Exploring the role of transtibial prosthetic use in deep tissue injury development: a scoping review

Application of ultrasound to monitor in vivo residual bone movement within transtibial prosthetic sockets

Transtibial prosthetic users do often struggle to achieve an optimal prosthetic fit, leading to residual limb pain and stump-socket instability. Prosthetists face challenges in objectively assessing the impact of prosthetic adjustments on residual limb loading. Understanding the mechanical behaviour of the pseudo-joint formed by the residual bone and prosthesis may facilitate prosthetic adjustments and achieving optimal fit. This study aimed to assess the feasibility of using B-mode ultrasound to monitor in vivo residual bone movement within a transtibial prosthetic socket during different stepping tasks. Five transtibial prosthesis users participated, and ultrasound images were captured using a Samsung HM70A system during five dynamic conditions. Bone movement relative to the socket was quantified by tracking the bone contour using Adobe After-Effect. During the study a methodological adjustment was made to improve data quality, and the first two participants were excluded from analysis. The remaining three participants exhibited consistent range of motion, with a signal to noise ratio ranging from 1.12 to 2.59. Medial-lateral and anterior-posterior absolute range of motion varied between 0.03 to 0.88 cm and 0.14 to 0.87 cm, respectively. This study demonstrated that it is feasible to use B-mode ultrasound to monitor in vivo residual bone movement inside an intact prosthetic socket during stepping tasks.

Quantifying Bone and Skin Movement in the Residual Limb-Socket Interface of Individuals With Transtibial Limb Loss Using Dynamic Stereo X-Ray: Protocol for a Lower Limb Loss Cadaver and Clinical Study

BACKGROUND

Relative motion between the residual limb and socket in individuals with transtibial limb loss can lead to substantial consequences that limit mobility. Although assessments of the relative motion between the residual limb and socket have been performed, there remains a substantial gap in understanding the complex mechanics of the residual limb-socket interface during dynamic activities that limits the ability to improve socket design. However, dynamic stereo x-ray (DSX) is an advanced imaging technology that can quantify 3D bone movement and skin deformation inside a socket during dynamic activities.

OBJECTIVE

This study aims to develop analytical tools using DSX to quantify the dynamic, in vivo kinematics between the residual limb and socket and the mechanism of residual tissue deformation.

METHODS

A lower limb cadaver study will first be performed to optimize the placement of an array of radiopaque beads and markers on the socket, liner, and skin to simultaneously assess dynamic tibial movement and residual tissue and liner deformation. Five cadaver limbs will be used in an iterative process to develop an optimal marker setup. Stance phase gait will be simulated during each session to induce bone movement and skin and liner deformation. The number, shape, size, and placement of each marker will be evaluated after each session to refine the marker set. Once an optimal marker setup is identified, 21 participants with transtibial limb loss will be fitted with a socket capable of being suspended via both elevated vacuum and traditional suction. Participants will undergo a 4-week acclimation period and then be tested in the DSX system to track tibial, skin, and liner motion under both suspension techniques during 3 activities: treadmill walking at a self-selected speed, at a walking speed 10% faster, and during a step-down movement. The performance of the 2 suspension techniques will be evaluated by quantifying the 3D bone movement of the residual tibia with respect to the socket and quantifying liner and skin deformation at the socket-residuum interface.

RESULTS

This study was funded in October 2021. Cadaver testing began in January 2023. Enrollment began in February 2024. Data collection is expected to conclude in December 2025. The initial dissemination of results is expected in November 2026.

CONCLUSIONS

The successful completion of this study will help develop analytical methods for the accurate assessment of residual limb-socket motion. The results will significantly advance the understanding of the complex biomechanical interactions between the residual limb and the socket, which can aid in evidence-based clinical practice and socket prescription guidelines. This critical foundational information can aid in the development of future socket technology that has the potential to reduce secondary comorbidities that result from complications of poor prosthesis load transmission.

INTERNATIONAL REGISTERED REPORT IDENTIFIER (IRRID)

DERR1-10.2196/57329.

An ex vivo animal model to study the effect of transverse mechanical loading on skeletal muscle

In many populations like wheelchair and prosthetic users, the soft tissue is subject to excessive or repetitive loading, making it prone to Deep Tissue Injury (DTI). To study the skeletal muscle response to physical stress, numerous in vitro and in vivo models exist. Yet, accuracy, variability, and ethical considerations pose significant trade-offs. Here, we present an ex vivo approach to address these limitations and offer additional quantitative information on cellular damage. In this study, skeletal muscle tissue from Sprague Dawley rats was isolated and transversely loaded. Histological analysis and fluorescence staining demonstrated that the setup was suitable to keep the tissue alive throughout the experimental procedure. Mechanically induced cell damage was readily distinguishable through morphological changes and uptake of a membrane impermeable dye. Our comparably simple experimental setup can be adapted to different loading conditions and tissues to assess the cell response to mechanical loading in future studies.

Methodology to Investigate Effect of Prosthetic Interface Design on Residual Limb Soft Tissue Deformation

BACKGROUND

Residual limb discomfort and injury is a common experience for people living with lower limb amputation. Frequently, inadequate load distribution between the prosthetic device and the residual limb is the root cause of this issue. To advance our understanding of prosthetic interface fit, tools are needed to evaluate the mechanical interaction at the prosthetic interface, allowing interface designs to be evaluated and optimised.

OBJECTIVE

Present a methodology report designed to facilitate comprehension of the mechanical interaction between the prosthetic interface and the residual limb. As a pilot study, this methodology is used to compare a hands-on and hands-off interface for a single transtibial prosthesis user using secondary Magnetic Resonance Imaging (MRI) data.

METHODOLOGY

MRI data of the residual limb while wearing a prosthetic interface is segmented into a hard tissue and a skin surface model. These models are exported as stereolithography (STL) files. Two methods are used to analyse the interface designs. Firstly, CloudCompare software is used to compute the nearest vertex on the skin surface for every vertex on the compiled internal bony surface for both interface types. Secondly, CloudCompare software is used to compare registered skin surfaces of the residual limb while wearing the hands-on and hands-off interfaces.

FINDINGS

The maximum and minimum nearest distances between the internal bony surface and skin surface were similar between interface types. However, the distribution of nearest distances was different. When comparing the skin surface while wearing both interfaces, where the fit is more compressive can be visualized. For the dataset used in this study, the classic features of a hands-on Patella Tendon Bearing interface and hands-off pressure cast interface could be identified.

CONCLUSION

The methodology presented in this report may give researchers a further tool to better understand how interface designs affect the soft tissues of the residual limb.

Soft robotics-inspired sensing system for detecting downward movement and pistoning in prosthetic sockets: A proof-of-concept study

BACKGROUND

Vertical displacement of the residual limb within transtibial prosthetic socket, often known as "pistoning" or downward movement, may lead to skin breakdowns and ulcers. Downward movement is particularly difficult to self-manage for diabetic individuals living with amputation because of diminished sensation in the residual limb from peripheral neuropathy. Therefore, a customizable sensor at the distal end that can alert the users when high-risk downward movement and pistoning occurs is urgently needed.

OBJECTIVES

Presented herein for the first time is a lightweight, inexpensive sensing system inspired by soft robotics that can detect the occurrence and severity of downward movement at the distal end.

METHODS

The sensing system consists of a multilayered torus-shaped balloon, allowing easy integration with pin-lock socket systems. The design allows sensing of vertical displacement without imparting high reaction forces back onto the distal end. A benchtop compression tester was used to characterize system performance. Systematic and parametric benchtop tests were conducted to examine the sensor's physical characteristics. Long-term (24-h) stability of the sensor was also recorded.

RESULTS

Compared with water, air was determined to be a better medium with a higher linear full-scale span (FSS) because of its compressible nature. Repeatable 0.5-mm vertical displacements yielded a linear (>0.99 R2) FSS of 4.5 mm and a sensitivity of 0.8 kPa/mm. The sensing system is highly precise, with as low as 1% FSS total error band and average hysteresis of 2.84% of FSS. Over 24 h, a 4% FSS drift was observed.

CONCLUSION

Sensing system characteristics, coupled with low-cost, customizable fabrication, indicates promising performance for daily use to notify and alert transtibial prosthetic users of downward movement and/or pistoning.

Volume Fluctuations in Active and Nonactive Transtibial Prosthetics Users

This study aims to evaluate the validity and reliability of the Biosculptor’s Bioscanner system in capturing transtibial residual limb volume fluctuations in active and nonactive amputees during walking activity. Residual limb volume was obtained by measuring the limb circumference after amputees walked for 5 to 25 minutes for five consecutive days. The comparison of mean circumference between Bioscanner and manual measurements (i.e., tape measure) showed that the Bioscanner gave a higher estimation of circumference for the different amputees. Short-term changes in girth and volume due to an activity such as walking do not fluctuate uniformly. The results reflected as such as nonconsistence circumference change identified at different locations of the circumference profiles. Both amputees experienced a significant increase in circumference at the distal end of the limbs after 5 minutes of walking (7.35% change in nonactive and 8.83% in active amputees), and the measurement decreased as amputees walked longer. At 4-8 cm below the mid-patella tendon (pressure tolerant areas), both amputees experienced minor changes in the size of their circumference. The residual limb volume calculation resulted in the percentage difference between the two methods ranging from 2.4% to 9.3%. Pearson coefficient correlation obtained showed a high correlation between the two techniques, ranging from 0.97 to 1. The analysis of the limit of agreements showed that the majority of measurements were closed to the mean, suggesting that Bioscanner and manual techniques may be interchangeable and agree with one another. This study has implied that Bioscanner is comparable to the standard measurement method and may serve as an alternative tool in managing daily residual limb volume change.

Analysis of lower limb prosthetic socket interface based on stress and motion measurements

The study was designed to establish a biomechanical assessment platform for the lower limb residuum/socket interface as a function of duration and speed of movement. The approach exploits an interface sensor which measures multi-directional stresses at the interface. The corresponding interface coupling motion was assessed using a 3D motion capture system. A longitudinal study, involving a trans-femoral amputee, was conducted with nine repeated level walking sessions over a 12-month period. The effect of walking speed on interface biomechanics was also assessed. Interface peak pressures and shear stresses in the range of 55–59 kPa and 12–19 kPa were measured, respectively, over all sessions in the 12 months study period at the posterior-proximal location of the residuum. The peak pressure and longitudinal shear values were found to fluctuate approximately 11% and 40% as against its maximum value, respectively, over 12 months. In addition, up to 12° of angular coupling and up to 28 mm of pistoning were recorded over a gait cycle, which was found to change by 29% and 45% respectively over the study period. The variation in walking speed, by altering self-selected cadence, resulted in changes of pressure and shear stresses at mid-stance of the gait cycle. In particular, as compared with self-selected cadence, for fast speed, peak pressure and peak longitudinal shear stress decreased by 5% and 33%, respectively. For slow speed, peak pressure and peak longitudinal shear stress increased by 7% and 17%, respectively. The corresponding angular and pistoning revealed a variation of up to 29% and 45%, respectively. This biomechanical assessment approach shows promise in the quantitative assessment of interface kinematics and kinetics for lower limb prosthetics, the usage of which could assist the clinical assessment of prosthetic socket fit.

Air microfluidics-enabled soft robotic transtibial prosthesis socket liner toward dynamic management of residual limb contact pressure and volume fluctuation

Residual limb volume fluctuation and the resulting contact pressures are some of the key factors leading to skin ulcerations, suboptimal prosthetic functioning, pain, and diminishing quality of life of transtibial amputees. Self-management of socket fit is complicated by peripheral neuropathy, reducing the perception of pressure and pain in the residual limb. We introduce a novel proof-of-concept for a transtibial prosthetic socket liner with the potential to dynamically adjust the fit between the limb and socket. The core of the technology is a small air microfluidic chip (10 cm3 and 10 g) with 10 on-chip valves that enable sequential pressurizing of 10 actuators in custom sizes to match the pressures required by the residual limb's unique anatomy. The microfluidic chip largely reduced the number of electromechanical solenoid valves needed for sequential control of 10 actuators (2 instead of 10 valves), resulting in the reduction of the required power, size, mass, and cost of the control box toward an affordable and wearable prosthetic socket. Proof-of-concept testing demonstrated that the applied pressures can be varied in the desired sequence and to redistribute pressure. Future work will focus on integrating the system with biofidelic prosthetic sockets and residual limb models to investigate the ability to redistribute pressure away from pressure-sensitive regions (e.g., fibular head) to pressure tolerant areas. Overall, the dynamic prosthesis socket liner is very encouraging for creating a dynamic socket fit system that can be seamlessly integrated with existing socket fabrication methods for managing residual limb volume fluctuations and contact pressure.

The Impact of Limited Prosthetic Socket Documentation: A Researcher Perspective

The majority of limb prostheses are socket mounted. For these devices, the socket is essential for adequate prosthetic suspension, comfort, and control. The socket is unique among prosthetic components as it is not usually mass-produced and must instead be custom-made for individual residual limbs by a prosthetist. The knowledge of what constitutes "good" socket fit is gained by expert prosthetists and technicians over years of experience, and rarely documented. The reliance on tacit knowledge makes it difficult to standardize the criteria for a well-fitting socket, leading to difficulties understanding the impact of socket fit. Despite its importance, the workflow for socket fitting is often overlooked in literature. Due to the customized nature of sockets, if information is provided in literature, generally only the type of socket and suspension mechanism is noted, with information regarding the fitting and manufacturing processes omitted. In this article, the concerns, issues and consequences arising from lack of upper and lower limb socket documentation are discussed from a researcher perspective, supported by healthcare professionals and socket fabrication specialists. Key changes are proposed to the way socket manufacturing and evaluation are documented to assist future research.

Residual limb shear strain during gait is correlated with patient reported outcomes for persons with transfemoral amputation

The purpose of this study was to measure residual limb skin strain and strain rate within the socket during gait in individuals with a transfemoral amputation and to determine if skin strain during gait is related to patient-reported comfort and function. It was hypothesized that greater skin strain and skin strain rate would correlate to worse patient-reported outcomes. It was also hypothesized that skin strain would progressively increase from the distal to the proximal end of the residuum and maximum strain would occur shortly after heel strike. Dynamic biplane radiography (DBR), combined with conventional motion capture, was used to measure skin deformation within the socket during treadmill walking for 10 persons with unilateral transfemoral amputation. The questionnaire for persons with a transfemoral amputation (Q-TFA) was administered to assess prosthetic use, mobility, health problems, and global health. Q-TFA Prosthetic Use score and Problem score were negatively correlated with the peak shear strains in the proximal and distal regions of the residuum, respectively. Maximum shear strain increased progressively from proximal to distal regions of the residual limb. Within-subject variability in shear strain waveforms during gait was 0.7% or less, but between-subject variability was 3.3% to 5.0% shear. This study demonstrates that skin shear within the socket of persons with transfemoral amputation can be measured during gait using DBR and the results suggest that greater skin shear in the proximal region of the socket is related to decreased prosthetic use.