Management of instability after primary total knee arthroplasty: an evidence-based review

Impact of Joint Laxity on 2-Year KOOS Outcomes of Posterior Stabilized Total Knee Arthroplasty

The objective of this study was to determine relationships between intraoperative posterior cruciate ligament (PCL) sacrificing posterior stabilized (PS) total knee arthroplasty (TKA) laxity measurements throughout flexion and patient outcomes at 2 years post-TKA and to define clinically relevant laxity thresholds to optimize patient outcomes.In a single-surgeon study, PCL sacrificing TKA using a robotics-assisted platform with a digital joint tensioning device was performed in 115 knees in 115 patients. Final intraoperative joint laxity was recorded, and 2-year Knee Injury and Osteoarthritis Outcome Scores (KOOSs) were obtained. A Simulated Annealing optimization algorithm was used to identify medial and lateral laxity windows which maximized the 2-year KOOS pain score. Wilcoxon nonparametric tests were used to compare outcomes between groups.Significant associations were found between intraoperative joint laxity and 2-year KOOS pain outcomes throughout flexion. Clinically relevant laxity windows were defined medially and laterally in mid-flexion and flexion for improved outcomes, whereas only a lateral laxity window could be defined in extension. When all laxity windows were satisfied, a 14.5-KOOS point improvement was found (97.2 vs. 77.8, p = 0.0060) compared to knees which did not satisfy any window. Improvements in Activities of Daily Living (Δ8.8, p = 0.0143), Sports (Δ22.5, p = 0.0108), and Quality of Life (Δ18.7, p = 0.0011) KOOS subscores were also found in knees which satisfied all windows versus 0-1 window.Intraoperative joint laxity is associated with postoperative outcomes in a PS knee design, wherein patients balanced within identified laxity targets reported improved outcomes over those that did not. Clinically significant thresholds were defined and were predominately found in mid-flexion and flexion for medial and lateral laxity. When target windows were combined further improved outcomes were identified.

Revisiting the universal femoral component: Midterm outcomes of a modern design

Introduction

Approximately 10 years ago a total knee arthroplasty system with a modern universal femoral component was introduced. It includes a symmetrical femoral and tibial component. The purpose of this study was to evaluate the 6-year clinical outcomes of this implant from a single surgeon.

Materials and methods

A retrospective chart review was performed on all patients who received a TJO Klassic® Knee from January 2014 to January 2015 (Total Joint Orthopedics Inc., Salt Lake City, Utah). In total there were 131 patients (149 knees) who underwent total knee arthroplasty with this system. A retrospective chart review was performed including demographics, preoperative and postoperative clinical assessments including Knee Society score (KSS), range of motion, and radiographic assessment.

Results

There were 60 males (45.8 %) and 71 females (54.2 %) with 149 knees available for review. Mean age at time of surgery was 67.4 years (45-91) and BMI was 32.6 kg/m2 (16.6-54.6). The patella was left unresurfaced in 37 knees (24.8 %), KSS scores including the clinical and functional components all improved significantly (p < 0.001). ROM improved significantly (p < 0.001). 9 knees underwent reoperation within 6 years of their index operation: 2 quadriceps tendon repairs, 3 polyethylene exchanges for laxity, 2 two-stage revisions for infection, 1 revision for aseptic loosening of the femur, and 1 for post-traumatic patella fracture.

Conclusion

6-year outcomes of a modern universal femoral design demonstrate excellent clinical results and survivorship equal to modern asymmetrical femur designs. There were no known instances of patellar maltracking.

Early monitoring of inlay wear after total knee arthroplasty on plain radiographs using model-based wear measurement

Wear of the ultra-high molecular-weight polyethylene (UHMWPE) component in total knee arthroplasty contributes to implant failure. It is often detected late, when patients experience pain or instability. Early monitoring could enable timely intervention, preventing implant failure and joint degeneration. This study investigates the accuracy and precision (repeatability) of model-based wear measurement (MBWM), a novel technique that can estimate inlay thickness and wear radiographically. Six inlays were milled from non-crosslinked UHMWPE and imaged via X-ray in anteroposterior view at flexion angles 0°, 30°, and 60° on a phantom knee model. MBWM measurements were compared with reference values from a coordinate measurement machine. Three inlays were subjected to accelerated wear generation and similarly evaluated. MBWM estimated inlay thickness with medial and lateral accuracies of 0.13 ± 0.09 and 0.14 ± 0.09 mm, respectively, and linear wear with an accuracy of 0.07 ± 0.06 mm. Thickness measurements revealed significant lateral differences at 0° and 30° (0.22 ± 0.08 mm vs. 0.06 ± 0.06 mm, respectively; t-test, p = 0.0002). Precision was high, with average medial and lateral differences of - 0.01 ± 0.04 mm between double experiments. MBWM using plain radiographs presents a practical and promising approach for the clinical detection of implant wear.

Metaphyseal trauma of the lower extremities in major orthopedic surgery as an independent risk factor for deep vein thrombosis

PURPOSE

Major orthopedic surgeries of the lower extremities, which heavily injure the metaphyseal region, are strongly associated with the risk of developing deep vein thrombosis (DVT). This study aims to investigate the role of metaphyseal trauma as an independent risk factor for DVT.

METHODS

Patients undergoing major orthopedic surgery of the hip and knee had their existing DVT risk factors recorded. Metaphyseal trauma was defined by the extent of bone injury during these surgeries. The samples were categorized into three surgery groups: total arthroplasty group (TA), hemiarthroplasty group (HA), and the open reduction internal fixation group (ORIF). Logistic regression test between significant existing risk factors and surgery groups determines the independent association between risk factors and DVT.

RESULT

The study found a 24.8% incidence of asymptomatic DVT in patients undergoing major orthopedic surgeries, with the highest prevalence (37.2%) in TA, which had the largest extent of metaphyseal trauma and the least existing DVT risk factors. TA showed 6.2 OR and 95% CI (p = 0.036) compared to the other existing risk factor in relation to DVT incidence.

CONCLUSION

Metaphyseal bone trauma in the hip and knee major orthopedic surgery is an independent risk factor for deep vein thrombosis.

Effect of Surgeon Volume on Mechanical Complications after Resection Arthroplasty with Articulating Spacer

Two-stage revision with an antibiotic-loaded cement articulating spacer is a standard treatment for chronic prosthetic knee infection (PKI); however, mechanical complications can occur during the spacer period. There is limited evidence on the association between surgeon volume and mechanical complications after resection arthroplasty (RA) using an articulating spacer. This study aimed to compare the rates of mechanical complications and reoperation after RA with articulating spacers by surgeons with high volumes (HV) and low volumes (LV) of RA performed and analyzed the risk factors for mechanical failure. The retrospective study investigated 203 patients treated with PKIs who underwent RA with articulating spacers and were divided according to the number of RAs performed by the surgeons: HV (≥14 RAs/year) or LV (<14 RAs/year). Rates of mechanical complications and reoperations were compared. Risk factors for mechanical complications were analyzed. Of the 203 patients, 105 and 98 were treated by two HV and six LV surgeons, respectively. The mechanical complication rate was lower in HV surgeons (3.8%) than in LV surgeons (36.7%) (p < 0.001). The reoperation rate for mechanical complications was lower in HV surgeons (0.9%) than in LV surgeons (24.5%) (p < 0.001). Additionally, 47.2% of patients required hinge knees after mechanical spacer failure. Medial proximal tibial angle < 87°, recurvatum angle > 5°, and the use of a tibial spacer without a cement stem extension were risk factors for mechanical complications. Based on these findings, we made the following three conclusions: (1) HV surgeons had a lower rate of mechanical complications and reoperation than LV surgeons; (2) mechanical complications increased the level of constraint in final revision knee arthroplasty; and (3) all surgeons should avoid tibial spacer varus malalignment and recurvatum deformity and always use a cement stem extension with a tibial spacer.

Limited medial posterior capsular release increases the intraoperative medial component gap while maintaining the joint varus angle at extension in posterior-stabilized total knee arthroplasty

PURPOSE

There is a lack of robust evidence for the magnitude of the effects of posterior capsular release (PCR) on intraoperative component gaps during total knee arthroplasty (TKA). The purpose of the present study was to quantify and compare the effects of partial versus full PCR on the intraoperative component gaps at various degrees of flexion during posterior-stabilized TKA.

METHODS

Full PCR was performed on 39 consecutive cases (full PCR group), and partial PCR (the medial side up to and including the intercondylar notch) was performed on the subsequent 39 consecutive cases (partial PCR group) during posterior-stabilized TKA using the measured resection technique for varus knee osteoarthritis. Medial component gaps and varus angles at 0°, 10°, 45°, 90°, and a maximum of flexion were measured with a tensor device before and after the PCR. Differences between the two groups in post-release medial component gap increase and post-release joint varus angle increase were assessed using a t test. Pre- to post-release medial component gaps and joint varus angles in each group were compared using a paired samples t test.

RESULTS

In both groups at 0° and 10° of flexion, post-release medial compartment gaps were significantly greater than pre-release gaps (all P < 0.001). At 45°, 90° and maximum flexion, the medial compartment gap increase did not exceed the minimal detectable change in either group. At 0° and 10° of flexion, there was no significant difference in post-release medial compartment gap change between the two groups. In the full PCR group, post-release joint varus angles at 0° of flexion were significantly greater than pre-release angles (P < 0.001), while there was no significant pre- and post-release difference in the partial PCR group. The change in post-release joint varus angles at 0° of flexion was significantly greater in the full PCR group than in the partial PCR group.

CONCLUSION

Both full and partial PCR show similar clinical usefulness for increasing the medial component gap at extension and reducing component gap mismatch. A partial PCR can be used to avoid increasing joint varus angles at 0° of flexion.

LEVEL OF EVIDENCE

Level 2 (prospective comparative study).

Catastrophic Mid-Flexion Instability After Avulsion Fractures of the Articular Capsule of the Femur and Tibia in a Patient With Posterior-Stabilized Total Knee Arthroplasty: A Case Report

Mid-flexion instability can be caused by patient-related, implant-related, or technique-specific factors and impairs the activities of daily living after total knee arthroplasty (TKA). In this study, we report a rare case of a patient with severe mid-flexion instability following tibial and femoral avulsion fractures after posterior-stabilized (PS) TKA for knee osteoarthritis. An 82-year-old female with bilateral knee osteoarthritis underwent staged bilateral TKA with a posterior-stabilized prosthesis. The course of the early postoperative period was good, and the patient was able to walk independently with a cane. Two months postoperatively, the patient fell and then experienced left knee pain and instability in the mid-flexion range. Radiographic images showed avulsion fractures of the articular capsule of the femur and tibia, and fluoroscopic examination showed severe posterior subluxation of the tibia between 40° and 60° of flexion. Conservative treatment with a functional knee brace and quadriceps training was initiated due to the patient's hesitation to undergo a second surgery; however, no improvement was observed. Eventually, revision surgery was planned three months after the fall incident (five months after the left primary TKA). At revision surgery, osteosynthesis of the tibial avulsion fracture and thickening of the PS insert did not sufficiently stabilize the instability, and revision TKA with a rotating-hinge prosthesis was needed. The postoperative course was uneventful, and she was able to walk with a cane within two weeks after revision TKA with no complaints of instability. Two years postoperatively, the patient recovered well and had no recurrence of instability, pain, or dysfunction. This case report shows that loss of support by the joint capsules due to avulsion fractures may cause significant anteroposterior instability in the mid-flexion position after posterior-stabilized TKA. In such a case, conservative treatment failed, and the revision of the rotating-hinge prosthesis provided stability and good improvement.

Evaluation of anterior translation in total knee arthroplasty utilizing stress radiographs

BACKGROUND

Flexion instability is a common cause for revision after total knee arthroplasty (TKA); however, little objective criteria exist to determine excessive laxity in flexion. This study sought to determine the reliability of stress radiographs for flexion laxity using manual stress as well as a commercially available flexion stress device, with the hypothesis that a commercially available force device would provide increased translation compared to manual stress, and radiographic measurements would be reproducible.

METHODS

Ten patients who previously underwent TKA with non-hinged components were prospectively and consecutively enrolled at a single center to undergo stress radiographs. Three lateral radiographs with the knee at 90° of flexion were obtained for each patient: rest, commercial stress device at 150N, and manual stress. Calibrated radiographs were evaluated by two raters, and inter-rater and intra-rater reliability were determined using intraclass correlation coefficients (ICC).

RESULTS

Ten patients (seven female) with mean age 72 (range 55-82) years and average duration from surgery 36 (range 12-96) months were evaluated. The commercial stress device provided significantly less anterior translation than manual stress (- 0.3 mm vs. 3.9 mm; p < 0.01). Two patients reported pain with use of the stress device. Inter-observer reliability of measurements was good for commercial stress (ICC = 0.86) and excellent for manual stress (ICC = 0.94). Eighty-five percent of measurements were within 1 mm between observers. Intra-observer reliability of measurements was good to excellent for both the stress device and manual stress.

CONCLUSIONS

Lateral stress radiographs may assist in the objective evaluation of flexion instability. A commercially available product provided less translation than manual stress; however, measurements were reliable and reproducible between observers. Further research is required to correlate translation with stress radiographs to patient outcomes following revision arthroplasty.

The indication for aseptic revision TKA does not influence 1-year outcomes: an analysis of 178 full TKA revisions from a prospective institutional registry

BACKGROUND AND PURPOSE

Outcomes following revision total knee arthroplasty (TKA) may depend on the indication for revision surgery. We compared pain, patient-reported outcome measures (PROMs), and patient satisfaction among different indications for an aseptic TKA revision.

PATIENTS AND METHODS

This was a retrospective study of prospective data from an institutional registry of 178 primary TKAs revised between 2012 and 2020. Patients were grouped by the main reason for their revision: loosening, malposition, instability, or stiffness. Pain during mobilization and at rest (NRS 0-10), physical function (KOOS-PS and KSS), and quality of life (EQ-5D) were surveyed preoperatively and at 2 months and 1 year postoperatively. Patient satisfaction was evaluated through questions related to knee function and their willingness to undergo the same surgery again at 1-year follow-up.

RESULTS

Pain and PROMs improved in all groups and did not differ statistically significantly between the 4 groups at 1-year follow-up, but equivalence for pain was not confirmed between groups. Overall, pain during mobilization improved by 2.4 (95% CI 1.9-3.0) at 1-year follow-up, which was both clinically and statistically significant. Improvements were seen within 2 months of surgery, with no further improvements seen 1 year postoperatively. Approximately 2/3 of patients reported that their knee function had improved and would undergo the same surgery again, at 1-year follow-up.

CONCLUSION

Statistically significant and clinically relevant improvements in pain and PROMs were seen in all 4 revision groups 1 year after revision TKA. These results may assist clinicians and patients during preoperative counselling.

Long-term outcomes of one single-design varus valgus constrained versus one single-design rotating hinge in revision knee arthroplasty after over 10-year follow-up

Background

The appropriate degree of constraint in knee prosthetic revision is unknown, necessitating the use of the lowest possible constraint. This study aimed to compare the long-term clinical and survival results of revision with rotation hinge knee (RHK) VS constrained condylar constrained knee (CCK) implants.

Methods

Overall, 117 revision case were prospectively reviewed and dividing into two groups based on the degree of constraint used, using only one prosthetic model in each group (61 CCK vs 56 RHK). All implants were evaluated for a minimum of 10 years. Survival of both implants at the end of follow-up, free from revision for any cause, aseptic loosening, and septic cause was compared.

Results

Better results were seen with use of the RHK in joint ranges of (p = 0.023), KSCS (p = 0.015), KSFS (p = 0.043), and KOOS (p = 0.031). About 22.2% of the cases required repeat surgery (11.7% RHK vs 29.6% CCK, p = 0.023). Constrained condylar implants had a significantly lower survival rates than rotating hinge implants (p = 0.005), due to a higher aseptic loosening rate (p = 0.031).

Conclusion

Using a specific RHK design with less rotational constraint has better clinical and survival outcomes than implants with greater rotational constraint, such as one specific CCK.