Finite element analysis of two cephalomedullary nails in treatment of elderly reverse obliquity intertrochanteric fractures: zimmer natural nail and proximal femoral nail antirotation-ΙΙ

Finite element analysis of proximal femur bionic nail for treating intertrochanteric fractures in osteoporotic bone

This study compared the biomechanical characteristics of proximal femur bionic nail (PFBN) and proximal femoral nail antirotation (PFNA) in treating osteoporotic femoral intertrochanteric fractures using finite element analysis. Under similar bone density, the PFBN outperforms the PFNA in maximum femoral displacement, internal fixation displacement, stress distribution in the femoral head and internal fixation components, and femoral neck varus angle. As the bone density decreases, the PFBN's biomechanical advantages over PFNA become more pronounced. This finding suggests that the PFBN is superior for treating osteoporotic intertrochanteric femoral fractures.

Biomechanical comparison of an intramedullary nail combined with a reconstruction plate combination versus a single intramedullary nail in unstable intertrochanteric fractures with lateral femoral wall fracture: A finite element analysis

This study aimed to compare the biomechanical performance of an intramedullary nail combined with a reconstruction plate and a single intramedullary nail in the treatment of unstable intertrochanteric femoral fractures with a fracture of the lateral femoral wall (LFW). A three-dimensional finite element (FE) femur model was established from computed tomography images of a healthy male volunteer. A major reverse obliquity fracture line, associated with a lesser trochanteric fragment defect and a free bone fragment of the LFW, was developed to create an AO/OTA type 31-A3.3 unstable intertrochanteric fracture mode. Two fixation styles were simulated: a long InterTAN nail (ITN) with or without a reconstruction plate (RP). A vertical load of 2100 N was applied to the femoral head to simulate normal walking. The construct stiffness, von Mises stress, and model displacement were assessed. The ITN with RP fixation (ITN/RP) provided higher axial stiffness (804 N/mm) than the ITN construct (621 N/mm). The construct stiffness of ITN/RP fixation was 29% higher than that of ITN fixation. The peak von Mises stress of the implants in the ITN/RP and ITN models was 994.46 MPa and 1235.24 MPa, respectively. The peak stress of the implants in the ITN/RP model decreased by 24% compared to that of the ITN model. The peak von Mises stress of the femur in the ITN/RP model was 269.06 MPa, which was lower than that of the ITN model (331.37 MPa). The peak stress of the femur in the ITN/RP model was 23% lower than that of the ITN model. The maximum displacements of the ITN/RP and ITN models were 12.12 mm and 13.53 mm, respectively. The maximum displacement of the ITN/RP model decreased by 12% compared with that of the ITN model. The study suggested that an additional plate fixation could increase the construct stiffness, reduce the stresses in the implant and femur, and decrease displacement after intramedullary nailing. Therefore, the intramedullary nail and reconstruction plate combination may provide biomechanical advantages over the single intramedullary nail in unstable intertrochanteric fractures with a fractured LFW.

Biomechanical performance of short and long cephalomedullary nail constructs for stabilizing different levels of subtrochanteric fracture

INTRODUCTION

The aim of this study was to assess biomechanical performance of short and long Cephalomedullary nail constructs consisting of different number of distal screw for stabilizing different levels of subtrochanteric fracture.

MATERIALS AND METHODS

The femur obtained from computed tomography scanner was used to create a transverse fracture at 15 mm (level A), 35 mm (level B), and 55 mm (level C) below the lesser trochanter. Short and long Cephalomedullary nails were virtually inserted to the fractured femur. Four-node tetrahedral element was used to build up finite element (FE) models for biomechanical analysis. The analysis focused on post-operative stage of partial weight-bearing.

RESULTS

Stress on the implant localized at the surface between lag screw/nail and distal screw/nail. Short Cephalomedullary nail exhibited higher stress than long Cephalomedullary nail. The stress in short Cephalomedullary nail could be reduced by using two distal screws fixation and the fracture at level A produced less stress than that of level B and C. Either short or long nail with two distal screws is sufficient to withstand the stress magnitude produced from the physiologic load. When single dynamic distal screw was used, stress on implant, elastic strain at fracture gap, and bone stress reached the high values. Elastic strain of the fracture gap at level C were less than that of level A and B, but no statistically significant difference. There was no proximal cancellous bone damage observed from the FE analysis.

CONCLUSIONS

Long Cephalomedullary nail with at least two distal locking screws remains a proper implant for subtrochanteric fracture fixation in overall locations. However, short Cephalomedullary nail with two distal screws may be a candidate for a high subtrochanteric fracture. Single dynamic screw insertion is strongly not recommended with either short or long nail regarding implant failure.

Biomechanical analysis of the treatment of intertrochanteric hip fracture with different lengths of dynamic hip screw side plates

BACKGROUND

Dynamic hip screw (DHS) is a common implant used to treat stable-type intertrochanteric hip fractures. There are many factors that can affect the success rate of the surgery, including the length of side plates. It is therefore important to investigate the biomechanical effect of different DHS side plates on bones.

OBJECTIVE

In order to reduce the likelihood of an implant failure, the aim of this study was to use finite element analysis (FEA) to investigate and understand the effect of side plates with different lengths in DHS.

METHODS

In this FEA study, a 3D model with cortical bone, cancellous bone, side plate, lag screw, and cortical screws to simulate the implantation of DHS with different lengths of side plate (2-hole, 4-hole, and 6-hole) for intertrochanteric hip fractures was constructed. The loading condition was used to simulate the force (400 N) on the femoral head and the stress distribution on the lag screw, side plate, cortical screws, and femur was measured.

RESULTS

The highest stress points occured around the region of contact between the screw and the cortical bones. The stress on the femur at the most distal cortical screw was the greatest. The shorter the length of the side plate, the greater the stress on the cortical screws, resulting in an increased stress on the femur surrounding the cortical screws.

CONCLUSIONS

The use of DHS with 2-hole side plate may increase the risk of side plate pull-out. The results of this study provide a biomechanical analysis for selection of DHS implant lengths that can be useful for orthopaedic surgeons.