Does maxillomandibular fixation affect skeletal stability following mandibular advancement? A single-blind clinical trial

A finite element analysis of stress distribution with various directions of intermaxillary fixation using orthodontic mini-implants and elastics following mandibular advancement with a bilateral sagittal split ramus osteotomy

OBJECTIVE

This finite element analysis (FEA) aimed to assess the stress distribution in the mandible and fixation system with various directions of the intermaxillary fixation (IMF) using mini-implants (MIs) and elastics following mandibular advancement with a bilateral sagittal split ramus osteotomy (BSSRO).

MATERIALS AND METHODS

A total of nine mandibular advancement models were set according to the position of the MIs (1.6 mm in diameter, 8 mm in length) and direction of the IMF elastics (1/4 inch, 5 oz). Major and minor principal stresses in the cortical and cancellous bones, von Mises stresses in the fixation system (miniplate and monocortical screws), and bending angles of the miniplate were analysed.

RESULTS

Compressive and tensile stress distributions in the mandible and von Mises stress distributions in the fixation system were greater in models with a Class III IMF elastic direction and a higher IMF elastic force than in models with a Class II IMF elastic direction and a lower IMF elastic force. The bending angle of the miniplate was negligible.

CONCLUSIONS

Stress distributions in the bone and fixation system varied depending on the direction, amount of force, and position of IMF elastics and MIs. Conclusively, IMF elastics in the Class II direction with minimal load in the area close to the osteotomy site should be recommended.

Redefining precision and efficiency in orthognathic surgery through virtual surgical planning and 3D printing: a narrative review

Orthognathic surgery, essential for addressing jaw and facial skeletal irregularities, has historically relied on traditional surgical planning (TSP) involving a series of time-consuming steps including two-dimensional radiographs. The advent of virtual surgical planning (VSP) and 3D printing technologies has revolutionized this field, bringing unprecedented precision and customization to surgical processes. VSP facilitates 3D visualization of the surgical site, allowing for real-time adjustments and improving preoperative stress for patients by reducing planning time. 3D printing dovetails with VSP, offering the creation of anatomical models and surgical guides, enhancing the predictability of surgical outcomes despite higher initial setup and material costs. The integration of VSP and 3D printing promises innovative and effective solutions in orthognathic surgery, surpassing the limitations of traditional methods. Patient-reported outcomes show a positive post-surgery impact on the quality of life, underlining the significant role of these technologies in enhancing self-esteem and reducing anxiety. Economic analyses depict a promising long-term fiscal advantage with these modern technologies, notwithstanding the higher initial costs. The review emphasizes the need for large-scale randomized controlled trials to address existing research gaps and calls for a deeper exploration into the long-term impacts and ethical considerations of these technologies. In conclusion, while standing on the cusp of a technological renaissance in orthognathic surgery, it is incumbent upon the medical fraternity to foster a collaborative approach, balancing innovation with scrutiny to enhance patient care. The narrative review encourages the leveraging of VSP and 3D printing technologies for more efficient and patient-centric orthognathic surgery, urging the community to navigate uncharted territories in pursuit of precision and efficiency in the surgical landscape.

Orthodontic-surgical treatment for severe skeletal class II malocclusion with vertical maxillary excess and four premolars extraction: A case report

BACKGROUND

Patient satisfaction with facial appearance at the end of orthodontic camouflage treatment is very important, especially for skeletal malocclusion. This case report highlights the importance of the treatment plan for a patient initially treated with four-premolar-extraction camouflage, despite indications for orthognathic surgery.

CASE SUMMARY

A 23-year-old male sought treatment complaining about his unsatisfactory facial appearance. His maxillary first premolars and mandibular second premolars had been extracted, and a fixed appliance had been used to retract his anterior teeth for two years without improvement. He had a convex profile, a gummy smile, lip incompetence, inadequate maxillary incisor inclination, and almost a class I molar relationship. Cephalometric analysis showed severe skeletal class II malocclusion (A point-nasion-B point = 11.5°) with a retrognathic mandible (sella-nasion-B point = 75.9°), a protruded maxilla (sella-nasion-A point = 87.4°), and vertical maxillary excess (upper incisor to palatal plane = 33.2 mm). The excessive lingual inclination of the maxillary incisors (upper incisor to nasion-A point line = -5.5°) was due to previous treatment attempts to compensate for the skeletal class II malocclusion. The patient was successfully retreated with decompensating orthodontic treatment combined with orthognathic surgery. The maxillary incisors were repositioned and proclined in the alveolar bone, the overjet was increased, and a space was created for orthognathic surgery, including maxillary impaction, anterior maxillary back-setting, and bilateral sagittal split ramus osteotomy to correct his skeletal anteroposterior discrepancy. Gingival display was reduced, and lip competence was restored. In addition, the results remained stable after 2 years. The patient was satisfied with his new profile as well as with the functional malocclusion at the end of treatment.

CONCLUSION

This case report provides orthodontists a good example of how to treat an adult with severe skeletal class II malocclusion with vertical maxillary excess after an unsatisfactory orthodontic camouflage treatment. Orthodontic and orthognathic treatment can significantly correct a patient’s facial appearance.

Surgical cutting guide and single plate fixation for intraoral vertical ramus osteotomy

With the advancement of digital technology over the last few decades, the use of virtual surgical planning and fabrication of surgical guides have tremendously improved the outcomes of various maxillofacial surgical procedures. The intraoral vertical ramus osteotomy (IVRO) is an orthognathic surgical procedure largely employed for mandibular setback in correcting dentofacial deformities. This study describes the design and application of a surgical cutting guide for IVRO. The guide can also be used to facilitate the placement of miniplate fixation. The initial experience at the authors' centre suggests that the guide has allowed the osteotomy to be performed with increased precision and confidence. Furthermore, the use of miniplate fixation decreased the period of maxillomandibular fixation. However, a larger series is required to evaluate the utility of this system more thoroughly.