Femoral placement of a totally implantable venous access port with spontaneous catheter fracture: case report

Totally implanted central venous access devices inserted by the femoral route: A narrative review and the proposal of a novel approach, the FICC-port

BACKGROUND

Femoral ports are used in patients with indication to a totally implanted venous access device but with contraindication to chest-ports and brachial ports because of obstruction of the superior vena cava. In the last three decades, femoral ports have been implanted almost exclusively by cannulation of the common femoral vein at the groin, while the position of the tip has been assessed by X-ray.

METHODS

We report our experience with a new approach to femoral ports, which includes recent methods and techniques developed in the last few years. These novel femoral ports, which we call "FICC-ports," are characterized by (a) long femoral 5 Fr polyurethane catheter inserted by ultrasound-guided puncture of the superficial femoral vein at mid-thigh; (b) intraprocedural location of the tip in the sub-diaphragmatic inferior vena cava, using ultrasound visualization by the transhepatic and/or the subcostal view; (c) low-profile or very low-profile reservoir implanted above the quadriceps muscle, at mid-thigh.

RESULTS

In the last 3 years, we have implanted 47 FICC-ports in young adults with mediastinal lymphoma compressing the superior vena cava. We had no immediate/early complication, and only three late complications (one kinking of the catheter in the subcutaneous tissue; one tip migration with secondary venous thrombosis; one persistent withdrawal occlusion due to fibroblastic sleeve).

CONCLUSION

If there is indication to a femoral port, the implantation of a "FICC-port"-as described above-is to be strongly considered in terms of safety, effectiveness, and cost-effectiveness: no immediate-early complications, minimal late complications, no X-ray exposure, low invasiveness, low cost.

Comparative structural analysis of polyurethane and silicone catheters of totally implantable venous access devices by micro-computed tomography

Objectives:

To investigate microstructural alterations of explanted long-term central venous catheters of totally implantable venous access devices, using micro-computed tomography.

Methods:

A total of 16 catheters (9 made of silicone and 7 made of polyurethane), all non-fractured, have been analyzed in this study. Eight catheters were implanted for an average duration of 994 days (min–max: 98–2731 days), while the remaining eight catheters (four for each material, forming the SIref and PUref control groups) were analyzed before implant and used as a reference. X-ray micro-computed tomography was used to reconstruct the three-dimensional geometry of selected segments of each catheter (ca. 10 cm per sample).

Results:

Morphometric analysis of the catheters revealed increases wall thickness and section area in the polyurethane group as compared with the reference central venous catheters of the same materials (wall thickness: 403 ± 12 μm in the polyurethane (PU) group vs 382 ± 4 μm in PUref, p = 0.014; wall cross-section area: 2.04 ± 0.09 mm² in PU vs 1.91 ± 0.03 mm² in PUref, p = 0.04), whereas implanted silicone catheters showed a larger luminal cross section as compared with their controls (lumen cross-section area = 0.851 ± 0.020 mm² in silicone (SI) group vs 0.811 ± 0.007 mm² in SIref, p = 0.007). All analyzed samples in this study presented some type of alteration in the catheter walls, namely, hyperdense spots (below 0.1 mm size), air gaps/bubbles and displacements of inner and outer axes causing heterogeneous wall thickness. The incidence of air gaps showed no difference with respect to both material type and duration of implant, whereas the SI group revealed more hyperdense spots as compared to all other groups.

Conclusion:

Morphological change and local structural alteration can occur in both silicone and polyurethane catheters. This evidence suggests the need for further studies connecting those morphological changes with modification of mechanical robustness, which ultimately can play a role for patient safety.