Immobilization of cellulase on a silica gel substrate modified using a 3-APTES self-assembled monolayer

Adhesion Strength Enhancement of Butyl Rubber and Aluminum Using Nanoscale Self-Assembled Monolayers of Various Silane Coupling Agents for Vibration Damping Plates

In this paper, we enhance the adhesion strength of butyl rubber-based vibrational damping plates using nanoscale self-assembled monolayers of various silane coupling agents. The silane coupling agents used to chemically modify the plate's aluminum surface include 3-aminopropyltriethoxysilane (APTES), (3-glycidyloxypropyl) triethoxysilane (GPTES), 3-mercaptopropyltrimethoxysilane (MPTMS), and 3-(triethoxysilyl)propyl isocyanate (ICPTES). The modified surfaces were analyzed using Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS), and the enhancement in adhesion strength between the rubber and aluminum was estimated through T-Peel tests. As a result, MPTMS showed the highest enhancement in adhesion strength, of approximately 220% compared to the untreated sample, while GPTES, ICPTES, and APTES resulted in adhesion strength enhancements of approximately 200%, 150%, and 130%, respectively.

Specific nanoprobe design for MRI: Targeting laminin in the blood-brain barrier to follow alteration due to neuroinflammation

Chronic neuroinflammation is characterized by increased blood-brain barrier (BBB) permeability, leading to molecular changes in the central nervous system that can be explored with biomarkers of active neuroinflammatory processes. Magnetic resonance imaging (MRI) has contributed to detecting lesions and permeability of the BBB. Ultra-small superparamagnetic particles of iron oxide (USPIO) are used as contrast agents to improve MRI observations. Therefore, we validate the interaction of peptide-88 with laminin, vectorized on USPIO, to explore BBB molecular alterations occurring during neuroinflammation as a potential tool for use in MRI. The specific labeling of NPS-P88 was verified in endothelial cells (hCMEC/D3) and astrocytes (T98G) under inflammation induced by interleukin 1β (IL-1β) for 3 and 24 hours. IL-1β for 3 hours in hCMEC/D3 cells increased their co-localization with NPS-P88, compared with controls. At 24 hours, no significant differences were observed between groups. In T98G cells, NPS-P88 showed similar nonspecific labeling among treatments. These results indicate that NPS-P88 has a higher affinity towards brain endothelial cells than astrocytes under inflammation. This affinity decreases over time with reduced laminin expression. In vivo results suggest that following a 30-minute post-injection, there is an increased presence of NPS-P88 in the blood and brain, diminishing over time. Lastly, EAE animals displayed a significant accumulation of NPS-P88 in MRI, primarily in the cortex, attributed to inflammation and disruption of the BBB. Altogether, these results revealed NPS-P88 as a biomarker to evaluate changes in the BBB due to neuroinflammation by MRI in biological models targeting laminin.

Immobilization and Characterization of a Processive Endoglucanase EG5C-1 from Bacillus subtilis on Melamine-Glutaraldehyde Dendrimer-Functionalized Magnetic Nanoparticles

Exploring an appropriate immobilization approach to enhance catalytic activity and reusability of cellulase is of great importance to reduce the price of enzymes and promote the industrialization of cellulose-derived biochemicals. In this study, Fe3O4 magnetic nanoparticles (MNPs) were functionalized with meso-2,3-dimercaptosuccinic acid to introduce carboxyl groups on the surface (DMNPs). Then, melamine-glutaraldehyde dendrimer-like polymers were grafted on DMNPs to increase protein binding sites for the immobilization of processive endoglucanase EG5C-1. Moreover, this dendrimer-like structure was beneficial to protect the conformation of EG5C-1 and facilitate the interaction between substrate and active center. The loading capacity of the functionalized copolymers (MG-DMNPs) for EG5C-1 was about 195 mg/g, where more than 90% of the activity was recovered. Immobilized EG5C-1 exhibited improved thermal stability and increased tolerability over a broad pH range compared with the free one. Additionally, MG-DMNP/EG5C-1 biocomposite maintained approximately 80% of its initial hydrolysis productivity after five cycles of usage using filter paper as the substrate. Our results provided a promising approach for the functionalization of MNPs, enabling the immobilization of cellulases with a high loading capacity and excellent activity recovery.

Anodic Aluminum Oxide-Based Chemi-Capacitive Sensor for Ethanol Gas

Alcohol ingested by humans can be analyzed via breath tests; however, approximately 1% can be excreted via the skin. In this paper, we present a capacitive sensor using hydrophobically treated anodic aluminum oxide (AAO) capable of detecting alcohol excreted through the epidermis. The degree of hydrophobicity based on the duration of exposure to 3-aminopropyltriethoxysilane vapor comprising a small number of Si-NH2 functional groups on the AAO surface was confirmed and the optimal exposure time was confirmed to be 60 min. The hydrophobized AAO showed a 4.8% reduction in sensitivity to moisture. Simultaneously, the sensitivity of the sensor to ethanol decreased by only 12%. Lastly, the fabricated sensor was successfully operated by attaching it to an ankle-type breathalyzer.

Facile Hydrogenolysis of Sugars to 1,2-Glycols by Ru@PPh3/OPPh3 Confined Large-Pore Mesoporous Silica

Tandem hydrogenation vis-à-vis hydrogenolysis of xylose to 1,2-glycols remains a major challenge. Although one-pot conversion of xylose to 1,2-glycols requires stringent conditions, a sustainable approach would be quite noteworthy. We have developed a microwave route for the one-pot conversion of pentose (C5) and hexose (C6) sugars into glycol and hexitol, without pressurized hydrogen reactors. A pronounced hydrogenolysis of sugars to glycols is observed by Ru single atom (SA) on triphenylphosphine/phosphine oxide-modified silica (Ru@SiP), in contrast to Ru SA on pristine (Ru@SiC) and 3-aminopropyl-modified silica (Ru@SiN). A promising "ligand effect" was observed through phosphine modification of silica that presents a 70% overall yield of all reduced sugars (xylitol + glycols) from a 99% conversion of xylose with Ru@SiP. A theoretical study by DFT depicts an electronic effect on Ru-SA by triphenylphosphine that promotes the catalytic hydrogenolysis of sugars under mild conditions. Hence, this research represents an important step for glycols from biomass-derived sources.

Cellulase immobilization to enhance enzymatic hydrolysis of lignocellulosic biomass: An all-inclusive review

Cellulase-mediated lignocellulosic biorefinery plays a crucial role in the production of high-value biofuels and chemicals, with enzymatic hydrolysis being an essential component. The advent of cellulase immobilization has revolutionized this process, significantly enhancing the efficiency, stability, and reusability of cellulase enzymes. This review offers a thorough analysis of the fundamental principles underlying immobilization, encompassing various immobilization approaches such as physical adsorption, covalent binding, entrapment, and cross-linking. Furthermore, it explores a diverse range of carrier materials, including inorganic, organic, and hybrid/composite materials. The review also focuses on emerging approaches like multi-enzyme co-immobilization, oriented immobilization, immobilized enzyme microreactors, and enzyme engineering for immobilization. Additionally, it delves into novel carrier technologies like 3D printing carriers, stimuli-responsive carriers, artificial cellulosomes, and biomimetic carriers. Moreover, the review addresses recent obstacles in cellulase immobilization, including molecular-level immobilization mechanism, diffusion limitations, loss of cellulase activity, cellulase leaching, and considerations of cost-effectiveness and scalability. The knowledge derived from this review is anticipated to catalyze the evolution of more efficient and sustainable biocatalytic systems for lignocellulosic biomass conversion, representing the current state-of-the-art in cellulase immobilization techniques.

Design of a 3D Amino-Functionalized Rice Husk Ash Nano-Silica/Chitosan/Alginate Composite as Support for Laccase Immobilization

Recycling of agro-industrial waste is one of the major issues addressed in recent years aimed at obtaining products with high added value as a future alternative to traditional ones in the per-spective of a bio-based and circular economy. One of the most produced wastes is rice husk and it is particularly interesting because it is very rich in silica, a material with a high intrinsic value. In the present study, a method to extract silica from rice husk ash (RHA) and to use it as a carrier for the immobilization of laccase from Trametes versicolor was developed. The obtained mesoporous nano-silica was characterized by X-ray diffraction (XRD), ATR-FTIR spectroscopy, Scanning Elec-tron Microscopy (SEM), and Energy Dispersive X-ray spectroscopy (EDS). A nano-silica purity of about 100% was found. Nano-silica was then introduced in a cross-linked chitosan/alginate scaffold to make it more easily recoverable after reuse. To favor laccase immobilization into the composite scaffold, functionalization of the nano-silica with (γ-aminopropyl) triethoxysilane (APTES) was performed. The APTES/RHA nano-silica/chitosan/alginate (ARCA) composite al-lowed to obtain under mild conditions (pH 7, room temperature, 1.5 h reaction time) a robust and easily reusable solid biocatalyst with 3.8 U/g of immobilized enzyme which maintained 50% of its activity after six reuses. The biocatalytic system, tested for syringic acid bioremediation, was able to totally oxidize the contaminant in 24 h.

Poly(levodopa)-Functionalized Polysaccharide Hydrogel Enriched in Fe3O4 Particles for Multiple-Purpose Biomedical Applications

In recent years, there has been a significant increase in interest in the use of curdlan, a naturally derived polymer, for medical applications. However, it is relatively inactive, and additives increasing its biomedical potential are required; for example, antibacterial compounds, magnetic particles, or hemostatic agents. The stability of such complex constructs may be increased by additional functional networks, for instance, polycatecholamines. The article presents the production and characterization of functional hydrogels based on curdlan enriched with Fe₃O₄ nanoparticles (NPs) or Fe₃O₄-based heterostructures and poly(L-DOPA) (PLD). Some of the prepared modified hydrogels were nontoxic, relatively hemocompatible, and showed high antibacterial potential and the ability to convert energy with heat generation. Therefore, the proposed hydrogels may have potential applications in temperature-controlled regenerative processes as well as in oncology therapies as a matrix of increased functionality for multiple medical purposes. The presence of PLD in the curdlan hydrogel network reduced the release of the NPs but slightly increased the hydrogel's hemolytic properties. This should be taken into account during the selection of the final hydrogel application.

Modified Activated Carbon: A Supporting Material for Improving Clostridium beijerinckii TISTR1461 Immobilized Fermentation

This study aimed to investigate the effect of activated carbon (AC) as an immobilization material in acetone-butanol-ethanol fermentation. The AC surface was modified with different physical (orbital shaking and refluxing) and chemical (nitric acid, sodium hydroxide and, (3-aminopropyl)triethoxysilane (APTES)) treatments to enhance the biobutanol production by Clostridium beijerinckii TISTR1461. The effect of surface modification on AC was evaluated using Fourier-transform infrared spectroscopy, field emission scanning electron microscopy, surface area analyses, and X-ray photoelectron spectroscopy, while the fermented broth was examined by high-performance liquid chromatography. The chemical functionalization significantly modified the physicochemical properties of the different treated ACs and further enhanced the butanol production. The AC treated with APTES under refluxing provided the best fermentation results at 10.93 g/L of butanol, 0.23 g/g of yield, and 0.15 g/L/h of productivity, which were 1.8-, 1.5-, and 3.0-fold higher, respectively, than that in the free-cell fermentation. The obtained dried cell biomass also revealed that the treatment improved the AC surface for cell immobilization. This study demonstrated and emphasized the importance of surface properties to cell immobilization.

COVID-19 Detection Using a 3D-Printed Micropipette Tip and a Smartphone

The COVID-19 pandemic has caused over 7 million deaths worldwide and over 1 million deaths in the US as of October 15, 2022. Virus testing lags behind the level or availability necessary for pandemic events like COVID-19, especially in resource-limited settings. Here, we report a low cost, mix-and-read COVID-19 assay using a synthetic SARS-CoV-2 sensor, imaged and processed using a smartphone. The assay was optimized for saliva and employs 3D-printed micropipette tips with a layer of monoclonal anti-SARS-CoV-2 inside the tip. A polymeric sensor for SARS-CoV-2 spike (S) protein (COVRs) synthesized as a thin film on silica nanoparticles provides 3,3',5-5'-tetramethylbenzidine responsive color detection using streptavidin-poly-horseradish peroxidase (ST-poly-HRP) with 400 HRP labels per molecule. COVRs were engineered with an NHS-PEG4-biotin coating to reduce nonspecific binding and provide affinity for ST-poly-HRP labels. COVRs binds to S-proteins with binding strengths and capacities much larger than salivary proteins in 10% artificial saliva-0.01%-Triton X-100 (as virus deactivator). A limit of detection (LOD) of 200 TCID50/mL (TCID50 = tissue culture infectious dose 50%) in artificial saliva was obtained using the Color Grab smartphone app and verified using ImageJ. Viral load values obtained in 10% pooled human saliva spiked with inactivated SARS-COV-2 virus gave excellent correlation with viral loads obtained from qPCR (p = 0.0003, r = 0.99).

Fabrication of TiO2 Spheres and a Visible Light Active α-Fe2O3/TiO2-Rutile/TiO2-Anatase Heterogeneous Photocatalyst from Natural Ilmenite

High-purity (98.8%, TiO₂) rutile nanoparticles were successfully synthesized using ilmenite sand as the initial titanium source. This novel synthesis method was cost-effective and straightforward due to the absence of the traditional gravity, magnetic, electrostatic separation, ball milling, and smelting processes. Synthesized TiO₂ nanoparticles were 99% pure. Also, highly corrosive environmentally hazardous acid leachate generated during the leaching process of ilmenite sand was effectively converted into a highly efficient visible light active photocatalyst. The prepared photocatalyst system consists of anatase-TiO₂/rutile-TiO₂/Fe₂O₃ (TF-800), rutile-TiO₂/Fe₂TiO₅ (TFTO-800), and anatase-TiO₂/Fe₃O₄ (TF-450) nanocomposites, respectively. The pseudo-second-order adsorption rate of the TF-800 ternary nanocomposite was 0.126 g mg^-1 min^-1 in dark conditions, and a 0.044 min^-1 visible light initial photodegradation rate was exhibited. The TFTO-800 binary nanocomposite adsorbed methylene blue (MB) following pseudo-second-order adsorption (0.224 g mg^-1 min^-1) in the dark, and the rate constant for photodegradation of MB in visible light was 0.006 min^-1. The prepared TF-450 nanocomposite did not display excellent adsorptive and photocatalytic performances throughout the experiment period. The synthesized TF-800 and TFTO-800 were able to degrade 93.1 and 49.8% of a 100 mL, 10 ppm MB dye solution within 180 min, respectively.

Mn-Containing Bioactive Glass-Ceramics: BMP-2-Mimetic Peptide Covalent Grafting Boosts Human-Osteoblast Proliferation and Mineral Deposition

The addition of Mn in bioceramic formulation is gaining interest in the field of bone implants. Mn activates human osteoblast (h-osteoblast) integrins, enhancing cell proliferation with a dose-dependent effect, whereas Mn-enriched glasses induce inhibition of Gram-negative or Gram-positive bacteria and fungi. In an effort to further optimize Mn-containing scaffolds' beneficial interaction with h-osteoblasts, a selective and specific covalent functionalization with a bioactive peptide was carried out. The anchoring of a peptide, mapped on the BMP-2 wrist epitope, to the scaffold was performed by a reaction between an aldehyde group of the peptide and the aminic groups of silanized Mn-containing bioceramic. SEM-EDX, FT-IR, and Raman studies confirmed the presence of the peptide grafted onto the scaffold. In in vitro assays, a significant improvement in h-osteoblast proliferation, gene expression, and calcium salt deposition after 7 days was detected in the functionalized Mn-containing bioceramic compared to the controls.

Co-immobilization of Cellulase and β-Glucosidase into Mesoporous Silica Nanoparticles for the Hydrolysis of Cellulose Extracted from Eriobotrya japonica Leaves

Fungal cellulases generally contain a reduced amount of β-glucosidase (BG), which does not allow for efficient cellulose hydrolysis. To address this issue, we implemented an easy co-immobilization procedure of β-glucosidase and cellulase by adsorption on wrinkled mesoporous silica nanoparticles with radial and hierarchical open pore structures, exhibiting smaller (WSN) and larger (WSN-p) inter-wrinkle distances. The immobilization was carried out separately on different vectors (WSN for BG and WSN-p for cellulase), simultaneously on the same vector (WSN-p), and sequentially on the same vector (WSN-p) in order to optimize the synergy between cellulase and BG. The obtained results pointed out that the best biocatalyst is that prepared through simultaneous immobilization of BG and cellulase on the same vector (WSN-p). In this case, the adsorption resulted in 20% yield of immobilization, corresponding to an enzyme loading of 100 mg/g of support. 82% yield of reaction and 72 μmol/min·g activity were obtained, evaluated for the hydrolysis of cellulose extracted from Eriobotrya japonica leaves. All reactions were carried out at a standard temperature of 50 °C. The biocatalyst retained 83% of the initial yield of reaction after 9 cycles of reuse. Moreover, it had better stability than the free enzyme mixture in a wide range of temperatures, preserving 72% of the initial yield of reaction up to 90 °C.

Mechano-chemical and biological energetics of immobilized enzymes onto functionalized polymers and their applications

Enzymes of commercial importance, such as lipase, amylase, laccase, phytase, carbonic anhydrase, pectinase, maltase, glucose oxidase etc., show multifunctional features and have been extensively used in several fields including fine chemicals, environmental, pharmaceutical, cosmetics, energy, food industry, agriculture and nutraceutical etc. The deployment of biocatalyst in harsh industrial conditions has some limitations, such as poor stability. These drawbacks can be overcome by immobilizing the enzyme in order to boost the operational stability, catalytic activity along with facilitating the reuse of biocatalyst. Nowadays, functionalized polymers and composites have gained increasing attention as an innovative material for immobilizing the industrially important enzyme. The different types of polymeric materials and composites are pectin, agarose, cellulose, nanofibers, gelatin, and chitosan. The functionalization of these materials enhances the loading capacity of the enzyme by providing more functional groups to the polymeric material and hence enhancing the enzyme immobilization efficiency. However, appropriate coordination among the functionalized polymeric materials and enzymes of interest plays an important role in producing emerging biocatalysts with improved properties. The optimal coordination at a biological, physical, and chemical level is requisite to develop an industrial biocatalyst. Bio-catalysis has become vital aspect in pharmaceutical and chemical industries for synthesis of value-added chemicals. The present review describes the current advances in enzyme immobilization on functionalized polymers and composites. Furthermore, the applications of immobilized enzymes in various sectors including bioremediation, biosensor and biodiesel are also discussed.

Facile Cellulase Immobilisation on Bioinspired Silica

Cellulases are enzymes with great potential for converting biomass to biofuels for sustainable energy. However, their commercial use is limited by their costs and low reusability. Therefore, the scientific and industrial sectors are focusing on finding better strategies to reuse enzymes and improve their performance. In this work, cellulase from Aspergillus niger was immobilised through in situ entrapment and adsorption on bio-inspired silica (BIS) supports. To the best of our knowledge, this green effect strategy has never been applied for cellulase into BIS. In situ entrapment was performed during support synthesis, applying a one-pot approach at mild conditions (room temperature, pH 7, and water solvent), while adsorption was performed after support formation. The loading efficiency was investigated on different immobilisation systems by Bradford assay and FTIR. Bovine serum albumin (BSA) was chosen as a control to optimize cellulase loading. The residual activity of cellulase was analysed by the dinitro salicylic acid (DNS) method. Activity of 90% was observed for the entrapped enzyme, while activity of ~55% was observed for the adsorbed enzyme. Moreover, the supported enzyme systems were recycled five times to evaluate their reuse potential. The thermal and pH stability tests suggested that both entrapment and adsorption strategies can increase enzyme activity. The results highlight that the entrapment in BIS is a potentially useful strategy to easily immobilise enzymes, while preserving their stability and recycle potential.

Evaluation of Amine Functionalized Thermal Power Plant Solid Waste for Industrial Wastewater Remediation

Micro/nanoparticles generated after the combustion of coal/lignite in the thermal power plants were modified with amino groups of (3-aminopropyl) triethoxysilane (APTES). These silane-based functional particles were applied in textile dye (xylenol orange, XO and methyl orange, MO) removal process to deal with an industrial wastewater problem. The maximum adsorption efficiencies of APTES coated micro/nanoparticles for MO and XO dye molecules were calculated to be around 98% and 75%, respectively. The adsorption behavior of the LCFA against dyes is also assessed by investigating the effect of adsorbent dosage, contact time, pH, and temperature. The optimum dye removal was observed at a pH of 4.0, and the equilibrium was achieved within 5 min. The maximum uptake capacities of LCFA-APTES for MO and XO dye molecules were calculated to be around 17.91 and 14.72 mg g−1, respectively. This value is approximately 3 − 5 times higher than the similar adsorbent in the literature. The uptake mechanism of MO and XO dyes onto LCFA-APTES is governed by electrostatic interaction and hydrogen bonding between dye molecules and APTES. The surface chemical modifications and the nature of functional groups were ascertained by scanning electron microscopy (SEM), thermogravimetric analysis (TGA), X-ray fluorescence (XRF), and X-ray photoelectron spectroscopy (XPS). The application of recovered micro/nanoparticles from solid wastes and their utilization for wastewater treatment is important not only for economy of developing countries but also for protecting the environment.

Frugal Approach toward Developing a Biomimetic, Microfluidic Network-on-a-Chip for In Vitro Analysis of Microvascular Physiology

Several disease conditions, such as cancer metastasis and atherosclerosis, are deeply connected with the complex biophysical phenomena taking place in the complicated architecture of the tiny blood vessels in human circulatory systems. Traditionally, these diseases have been probed by devising various animal models, which are otherwise constrained by ethical considerations as well as limited predictive capabilities. Development of an engineered network-on-a-chip, which replicates not only the functional aspects of the blood-carrying microvessels of human bodies, but also its geometrical complexity and hierarchical microstructure, is therefore central to the evaluation of organ-assist devices and disease models for therapeutic assessment. Overcoming the constraints of reported resource-intensive fabrication techniques, here, we report a facile, simple yet niche combination of surface engineering and microfabrication strategy to devise a highly ordered hierarchical microtubular network embedded within a polydimethylsiloxane (PDMS) slab for dynamic cell culture on a chip, with a vision of addressing the exclusive aspects of the vascular transport processes under medically relevant paradigms. The design consists of hierarchical complexity ranging from capillaries (∼80 μm) to large arteries (∼390 μm) and a simultaneous tuning of the interfacial material chemistry. The fluid flow behavior is characterized numerically within the hierarchical network, and a confluent endothelial layer is realized on the inner wall of microfluidic device. We further explore the efficacy of the device as a vascular deposition assay of circulatory tumor cells (MG-63 osteosarcoma cells) present in whole blood. The proposed paradigm of mimicking an in vitro vascular network in a low-cost paradigm holds further potential for probing cellular dynamics as well as offering critical insights into various vascular transport processes.

Development of a continuous-flow system with immobilized biocatalysts towards sustainable bioprocessing

Implementing immobilized biocatalysts in continuous-flow systems can enable a sustainable process through enhanced enzyme stability, better transport and process continuity as well as simplified recycle and downstream processing.

Adsorption of Cellulase on Wrinkled Silica Nanoparticles with Enhanced Inter-Wrinkle Distance

Mesoporous silica materials offer a unique opportunity for enzyme immobilization thanks to their properties, such as tuneable pore size, large surface area and easy functionalization. However, a significant enhancement of cellulase enzyme activity entrapped inside the silica pores still represents a challenge. In this work, we immobilized cellulase by adsorption on wrinkled silica nanoparticles (WSNs), obtaining an active and stable biocatalyst. We used pentanol as co-solvent to synthesize WSNs with enhanced inter-wrinkle distance in order to improve cellulase hosting. The physical-chemical and morphological characterization of WSNs and cellulase/WSNs was performed by thermogravimetric (TG), Fourier transform infrared (FT-IR), and transmission electron microscopy (TEM) analyses. The obtained results showed that this matrix generates a favourable microenvironment for hosting cellulase. The results of the catalytic assays and operational stability confirmed the key role of size, morphology and distribution of the pores in the successful outcome of the cellulase immobilization process. The immobilization procedure used allowed preserving most of the secondary structure of the enzyme and, consequently, its catalytic activity. Moreover, the same value of glucose yield was observed for five consecutive runs, showing a high operational stability of the biocatalyst.

Observation of Potential Contaminants in Processed Biomass Using Fourier Transform Infrared Spectroscopy

With rapidly increased interests in biomass, diverse chemical and biological processes have been applied for biomass utilization. Fourier transform infrared (FTIR) analysis has been used for characterizing different types of biomass and their products, including natural and processed biomass. During biomass treatments, some solvents and/or catalysts can be retained and contaminate biomass. In addition, contaminants can be generated by the decomposition of biomass components. Herein, we report FTIR analyses of a series of contaminants, such as various solvents, chemicals, enzymes, and possibly formed degradation by-products in the biomass conversion process along with poplar biomass. This information helps to prevent misunderstanding the FTIR analysis results of the processed biomass.

Immobilization of Cellulolytic Enzymes in Mesostructured Silica Materials

Mesostructured silica nanoparticles offer a unique opportunity in the field of biocatalysis thanks to their outstanding properties. The tunable pore size in the range of mesopores allows for immobilizing bulky enzyme molecules. The large surface area improves the catalytic efficiency by increasing enzyme loading and finely dispersing the biocatalyst molecules. The easily tunable pore morphology allows for creating a proper environment to host an enzyme. The confining effect of mesopores can improve the enzyme stability and its resistance to extreme pH and temperatures. Benefits also arise from other peculiarities of nanoparticles such as Brownian motion and easy dispersion. Fossil fuel depletion and environmental pollution have led to the need for alternative sustainable and renewable energy sources such as biofuels. In this context, lignocellulosic biomass has been considered as a strategic fuel source. Cellulases are a class of hydrolytic enzymes that convert cellulose into fermentable sugars. This review is intended to survey the immobilization of cellulolytic enzymes (cellulases and β-glucosidase) onto mesoporous silica nanoparticles and their catalytic performance, with the aim to give a contribution to the urgent action required against climate change and its impacts, by biorefineries’ development.

Dual-Functional, Superhydrophobic Coatings with Bacterial Anticontact and Antimicrobial Characteristics

Bacterial pathogens are responsible for millions of cases of illnesses and deaths each year throughout the world. The development of novel surfaces and coatings that effectively inhibit and prevent bacterial attachment, proliferation, and growth is one of the crucial steps for tackling this global challenge. Herein, we report a dual-functional coating for aluminum surfaces that relies on the controlled immobilization of lysozyme enzyme (muramidase) into interstitial spaces of presintered, nanostructured thin film based on ∼200 nm silica nanoparticles and the sequential chemisorption of an organofluorosilane to the available interfacial areas. The mean diameter of the resultant lysozyme microdomains was 3.1 ± 2.5 μm with an average spacing of 8.01 ± 6.8 μm, leading to a surface coverage of 15.32%. The coating had an overall root-mean-square (rms) roughness of 539 ± 137 nm and roughness factor of 1.50 ± 0.1, and demonstrated static, advancing, and receding water contact angles of 159.0 ± 1.0°, 155.4 ± 0.6°, and 154.4 ± 0.6°, respectively. Compared to the planar aluminum, the coated surfaces produced a 6.5 ± 0.1 (>99.99997%) and 4.0 ± 0.1 (>99.99%) log-cycle reductions in bacterial surfaces colonization against Gram-negative Salmonella Typhimurium LT2 and Gram-positive Listeria innocua, respectively. We anticipate that the implementation of such a coating strategy on healthcare environments and surfaces and food-contact surfaces can significantly reduce or eliminate potential risks associated with various contamination and cross-contamination scenarios.

Facile Synthesis of Graphene from Waste Tire/Silica Hybrid Additives and Optimization Study for the Fabrication of Thermally Enhanced Cement Grouts

This work evaluates the effects of newly designed graphene/silica hybrid additives on the properties of cementitious grout. In the hybrid structure, graphene nanoplatelet (GNP) obtained from waste tire was used to improve the thermal conductivity and reduce the cost and environmental impacts by using recyclable sources. Additionally, functionalized silica nanoparticles were utilized to enhance the dispersion and solubility of carbon material and thus the hydrolyzable groups of silane coupling agent were attached to the silica surface. Then, the hybridization of GNP and functionalized silica was conducted to make proper bridges and develop hybrid structures by tailoring carbon/silica ratios. Afterwards, special grout formulations were studied by incorporating these hybrid additives at different loadings. As the amount of hybrid additive incorporated into grout suspension increased from 3 to 5 wt%, water uptake increased from 660 to 725 g resulting in the reduction of thermal conductivity by 20.6%. On the other hand, as the concentration of GNP in hybrid structure increased, water demand was reduced, and thus the enhancement in thermal conductivity was improved by approximately 29% at the same loading ratios of hybrids in the prepared grout mixes. Therefore, these developed hybrid additives showed noticeable potential as a thermal enhancement material in cement-based grouts.

Kinetic and thermodynamic properties of purified alkaline protease from Bacillus pumilus Y7 and non-covalent immobilization to poly(vinylimidazole)/clay hydrogel

The characterization of the hydrogel was performed using Fourier‐transform infrared spectroscopy, X‐ray diffraction, and scanning electron microscopy. Purified Bacillus pumilus Y7‐derived alkaline protease was immobilized in Poly (vinylimidazole)/clay (PVI/SEP) hydrogel with 95% yield of immobilization. Immobilization decreased the pH optimum from 9 to 6 for free and immobilized enzyme, respectively. Temperature optimum 3°C decreased for immobilized enzyme. The K_m, V_m, and k_cat of immobilized enzyme were 4.4, 1.7, and 7.5‐fold increased over its free counterpart. Immobilized protease retained about 65% residual activity for 16^th reuse. The immobilized protease endured its 35% residual activity in the material after six cycle's batch applications. The results of thermodynamic analysis for casein hydrolysis showed that the ΔG^≠ (activation free energy) and ΔG^≠_E‐T (activation free energy of transition state formation) obtained for the immobilized enzyme decreased in comparison to those obtained for the free enzyme. On the other hand, the value of ΔG^≠_ES (free energy of substrate binding) was observed to have increased. These results indicate an increase in the spontaneity of the biochemical reaction post immobilization. Enthalpy value of immobilized enzyme that was 2.2‐fold increased over the free enzyme indicated lower energy for the formation of the transition state, and increased ΔS^≠ value implied that the immobilized form of the enzyme was more ordered than its free form.

A study on the enzymatic properties and reuse of cellulase immobilized with carbon nanotubes and sodium alginate

Cellulase has many potential applications in ethanol production, extraction of medicinal ingredients, food, brewing, oil exploration, environmental protection. However, the widespread use of cellulase is limited by its relatively high production costs and low biological activity. Therefore, we studied the enzymatic properties and reusability of cellulase immobilized on multiwalled carbon nanotubes and sodium alginate for the first time. The results showed that the optimum temperature and pH of immobilized cellulase was 40 °C and 3.0, respectively. After 1 month of storage at 4 °C, the enzyme activity of immobilized cellulase dropped to 71.2% of the baseline. Immobilized cellulase was proved to be reusable and maintained ~ 70% of its activity after 7 cycles of repeated use. Versus free cellulase, the immobilized cellulase showed good thermal stability, pH resistance, storage stability and reusability, which could be beneficial in large-scale industrial manufacturing processes.

Inulinase immobilization on polyethylene glycol/polypyrrole multiwall carbon nanotubes producing a catalyst with enhanced thermal and operational stability

This paper describes the development of a simple method for mixed non-covalent and covalent bonding of partially purified inulinase on functionalized multiwall carbon nanotubes (f-MWCNTs) with polypyrrole (PPy). The pyrrole (Py) was electrochemically polymerized on MWCNTs in order to fabricate MWCNTs/PPy nanocomposite. Two multiple forms of enzyme were bound to N-H functional groups from PPy and -COO^- from activated MWCNTs to yield a stable MWCNTs/PPy/PEG immobilized preparation with increased thermal stability. Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM) were used to confirm functionalization of nanoparticles and immobilization of the enzyme. The immobilization yield of 85% and optimal enzyme load of 345 μg protein onto MWCNTs was obtained. The optimum reaction conditions and kinetic parameters were established using the UV-Vis analytical assay. The best functional performance for prepared heterogeneous catalyst has been observed at pH 3.6 and 10, and at the temperatures of 60 and 80ºC. The half-life (t _1/2) of the immobilized inulinase at 60 and 80ºC was found to be 231 and 99 min, respectively. The reusability of the immobilized formulation was evaluated based on a method in which the enzyme retained 50% of its initial activity, which occurred after the eighteenth operation cycle.

Enantioselective resolution of 2-arylpropionic acid derivatives employing immobilization of lipase from Bacillus subtilis strain Kakrayal_1 (BSK-L)

This work studied the enantioselective resolution of 2-arylpropionic acid derivatives employing immobilization of lipase produced by Bacillus subtilis strain Kakrayal_1 (BSK-L). The efficient immobilization of lipase on modified silica gel was confirmed by Fourier transform infrared spectroscopy. Tethering of lipase facilitated the enhancement of physiochemical properties and stability of enzyme. Covalently immobilized enzyme retained 85% of residual activity even on reuse after 10th reaction cycle. Validation of immobilized lipase for enantioselective resolution of 2-arylpropionic acid derivatives led to 47.8% conversion efficiency with 87% enantiomeric excess (ee) for ketoprofen, and 27.3% conversion efficiency with 75% ee for flurbiprofen. The enantioselective resolution using immobilized lipase (BSK-L) was superior to free and commercially procured lipase, which suggest a potential application of immobilized lipase in the pharmaceutical/chemical industry.

Continuous flow biocatalysis

The continuous flow synthesis of active pharmaceutical ingredients, value-added chemicals, and materials has grown tremendously over the past ten years. This revolution in chemical manufacturing has resulted from innovations in both new methodology and technology. This field, however, has been predominantly focused on synthetic organic chemistry, and the use of biocatalysts in continuous flow systems is only now becoming popular. Although immobilized enzymes and whole cells in batch systems are common, their continuous flow counterparts have grown rapidly over the past two years. With continuous flow systems offering improved mixing, mass transfer, thermal control, pressurized processing, decreased variation, automation, process analytical technology, and in-line purification, the combination of biocatalysis and flow chemistry opens powerful new process windows. This Review explores continuous flow biocatalysts with emphasis on new technology, enzymes, whole cells, co-factor recycling, and immobilization methods for the synthesis of pharmaceuticals, value-added chemicals, and materials.

Starch Particles, Energy Harvesting, and the "Goldilocks Effect"

This study reports on the unique water vapor adsorption properties of biomass-derived starch particles (SPs). SPs offer an alternative desiccant for air-to-air energy exchangers in heating, ventilation, and air conditioning systems because of their remarkable adsorption-desorption performance. SP₁₅ has a particle diameter (d _p) of 15 μm with a surface area (SA) of 2.89 m²/g and a pore width (P _w) of 80 Å. Microporous starch particles (SP₁₅) were compared with high amylose starch (HAS₁₅; SA = 0.56 m²/g, d _p = 15 μm, P _w = 46 Å) and silica gel (SG₁₃; SA = 478 m²/g, d _p = 13 μm, P _w = 62 Å). Transient water vapor tests were performed using a customized small-scale energy exchanger coated with SP₁₅, HAS₁₅, and SG₁₃. The water swelling (%) for SP₁₅ was ca. 2 orders of magnitude greater with markedly higher (ca. three- and six-fold) water vapor uptake compared to HAS₁₅ and SG₁₃, respectively. At similar desiccant coating levels on the energy exchanger, the latent effectiveness of the SP₁₅ system was much improved (4-31%) over the HAS₁₅ and SG₁₃ systems at controlled operating conditions. SP₁₅ is a unique desiccant material with high affinity for water vapor and superior adsorption properties where ca. 98% regeneration was achieved under mild conditions. Therefore, SPs display unique adsorption-desorption properties, herein referred to as the "Goldilocks effect". This contribution reports on the utility of SPs as promising desiccant coatings in air-to-air energy exchangers for ventilation systems or as advanced materials for potential water/energy harvesting applications.

Biogenic porous silica and silicon sourced from Mexican Giant Horsetail (Equisetum myriochaetum) and their application as supports for enzyme immobilization

Porous silica-based materials are attractive for biomedical applications due to their biocompatibility and biodegradable character. In addition, inorganic supports such as porous silicon are being developed due to integrated circuit chip compatibility and tunable properties leading to a wide range of multidisciplinary applications. In this contribution, biosilica extracted from a rarely studied plant material (Equisetum Myriochaetum), its conversion to silicon and the potential for both materials to be used as supports for enzyme immobilization are investigated. E. myriochaetum was subject to conventional acid digestion to extract biogenic silica with a% yield remarkably higher (up to 3 times) than for other Equisetum sp. (i.e. E. Arvense). The surface area of the isolated silica was ∼400 m²/g, suitable for biotechnological applications. Biogenic silicon was obtained by magnesiothermic reduction. The materials were characterized by SEM-EDX, XRD, FT-IR, ICP-OES, TGA and BET analysis and did not contain significant levels of class 1 heavy elements (such as Pb, Cd, Hg and As). Two commercial peroxidases, horseradish peroxidase (HRP) and Coprinus cinereus peroxidase (CiP) were immobilized onto the biogenic materials using three different functionalization routes: (A) carbodiimide, (B) amine + glutaraldehyde and (C) amine + carbodiimide. Although both biogenic silica and porous silicon could be used as supports differences in behaviour were observed for the two enzymes. For HRP, loading onto biogenic silica via the glutaraldehyde immobilization technique (route B) was most effective. The loading of CiP showed a much higher peroxidase activity onto porous silicon than silica functionalized by the carbodiimide method (route A). From the properties of the extracted materials obtained from Equisetum Myriochaetum and the immobilization results observed, these materials appear to be promising for industrial and biomedical applications.

Bioactive polydimethylsiloxane surface for optimal human mesenchymal stem cell sheet culture

Human mesenchymal stem cell (hMSC) sheets hold great potential in engineering three-dimensional (3D) completely biological tissues for diverse applications. Conventional cell sheet culturing methods employing thermoresponsive surfaces are cost ineffective, and rely heavily on available facilities. In this study, a cost-effective method of layer-by-layer grafting was utilized for covalently binding a homogenous collagen I layer on a commonly used polydimethylsiloxane (PDMS) substrate surface in order to improve its cell adhesion as well as the uniformity of the resulting hMSC cell sheet. Results showed that a homogenous collagen I layer was obtained via this grafting method, which improved hMSC adhesion and attachment through reliable collagen I binding sites. By utilizing this low-cost method, a uniform hMSC sheet was generated. This technology potentially allows for mass production of hMSC sheets to fulfill the demand of thick hMSC constructs for tissue engineering and biomanufacturing applications.

Development of cellulase-nanoconjugates with enhanced ionic liquid and thermal stability for in situ lignocellulose saccharification

The present work aimed to improve catalytic efficiency of Trichoderma reesei cellulase for enhanced saccharification. The cellulase was immobilized on two nanomatrices i.e. magnetic and silica nanoparticles with immobilization efficiency of 85% and 76% respectively. The nanobioconjugates exhibited increase in V_max, temperature optimum, pH and thermal stability as compared with free enzyme. These could be efficiently reused for five repeated cycles and were stable in 1-ethyl-3-methylimidazoliumacetate [EMIM][Ac], an ionic liquid. Ionic liquids (IL) are used as green solvents to dissolve lignocellulosic biomass and facilitate better saccharification. The cellulase immobilized on magnetic nanoparticles was used for in situ saccharification of [EMIM][Ac] pretreated sugarcane bagasse and wheat straw for two cycles. The structural deconstruction and decrease in biomass crystallinity was confirmed by SEM, XRD and FTIR. The high hydrolysis yields (∼89%) obtained in this one-pot process coupled with IL stability and recycled use of immobilized cellulase, potentiates its usefulness in biorefineries.

Recycle of Immobilized Endocellulases in Different Conditions for Cellulose Hydrolysis

The immobilization of cellulases could be an economical alternative for cost reduction of enzyme application. The derivatives obtained in the immobilization derivatives were evaluated in recycles of paper filter hydrolysis. The immobilization process showed that the enzyme recycles were influenced by the shape (drop or sheet) and type of the mixture. The enzyme was recycled 28 times for sheets E' and 13 times for drops B'. The derivative E' showed the highest stability in the recycle obtaining 0.05 FPU/g, RA of 10%, and FPU Yield of 1.64 times, higher than FPU spent or Net FPU Yield of 5.3 times, saving more active enzymes. The derivative B showed stability in recycles reaching 0.15 FPU/g of derivative, yield of Recovered Activity (RA) of 25%, and FPU Yield of 1.57 times, higher than FPU spent on immobilization or Net PFU Yield of 2.81 times. The latex increased stability and resistance of the drops but did not improve the FPU/gram of derivative.

Intracellular redox induced drug release in cancerous and mesenchymal stem cells

In this report, we investigated intracellular redox induced drug release in cancerous cells and human mesenchymal stem cells (MSCs) as an example of healthy cells using redox-responsive microcapsules with covalently bonded anti-cancer drug (doxorubicin) via the amine-reactive cross-linker, 3,3'-dithiobis(sulfosuccinimidyl propionate) containing disulfide bond. Such rationally designed capsules with incorporated redox-sensitive cross-linker are capable of controllable Dox release in the presence of glutathione (GSH) due to a thiol-cleavable disulfide bonds. The treatment of human MSCs and human cervical cancer cell line (HeLa) with Dox-conjugated capsules showed that the Dox release was observed only when capsules incubated with HeLa cells which can be induced by high GSH level in cancerous (HeLa) cells. Moreover, the results of cell viability indicated that Dox-conjugated capsules are more effective when inducing cell death of HeLa than free Dox improving the anti-tumor efficacy of chemotherapeutic drug and simultaneously they possess lower cytotoxicity against MSCs compared to cancerous cells. Such properties are important in design of smart drug carriers for efficient cancer therapy.