 09/03/2023] Open
Abstract
BACKGROUND This study reports our experience in the treatment of aggressive pelvic GCT through wide resection assisted with patient-specific bone-cutting guides (PSBCGs) and subsequent reconstruction with 3D-printed personalized implants (3DPIs), aiming to present the operative technique of this method and evaluate its clinical efficacy. METHODS We retrospectively analyzed seven patients who underwent wide resection of pelvic GCT followed by reconstruction with 3DPIs from August 2019 to February 2021. There were two males and five females, with a mean age of 43 years. PSBCGs and 3DPIs were prepared using 3D-printing technology. The operational outcomes, local recurrence, radiological results, and any associated complications of this technique were assessed. And the functional outcomes were assessed according to the Musculoskeletal Tumor Society (MSTS) 93 functional score. RESULTS The mean follow-up time was 35.3 months (range 28-45 months). There was no intraoperative complication. Negative surgical margins were achieved in all patients. Postoperative pelvic radiographs showed that 3DPIs matched the shape and size of the bone defect. The anterior-posterior, inlet, and outlet pelvic radiograph demonstrated precise reconstruction consistent with the surgical planning. In addition, tomosynthesis-Shimadzu metal artifact reduction technology (T-SMART) showed good osseointegration at an average of three months after surgery (range 2-4 months). There was no local recurrence or tumor metastasis. The average MSTS score was 24.4 (range 23-27) at the last follow-up. Delayed wound healing was observed in one patient, and the wounds healed after debridement. Prosthesis-related complications were not detected during the follow-up, such as aseptic loosening or structure failure. CONCLUSIONS The treatment of aggressive pelvic GCTs through wide resection assisted with PSBCGs and subsequent reconstruction with 3DPIs is a feasible method, which provides good clinical results and reasonable functional outcomes.
Collapse
Affiliation(s)
- Zhuangzhuang Li
- Department of Orthopedics, Orthopaedic Research Institute, West China Hospital, Sichuan University, No. 37 Guoxue Road, Chengdu, 610041, Sichuan, China
- Model Worker and Craftsman Talent Innovation Workshop of Sichuan Province, West China Hospital, Sichuan University, Chengdu, People's Republic of China
| | - Minxun Lu
- Department of Orthopedics, Orthopaedic Research Institute, West China Hospital, Sichuan University, No. 37 Guoxue Road, Chengdu, 610041, Sichuan, China
- Model Worker and Craftsman Talent Innovation Workshop of Sichuan Province, West China Hospital, Sichuan University, Chengdu, People's Republic of China
| | - Li Min
- Department of Orthopedics, Orthopaedic Research Institute, West China Hospital, Sichuan University, No. 37 Guoxue Road, Chengdu, 610041, Sichuan, China
- Model Worker and Craftsman Talent Innovation Workshop of Sichuan Province, West China Hospital, Sichuan University, Chengdu, People's Republic of China
| | - Yi Luo
- Department of Orthopedics, Orthopaedic Research Institute, West China Hospital, Sichuan University, No. 37 Guoxue Road, Chengdu, 610041, Sichuan, China.
- Model Worker and Craftsman Talent Innovation Workshop of Sichuan Province, West China Hospital, Sichuan University, Chengdu, People's Republic of China.
| | - Chongqi Tu
- Department of Orthopedics, Orthopaedic Research Institute, West China Hospital, Sichuan University, No. 37 Guoxue Road, Chengdu, 610041, Sichuan, China.
- Model Worker and Craftsman Talent Innovation Workshop of Sichuan Province, West China Hospital, Sichuan University, Chengdu, People's Republic of China.
| |
Collapse
|
7
|
Valente G, Benedetti MG, De Paolis M, Donati DM, Taddei F. Differences in hip musculoskeletal loads between limbs during daily activities in patients with 3D-printed hemipelvic reconstructions following tumor surgery. Gait Posture 2023; 102:56-63. [PMID: 36924596 DOI: 10.1016/j.gaitpost.2023.03.005] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 08/05/2022] [Revised: 03/07/2023] [Accepted: 03/09/2023] [Indexed: 03/18/2023]
Abstract
BACKGROUND Anatomical custom-made prostheses, thanks to computer-aided design and 3D-printing technology, help improve osseointegration and reduce mechanical complications in bone reconstructions following bone tumors. A recent quantitative analysis of long-term recovery in patients with 3D-printed reconstructions following pelvic tumor surgery showed asymmetries in ground reaction forces between limbs during different motor activities, while standing very good motor performance and quality of life. RESEARCH QUESTION We analyzed hip contact forces and muscle forces in that cohort of six patients with an innovative custom-made reconstruction of the hemipelvis, and we tested the hypothesis that asymmetries in ground reaction forces would result in more marked differences in musculoskeletal forces. METHODS State-of-the-art musculoskeletal modeling in an optimization-based inverse-dynamics workflow was used to calculate hip contact forces and muscle forces during five motor activities, and the differences between limbs were statistically evaluated across the motor activity cycles and on the force peaks. RESULTS The musculoskeletal loads were found to be not symmetric, as hip loads were generally higher in the contralateral limb. We found significant differences in considerable portions of the motor activities cycles except squat, load symmetry indices indicating a load increase (median up to 25%) on the contralateral limb, especially during stair descent and chair rise/sit, and significantly higher values in the contralateral limb at force peaks. SIGNIFICANCE We confirmed the hypothesis that residual asymmetries found in ground reaction forces were amplified when hip musculoskeletal loads were investigated, reflecting a shift of the loads toward the intact limb. Despite the general trend of higher loads found in the contralateral hip, this cannot be considered a risk of overloading, as both hips supported loads in a physiological range or lower, indicating a likely optimal recovery.
Collapse
Affiliation(s)
- Giordano Valente
- Bioengineering and Computing Laboratory, IRCCS Istituto Ortopedico Rizzoli, Bologna, Italy.
| | - Maria Grazia Benedetti
- Physical Medicine and Rehabilitation Unit, IRCCS Istituto Ortopedico Rizzoli, Bologna, Italy
| | - Massimiliano De Paolis
- Department of Orthopaedics, IRCCS Azienda Ospedaliero-Universitaria di Bologna, Bologna, Italy
| | | | - Fulvia Taddei
- Bioengineering and Computing Laboratory, IRCCS Istituto Ortopedico Rizzoli, Bologna, Italy
| |
Collapse
|
8
|
Palmquist A, Jolic M, Hryha E, Shah FA. Complex geometry and integrated macro-porosity: Clinical applications of electron beam melting to fabricate bespoke bone-anchored implants. Acta Biomater 2023; 156:125-145. [PMID: 35675890 DOI: 10.1016/j.actbio.2022.06.002] [Citation(s) in RCA: 7] [Impact Index Per Article: 7.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 02/15/2022] [Revised: 05/16/2022] [Accepted: 06/01/2022] [Indexed: 01/18/2023]
Abstract
The last decade has witnessed rapid advancements in manufacturing technologies for biomedical implants. Additive manufacturing (or 3D printing) has broken down major barriers in the way of producing complex 3D geometries. Electron beam melting (EBM) is one such 3D printing process applicable to metals and alloys. EBM offers build rates up to two orders of magnitude greater than comparable laser-based technologies and a high vacuum environment to prevent accumulation of trace elements. These features make EBM particularly advantageous for materials susceptible to spontaneous oxidation and nitrogen pick-up when exposed to air (e.g., titanium and titanium-based alloys). For skeletal reconstruction(s), anatomical mimickry and integrated macro-porous architecture to facilitate bone ingrowth are undoubtedly the key features of EBM manufactured implants. Using finite element modelling of physiological loading conditions, the design of a prosthesis may be further personalised. This review looks at the many unique clinical applications of EBM in skeletal repair and the ground-breaking innovations in prosthetic rehabilitation. From a simple acetabular cup to the fifth toe, from the hand-wrist complex to the shoulder, and from vertebral replacement to cranio-maxillofacial reconstruction, EBM has experienced it all. While sternocostal reconstructions might be rare, the repair of long bones using EBM manufactured implants is becoming exceedingly frequent. Despite the various merits, several challenges remain yet untackled. Nevertheless, with the capability to produce osseointegrating implants of any conceivable shape/size, and permissive of bone ingrowth and functional loading, EBM can pave the way for numerous fascinating and novel applications in skeletal repair, regeneration, and rehabilitation. STATEMENT OF SIGNIFICANCE: Electron beam melting (EBM) offers unparalleled possibilities in producing contaminant-free, complex and intricate geometries from alloys of biomedical interest, including Ti6Al4V and CoCr. We review the diverse range of clinical applications of EBM in skeletal repair, both as mass produced off-the-shelf implants and personalised, patient-specific prostheses. From replacing large volumes of disease-affected bone to complex, multi-material reconstructions, almost every part of the human skeleton has been replaced with an EBM manufactured analog to achieve macroscopic anatomical-mimickry. However, various questions regarding long-term performance of patient-specific implants remain unaddressed. Directions for further development include designing personalised implants and prostheses based on simulated loading conditions and accounting for trabecular bone microstructure with respect to physiological factors such as patient's age and disease status.
Collapse
Affiliation(s)
- Anders Palmquist
- Department of Biomaterials, Institute of Clinical Sciences, Sahlgrenska Academy, University of Gothenburg, Gothenburg, Sweden.
| | - Martina Jolic
- Department of Biomaterials, Institute of Clinical Sciences, Sahlgrenska Academy, University of Gothenburg, Gothenburg, Sweden
| | - Eduard Hryha
- Department of Materials and Manufacturing Technologies, Chalmers University of Technology, Gothenburg, Sweden
| | - Furqan A Shah
- Department of Biomaterials, Institute of Clinical Sciences, Sahlgrenska Academy, University of Gothenburg, Gothenburg, Sweden.
| |
Collapse
|
9
|
Zhu Y, Babazadeh-Naseri A, Dunbar NJ, Brake MRW, Zandiyeh P, Li G, Leardini A, Spazzoli B, Fregly BJ. Finite element analysis of screw fixation durability under multiple boundary and loading conditions for a custom pelvic implant. Med Eng Phys 2023; 111:103930. [PMID: 36792235 DOI: 10.1016/j.medengphy.2022.103930] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/09/2022] [Revised: 11/16/2022] [Accepted: 11/21/2022] [Indexed: 11/24/2022]
Abstract
Despite showing promising functional outcomes for pelvic reconstruction after sarcoma resection, custom-made pelvic implants continue to exhibit high complication rates due to fixation failures. Patient-specific finite element models have been utilized by researchers to evaluate implant durability. However, the effect of assumed boundary and loading conditions on failure analysis results of fixation screws remains unknown. In this study, the postoperative stress distributions in the fixation screws of a state-of-the-art custom-made pelvic implant were simulated, and the risk of failure was estimated under various combinations of two bone-implant interaction models (tied vs. frictional contact) and four load cases from level-ground walking and stair activities. The study found that the average weighted peak von Mises stress could increase by 22-fold when the bone-implant interactions were modeled with a frictional contact model instead of a tied model, and the likelihood of fatigue and pullout failure for each screw could change dramatically when different combinations of boundary and loading conditions were used. The inclusion of additional boundary and loading conditions led to a more reliable analysis of fixation durability. These findings demonstrated the importance of simulating multiple boundary conditions and load cases for comprehensive implant design evaluation using finite element analysis.
Collapse
Affiliation(s)
- Yuhui Zhu
- Department of Mechanical Engineering, Rice University, Houston, Texas, USA
| | | | - Nicholas J Dunbar
- Department of Mechanical Engineering, Rice University, Houston, Texas, USA
| | - Matthew R W Brake
- Department of Mechanical Engineering, Rice University, Houston, Texas, USA
| | - Payam Zandiyeh
- Department of Orthopedic Surgery, The University of Texas Health Science Center at Houston, Houston, Texas, USA
| | - Geng Li
- Department of Mechanical Engineering, Rice University, Houston, Texas, USA
| | - Alberto Leardini
- Movement Analysis Laboratory, IRCCS Istituto Ortopedico Rizzoli, Bologna, Italy
| | - Benedetta Spazzoli
- Clinica Ortopedica III, IRCCS Istituto Ortopedico Rizzoli, Bologna, Italy
| | - Benjamin J Fregly
- Department of Mechanical Engineering, Rice University, Houston, Texas, USA.
| |
Collapse
|
10
|
Hsu CL, Yeh TT, Shen PH, Yang JJ, Chu WC, Wu CC. Precise joint preserving surgery by using Three-Dimensional Printing Technology for metastatic periacetabular bone tumor: A technique note and preliminary report. J Formos Med Assoc 2022:S0929-6646(22)00397-7. [DOI: 10.1016/j.jfma.2022.10.013] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/28/2022] [Revised: 09/20/2022] [Accepted: 10/31/2022] [Indexed: 11/13/2022]
|
11
|
Valente G, Benedetti MG, Paolis MD, Sambri A, Frisoni T, Leardini A, Donati DM, Taddei F. Long-term functional recovery in patients with custom-made 3D-printed anatomical pelvic prostheses following bone tumor excision. Gait Posture 2022; 97:73-79. [PMID: 35914386 DOI: 10.1016/j.gaitpost.2022.07.248] [Citation(s) in RCA: 2] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 01/18/2022] [Revised: 07/19/2022] [Accepted: 07/21/2022] [Indexed: 02/02/2023]
Abstract
BACKGROUND Anatomical custom-made prostheses make it possible to reconstruct complicated bone defects following excision of bone tumors, thanks to 3D-printed technology. To date, clinical measures have been used to report clinical-functional outcome and provide evidence for the effectiveness of this new surgical approach. However, there are no studies that quantified the achievable recovery during common activities by using instrumental clinical-functional evaluation in these patients. RESEARCH QUESTION What is the motor performance, functional outcome and quality of life in patients with custom-made 3D-printed pelvic prostheses following bone tumor? METHODS To analyze motor performance, six patients performed motion analysis during five motor activities at follow-up of 32 ± 18 months. Joint angles, ground reaction forces and joint moments of the operated and contralateral limbs were compared. On-off activity of lower-limb muscles were calculated from electromyography and compared to a healthy matched population. To analyze functional outcome and quality of life, differences in measured hip abductor strength between limbs were evaluated, as well as clinical-functional scores (Harris Hip Score, Barthel Index, Musculoskeletal Tumor Society score), and quality of life (SF-36 health survey). RESULTS We found only slight differences in joint kinematics when comparing operated and contralateral limb. The activity of gluteal muscles was normal, while hamstrings showed out-of-phase activities. Ground reaction forces and hip moments showed asymmetries between limbs, particularly in more demanding motor activities. We found a mean difference in hip abductor strength of 48 ± 82 N between limbs, good clinical-functional scores, and quality of life scores within normative. SIGNIFICANCE Our study showed optimal long-term results in functional recovery, mainly achieved through recovery of the gluteal function, although minor impairments were found, which may be considered for future improvement of this innovative surgery. The effect of a more loaded contralateral limb on internal loads and long-term performance of the implant remains unknown and deserves further investigation.
Collapse
Affiliation(s)
- Giordano Valente
- Bioengineering and Computing Laboratory, IRCCS Istituto Ortopedico Rizzoli, Bologna, Italy.
| | - Maria Grazia Benedetti
- Physical Medicine and Rehabilitation Unit, IRCCS Istituto Ortopedico Rizzoli, Bologna, Italy.
| | - Massimiliano De Paolis
- Department of Orthopaedics, IRCCS Azienda Ospedaliero-Universitaria di Bologna, Bologna, Italy.
| | - Andrea Sambri
- Department of Orthopaedics, IRCCS Azienda Ospedaliero-Universitaria di Bologna, Bologna, Italy.
| | - Tommaso Frisoni
- Orthopaedic Oncology, IRCCS Istituto Ortopedico Rizzoli, Bologna, Italy.
| | - Alberto Leardini
- Movement Analysis Laboratory, IRCCS Istituto Ortopedico Rizzoli, Bologna, Italy.
| | | | - Fulvia Taddei
- Bioengineering and Computing Laboratory, IRCCS Istituto Ortopedico Rizzoli, Bologna, Italy.
| |
Collapse
|
12
|
牛 晓, 金 韬, 徐 海. [Application of three-dimensional printing technology in treatment of limb bone tumors]. ZHONGGUO XIU FU CHONG JIAN WAI KE ZA ZHI = ZHONGGUO XIUFU CHONGJIAN WAIKE ZAZHI = CHINESE JOURNAL OF REPARATIVE AND RECONSTRUCTIVE SURGERY 2022; 36:790-795. [PMID: 35848172 PMCID: PMC9288913 DOI: 10.7507/1002-1892.202203006] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Subscribe] [Scholar Register] [Received: 03/02/2022] [Revised: 05/13/2022] [Accepted: 05/16/2022] [Indexed: 01/24/2023]
Abstract
With the developing of three-dimensional (3D) printing technology, it is widely used in the treatment of bone tumors in the clinical orthopedics. Because of the great individual differences in the location of bone tumor, resection and reconstruction are difficult. Based on 3D printing technology, the 3D models can be prepared to show the anatomical part of the disease, so that the surgeons can create a patient-specific operational plans based on better understand the local conditions. At the same time, preoperative simulation can also be carried out for complex operations and patient-specific prostheses can be further designed and prepared according to the location and size of tumor, which may have more advantages in adaptability. In this paper, the domestic and international research progress of 3D printing technology in the treatment of limb bone tumors in recent years were reviewed and summarized.
Collapse
Affiliation(s)
- 晓辉 牛
- 北京积水潭医院骨肿瘤科(北京 102208)Department of Orthopaedic Oncology Surgery, Beijing Jishuitan Hospital, Beijing, 102208, P. R. China
| | - 韬 金
- 北京积水潭医院骨肿瘤科(北京 102208)Department of Orthopaedic Oncology Surgery, Beijing Jishuitan Hospital, Beijing, 102208, P. R. China
| | - 海荣 徐
- 北京积水潭医院骨肿瘤科(北京 102208)Department of Orthopaedic Oncology Surgery, Beijing Jishuitan Hospital, Beijing, 102208, P. R. China
| |
Collapse
|
13
|
郭 卫. [Pelvic limb-salvage surgery for malignant tumors: 30 years of progress in China]. ZHONGGUO XIU FU CHONG JIAN WAI KE ZA ZHI = ZHONGGUO XIUFU CHONGJIAN WAIKE ZAZHI = CHINESE JOURNAL OF REPARATIVE AND RECONSTRUCTIVE SURGERY 2022; 36:781-789. [PMID: 35848171 PMCID: PMC9288902 DOI: 10.7507/1002-1892.202112059] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Subscribe] [Scholar Register] [Received: 12/16/2021] [Revised: 04/25/2022] [Indexed: 01/24/2023]
Abstract
This article reviews the development and progress in the field of limb salvage treatment, surgical techniques, and function reconstruction of pelvic malignant tumors in China in the past 30 years. Based on the surgical classification of pelvic tumor resection in different parts, the development of surgical techniques and bone defect repair and reconstruction methods were described in detail. In recent years, in view of the worldwide problem of biological reconstruction after pelvic tumor resection, Chinese researchers have systematically proposed the repair and reconstruction methods and prosthesis design for bone defects after resection of different parts for the first time in the world. In addition, a systematic surgical classification (Beijing classification) was first proposed for the difficult situation of pelvic tumors involving the sacrum, as well as the corresponding surgical plan and repair and reconstruction methods. Through unremitting efforts, the limb salvage rate of pelvic malignant tumors in China has reached more than 80%, which has preserved limbs and restored walking function for the majority of patients, greatly reduced surgical complications, and achieved internationally remarkable results.
Collapse
Affiliation(s)
- 卫 郭
- 北京大学人民医院骨肿瘤科(北京 100044)Department of Orthopaedic Oncology, Peking University, People’s Hospital, Beijing, 100044, P. R. China
- 北京大学人民医院肉瘤及罕见肿瘤诊疗中心(北京 100044)Sarcoma and Rare Tumor Center, Peking University, People’s Hospital, Beijing, 100044, P. R. China
| |
Collapse
|
14
|
Xu S, Guo Z, Shen Q, Peng Y, Li J, Li S, He P, Jiang Z, Que Y, Cao K, Hu B, Hu Y. Reconstruction of Tumor-Induced Pelvic Defects With Customized, Three-Dimensional Printed Prostheses. Front Oncol 2022; 12:935059. [PMID: 35847863 PMCID: PMC9282862 DOI: 10.3389/fonc.2022.935059] [Citation(s) in RCA: 7] [Impact Index Per Article: 3.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/03/2022] [Accepted: 06/02/2022] [Indexed: 11/17/2022] Open
Abstract
Background Reconstruction of pelvis girdle stability after tumor-induced hemipelvectomy remains challenging. We surgically treated 13 patients with custom-made, three-dimensional printed hemipelvic prostheses. We aim to identify the preliminary outcomes for patients who have been managed with more mixed regions of prosthetic pelvic reconstruction and the feasibility of two reconstructive systems. Methods Seven male patients and 6 female patients treated at our center between January 2019 and May 2021 were included. There were 11 primary sarcomas and 2 solitary bone metastases. After en bloc tumor resection, two types of personalized, three-dimensional printed prostheses were fixed to restore the stability and rebuild the load transfer. The position of the reconstructed hemipelvis was evaluated on an anteroposterior plain radiograph. The complications and outcomes were traced. One amputation specimen was discovered through histological analysis of the porous structure. Results The operative duration was 467 ± 144 min, and the blood loss was 3,119 ± 662 ml. During a follow-up of 22.4 ± 8.5 months, two patients had delayed wound healing and one had a second-stage flap transfer. One patient with osteosarcoma died of pulmonary metastasis 27 months after surgery. Two patients with marginal resection suffered from local recurrence and had extra surgeries. One patient had traumatic hip dislocation 2 months after surgery and manipulative reduction was performed. The acetabular inclination of the affected side was 42.2 ± 4.3°, compared with 42.1 ± 3.9° on the contralateral side. The horizontal distance between the center of the femoral head and the middle vertical line was 10.4 ± 0.6 cm, while the reconstructed side was 9.8 ± 0.8 cm. No significant difference in acetabular position after surgery was found (p > 0.05). The amputation specimen harvested from one patient with local recurrence demonstrated bone and soft tissue ingrowth within the three-dimensional printed trabecular structure. Walking ability was preserved in all patients who are still alive and no prosthesis-related complications occurred. The MSTS score was 22.0 ± 3.7. Conclusions Both types of custom-made, three-dimensional printed prostheses manifested excellent precision, mechanical stability, and promising functional rehabilitation. The porous structure exhibited favorable histocompatibility to facilitate the ingrowth of bone and soft tissue.
Collapse
|
15
|
Clinical Outcome and Fracture Risk Prediction of Benign Bone Tumors on the Acetabular Dome: 7-Year Clinical Experience and a Finite Element Analysis. EVIDENCE-BASED COMPLEMENTARY AND ALTERNATIVE MEDICINE 2022; 2022:5150474. [PMID: 35321500 PMCID: PMC8938047 DOI: 10.1155/2022/5150474] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 11/02/2021] [Revised: 01/05/2022] [Accepted: 02/17/2022] [Indexed: 02/05/2023]
Abstract
The treatment of benign pelvic lesions and tumors is still a challenge in clinical orthopedics. The surgical procedure was complicated and the postoperative complication was hard to avoid usually. The purpose of this study is to analyze the clinical outcome and predict the fracture risk of benign bone tumors on acetabular dome by finite element analysis. In our research, clinical data of 25 patients were collected from January 2010 to January 2017, including basic information of patients, reconstruction methods, complications, and postoperative MSTS function scores. Finite element analysis (FEA) was used to predict the fracture risk when a benign tumor involved an acetabular dome. 25 patients were followed up for 37.5 ± 5.6 (ranging from 24 to 78) months. Intraoperative bleeding was 100–3000 ml (mean 858.3 ml). The postoperative MSTS93 score was 19.61 ± 7.32 before operation and 26.28 ± 15.59 at the last follow-up. The results of finite element analysis suggest that there was a high risk for pathological fracture in the following: both columns were damaged by tumors; the anterior column and 50% of the posterior column were affected. Other cases were in the low fracture risk group. Based on this study, we believe that, according to the risk assessment results of tumor cavity fracture suggested by the FEA results, combined with the nature of tumor, it may become a useful tool which is a great significance to guide the operation plan, select the operation time, and guide the postoperative functional exercise.
Collapse
|
16
|
Döring K, Staats K, Puchner S, Windhager R. Patient-Specific Implants for Pelvic Tumor Resections. J Pers Med 2021; 11:jpm11080683. [PMID: 34442327 PMCID: PMC8399992 DOI: 10.3390/jpm11080683] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/29/2021] [Revised: 07/16/2021] [Accepted: 07/19/2021] [Indexed: 12/15/2022] Open
Abstract
Introduction Limb salvage surgery for periacetabular malignancies is technically demanding and associated with a considerable likelihood of postoperative complications and surgical revision. Reconstruction using custom-made implants represents the treatment of choice. This study was conducted to analyze treatment outcomes of custom-made implants in a single orthopaedic tumor center. Patients and Methods Twenty patients with a histologically verified periacetabular malignancy and a median follow up time of 5 (1-17) years were included. Results The median number of revision surgeries per patient was 1.5 (0-7). Complications were dislocations in 3 patients, aseptic loosening in 4 patients, deep infections in 9 patients, thromboembolic events in 5 patients and sciatic nerve lesions in 4 patients. Overall survival was 77% after one year, 69% after two years and 46% after five years. Median Harris Hip Score was 81 (37-92) points at last follow up. Conclusion Although internal hemipelvectomy and reconstruction using custom-made implants is linked with a high risk of postoperative complications, good functional outcomes can be regularly achieved. This information may help treating surgeons to find adequate indications, as eligible patients need to be critically selected and integrated into the decision-making process.
Collapse
|
17
|
Pelvic Chondrosarcoma Treated by En Bloc Resection with Patient-Specific Osteotomy Guides and Reimplantation of the Extracorporeally Irradiated Bone as an Osseocartilaginous Structural Orthotopic Autograft: A Report of Two Cases with Description of the Surgical Technique. Case Rep Orthop 2021; 2021:5512143. [PMID: 33868736 PMCID: PMC8035037 DOI: 10.1155/2021/5512143] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 01/28/2021] [Revised: 03/21/2021] [Accepted: 03/27/2021] [Indexed: 11/18/2022] Open
Abstract
Primary tumors of the pelvis are considered difficult to treat due to the complex anatomy and the proximity of important neurovascular structures. The surgical armamentarium for the treatment of these tumors has evolved with the help of cutting-edge technology from debilitating hemipelvectomies to solutions such as precise resections guided by patient-specific instruments or computer navigation and reconstruction by modular prostheses, 3D-printed custom-made implants, or orthotopic autograft reimplantation after extracorporeal irradiation. Different combinations of these techniques have been described in the literature with various rates of success. We present two cases of pelvic chondrosarcomas successfully treated by a combination of periacetabular resection with patient-specific osteotomy guides and orthotopic reimplantation of the extracorporeally irradiated autograft resulting in retention of the native hip.
Collapse
|
18
|
Park JW, Kang HG, Kim JH, Kim HS. The application of 3D-printing technology in pelvic bone tumor surgery. J Orthop Sci 2021; 26:276-283. [PMID: 32247647 DOI: 10.1016/j.jos.2020.03.004] [Citation(s) in RCA: 22] [Impact Index Per Article: 7.3] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 12/23/2019] [Revised: 02/22/2020] [Accepted: 03/03/2020] [Indexed: 12/15/2022]
Abstract
BACKGROUND Three-dimensional (3D)-printing technology provides an advanced approach to pelvic bone tumor resection and reconstruction. However, only a few cases of pelvic bone tumor surgery using 3D-printing have been reported due to limited time since the introduction of the new implant. This study introduces pelvic bone tumor surgeries using 3D-printed bone-cutting guides and implants. METHODS This single-center retrospective review included 12 patients who underwent malignant pelvic bone tumor surgeries using a 3D-printed bone-cutting guide and/or implant. Clinical information was collected regarding patient demographics, tumor characteristics, pathologic diagnosis, surgery details, and functional recovery. RESULTS Type I internal hemipelvectomy was performed using 3D-printed bone-cutting guides for 4 patients that underwent cavitary bone tumor resection of the ilium. For 3 of these 4 patients, cavitary bone defects were filled with structural allobone graft precisely trimmed by the 3D-printed allograft-shaping guide (n = 1) and 3D-printed mesh-style titanium spacer (n = 2). For type II and III areas, one and two patients, respectively, underwent 3D-printing-assisted surgery. Five patients underwent type I, II, and III pelvic resection using 3D-printed cutting guides and reconstruction with 3D-printed implants. In all patients, independent gait was recovered except for a patient who underwent hindquarter amputation 4 months postoperatively because of local recurrence. CONCLUSIONS This study provides preliminary, short-term data on the efficacy and safety of pelvic bone tumor surgery using 3D-printing.
Collapse
Affiliation(s)
- Jong Woong Park
- Orthopaedic Oncology Clinic, National Cancer Center, 323 Ilsan-ro, Ilsandong-gu, Goyang-si Gyeonggi-do, 10408, South Korea; Division of Convergence Technology, National Cancer Center, 323 Ilsan-ro, Ilsandong-gu, Goyang-si Gyeonggi-do, 10408, South Korea
| | - Hyun Guy Kang
- Orthopaedic Oncology Clinic, National Cancer Center, 323 Ilsan-ro, Ilsandong-gu, Goyang-si Gyeonggi-do, 10408, South Korea; Division of Convergence Technology, National Cancer Center, 323 Ilsan-ro, Ilsandong-gu, Goyang-si Gyeonggi-do, 10408, South Korea.
| | - June Hyuk Kim
- Orthopaedic Oncology Clinic, National Cancer Center, 323 Ilsan-ro, Ilsandong-gu, Goyang-si Gyeonggi-do, 10408, South Korea
| | - Han-Soo Kim
- Department of Orthopaedic Surgery, Seoul National University Hospital, 101 Daehak-ro Jongno-gu, Seoul 03080, South Korea
| |
Collapse
|
19
|
Techniques and outcomes of hip abductor reconstruction following tumor resection in adults. Orthop Traumatol Surg Res 2021; 107:102765. [PMID: 33321236 DOI: 10.1016/j.otsr.2020.102765] [Citation(s) in RCA: 3] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 12/03/2019] [Accepted: 05/25/2020] [Indexed: 02/03/2023]
Abstract
The function of the abductor mechanism (AM) of the hip can be disturbed, or even compromised, following tumor resection in the hip area. The consequences are instability (limping, dislocation), pain and altered walking ability. Several reconstruction techniques can be used for the same AM sacrifice. After defining the AM, this lecture will discuss the best technique for a given type of bone and muscle resection. These reconstruction techniques depend on exactly where the AM was sacrificed. For zone 1 resections of the ilium and/or iliac gluteal insertions, reconstruction is often optional. When muscle from the AM is resected, especially when the gluteal tendon is detached from its trochanteric insertion, isolated reconstruction can be done or reconstruction in combination with a tendon allograft or an allograft and/or tendon transfer from the surrounding area. This sacrifice, whether followed by reconstruction or not, in most cases leads to a good functional outcome, except when a complete musculotendinous unit or the superior gluteal nerve is sacrificed. Isolated resection of the greater trochanter is rare; however, this completely disrupts the continuity of the AM and justifies reconstruction, often using a bone-tendon allograft. Proximal femur resection is the most common scenario. The extent of the trochanteric resection and the gluteal tendon attachments drives the type of prosthesis used. The two most used techniques consist in an allograft sleeve over a long cemented femoral stem (allograft prosthesis composite - APC) or a modular proximal femoral endoprosthesis (megaprosthesis) with a specific AM fixation system (small plate or wire cerclage, resorbable or metal wire, synthetic reattachment tube). These two techniques yield nearly identical long-term functional outcomes with complications specific to each: osteolysis and fracture for APC, failure of tendon reattachment for megaprosthesis. Beyond these technical considerations, one must consider the poor availability of massive bone allografts. This is a highly relevant issue in France, and partially explains the shift to reconstruction with a megaprosthesis. Lastly, we will look at the different clinical and diagnostic tests used to evaluate the function of the AM in an oncology context and the outcomes of the various types of reconstruction.
Collapse
|
20
|
Reconstruction of Bony Defects after Tumor Resection with 3D-Printed Anatomically Conforming Pelvic Prostheses through a Novel Treatment Strategy. BIOMED RESEARCH INTERNATIONAL 2020; 2020:8513070. [PMID: 33335928 PMCID: PMC7723494 DOI: 10.1155/2020/8513070] [Citation(s) in RCA: 17] [Impact Index Per Article: 4.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 08/05/2020] [Revised: 10/09/2020] [Accepted: 11/11/2020] [Indexed: 01/07/2023]
Abstract
There has been an increasing interest and enormous applications in three-dimensional (3D) printing technology and its prosthesis, driving many orthopaedic surgeons to solve the difficult problem of bony defects and explore new ways in surgery approach. However, the most urgent problem is without an effective prosthesis and standard treatment strategy. In order to resolve these problems, this study was performed to explore the use of a 3D-printed anatomically conforming pelvic prosthesis for bony defect reconstruction following tumor resection and to describe a detailed treatment flowchart and the selection of a surgical approach. Six patients aged 48-69 years who had undergone pelvic tumor resection underwent reconstruction using 3D-printed anatomically conforming pelvic prostheses according to individualized bony defects between March 2016 and June 2018. According to the Enneking and Dunham classification, two patients with region I+II tumor involvement underwent reconstruction using the pubic tubercle-anterior superior iliac spine approach and the lateral auxiliary approach and one patient with region II+III and three patients with region I+II+III tumor involvement underwent reconstruction using the pubic tubercle-posterior superior iliac spine approach. The diagnoses were chondrosarcoma and massive osteolysis. After a mean follow-up duration of 30.33 ± 9.89 months (range, 18-42), all patients were alive, without evidence of local recurrence or distant metastases. The average blood loss and blood transfusion volumes during surgery were 2500.00 ± 1461.51 ml (range, 1200-5000) and 2220.00 ± 1277.62 ml (range, 800-4080), respectively. During follow-up, the mean visual analogue scale (VAS) score decreased, and the mean Harris hip score increased. There were no signs of hip dislocation, prosthetic loosening, delayed wound healing, or periprosthetic infection. This preliminary study suggests the clinical effectiveness of 3D-printed anatomically conforming pelvic prostheses to reconstruct bony defects and provide anatomical support for pelvic organs. A new surgical approach that can be used to expose and facilitate the installation of 3D-printed prostheses and a new treatment strategy are presented. Further studies with a longer follow-up duration and larger sample size are needed to confirm these encouraging results.
Collapse
|
21
|
Milovanovic JR, Stojkovic MS, Husain KN, Korunovic ND, Arandjelovic J. Holistic Approach in Designing the Personalized Bone Scaffold: The Case of Reconstruction of Large Missing Piece of Mandible Caused by Congenital Anatomic Anomaly. JOURNAL OF HEALTHCARE ENGINEERING 2020; 2020:6689961. [PMID: 33299535 PMCID: PMC7704195 DOI: 10.1155/2020/6689961] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 10/22/2020] [Revised: 11/09/2020] [Accepted: 11/16/2020] [Indexed: 12/03/2022]
Abstract
The paper reports on the importance of applying the holistic approach in designing a personalized bone scaffold, but also all other kinds of personalized implants. In addition, the paper attempts to point out the important aspects of the design of a PBS against which the quality of a realistic and applicable design solution should be assessed. The holistic approach refers to the adaptation of design features of a bone scaffold to the multilateral specifics related to the particular patient, its surgical case, and curing treatment. To ensure a successful application, five aspects of personalized bone scaffold design should be considered while it is being adapted: anatomical congruency, mechanical conformity, biochemical compatibility and biodegradability, manufacturability, and implantability. To demonstrate the importance of applying a holistic approach in designing a personalized bone scaffold, the paper shows a case where a patient-specific scaffold aimed at the reconstruction of a large missing piece of mandible was designed. The research resulted in a series of recommendations regarding the methods of bone geometry reconstruction and scaffold design. The paper sheds new light on the desired mechanical properties of a personalized bone scaffold while also recommending possible design parameters for optimizing the construction according to these properties. Finally, it recommends a possible procedure of integral production of personalized bone scaffold and bone graft. The presented so-called holistic approach announces a new systematic process of designing a personalized bone scaffold, which, although requiring a comprehensive consideration of complex requirements, is inevitable to make the designed solution applicable.
Collapse
Affiliation(s)
- Jelena R. Milovanovic
- Department of Production Information Technologies, University of Nis, Faculty of Mechanical Engineering, 18000 Nis, Serbia
| | - Milos S. Stojkovic
- Department of Production Information Technologies, University of Nis, Faculty of Mechanical Engineering, 18000 Nis, Serbia
| | - Karim N. Husain
- University of Al-Qadisiyah, Faculty of Mechanical Engineering, 58001 Al Diwaniyah, Iraq
| | - Nikola D. Korunovic
- Department of Production Information Technologies, University of Nis, Faculty of Mechanical Engineering, 18000 Nis, Serbia
| | - Jovan Arandjelovic
- Department of Production Information Technologies, University of Nis, Faculty of Mechanical Engineering, 18000 Nis, Serbia
| |
Collapse
|