Characterization of reservoir-type microcapsules made by the solvent exchange method

In Situ Gel Formation in Microporated Skin for Enhanced Topical Delivery of Niacinamide

Although used widely in cosmetic formulations, topical delivery of niacinamide (LogP = -0.35) is unfavorable by conventional means. Poly(lactide-co-glycolide) (PLGA) formulations, can undergo a sol-gel transition triggered by solvent exchange, entrapping molecules and sustaining their release. The current study aims to exploit the ability of PLGA to gel in situ and enhance the topical delivery of niacinamide in microporated skin. In vitro drug permeation studies were performed using vertical Franz diffusion cells. Microporation was performed using Dr. Pen^TM Ultima A6, where pre-treatment with a 1 mm needle-length for 10 s and a 0.5 mm needle-length for 5 s, both at 13,000 insertions/min were compared. The effect of different grades of PLGA, EXPANSORB^® DLG 50-2A ("low" molecular weight), and EXPANSORB^® DLG 50-8A ("high" molecular weight) on topical delivery was also determined. Formulations containing PLGA resulted in successful gelation in situ on application over microporated skin. A significantly higher amount of drug was found in the skin with the 0.5 mm treatment for 5 s (892 ± 36 µg/cm²) than with 1 mm for 10 s (167 ± 16 µg/cm²). Hence, the different grades of PLGA were evaluated with 0.5 mm, 5 s treatment, and a significantly larger amount was seen in skin with the higher rather than the lower molecular weight polymer (172 ± 53 µg/cm²).

BSA-FITC-loaded microcapsules for in vivo delivery

Here we describe the preparation of BSA-FITC-loaded microcapsules as a model protein system for in vivo delivery. BSA-FITC-loaded microcapsules were prepared using a mono-axial nozzle ultrasonic atomizer, varying a number of parameters to determine optimal conditions. The preparation method chosen resulted in a BSA-FITC encapsulation efficiency of approximately 60% and a particle size of approximately 50 microm. An analysis of the microcapsules showed a BSA-FITC core surrounded by a poly(D,L-lactic-co-glycolic acid) (PLGA) shell. Injection of BSA-FITC-loaded microcapsules into rats resulted in a sustained release of BSA-FITC that maintained increased concentrations of BSA-FITC in plasma for up to 2 weeks. In contrast, the concentration of BSA-FITC in plasma after injection of BSA-FITC-only solution reached near-zero levels within 3 days. Fluorescence images of microcapsules removed at various times after implantation showed a gradual decrease of BSA-FITC in BSA-FITC-loaded microcapsules, confirming a sustained in vivo release of BSA-FITC. The duration of in vivo release and plasma concentration of BSA-FITC was correlated with the initial dose of BSA-FITC. BSA-FITC-loaded microcapsules maintained their structure for at least 4 weeks in the rat. The inflammatory response observed initially after injection declined over time. In conclusion, BSA-FITC-loaded microcapsules achieved sustained release of BSA-FITC, suggesting that microcapsules manufactured as described may be useful for in vivo delivery of pharmacologically active proteins.

Encapsulation of indomethacin using coaxial ultrasonic atomization followed by solvent evaporation

We have encapsulated indomethacin into poly (lactide-co-glycolide) (PLGA) using coaxial ultrasonic atomization technique. The specific aims of this study were to evaluate the effect of drug loading and a change in relative concentration of polymer in the inner and outer layers of coflowing spray liquids on the physicochemical characteristics of the particles. Indomethacin, a non steroidal anti-inflammatory drug, was selected as a model compound. The micro/nanocapsules prepared using a drug free PLGA solution as an outer layer showed higher encapsulation efficiency. Thermal analysis of the formulations indicated that indomethacin was dissolved within the PLGA matrix. The formulations prepared with 25 mg indomethacin showed relatively smaller particle size compared with the formulations prepared with 50 mg indomethacin. The particles, in general, showed bi- and tri-modal distribution. Irrespective of the compositions of the liquids 1 and 2, all the particles were smooth and spherical. A cross-section view of the particles revealed the presence of three different internal morphologies. These formulations were a mixture of hollow or solid spheres, and single or multiple spheres encapsulated into a larger sphere. To the best of our knowledge, this is the first study revealing the cross-sectional view of particles prepared with coaxial ultrasonic atomization technique.

Biodegradable microparticles and fiber fabrics for sustained delivery of cisplatin to treat C6 glioma in vitro

The duration of cisplatin release from most of the drug delivery devices seemed to be shorter than 14 days except large microparticles. The objective of this study was to fabricate and characterize cisplatin-loaded PLA microparticles, PLA/PLGA (30/70) composite microparticles, and fibers as formulations for long-term sustained delivery of cisplatin to treat C6 glioma in vitro by electrospray and electrospinning techniques. Cisplatin-loaded biodegradable microparticles with particle size of around 5 microm and fiber fabrics with diameter of 0.5-1.7 microm were obtained using electrospray and electrospinning techniques. Encapsulation efficiency and in vitro release of formulations were measured by ICP-OES. The encapsulation efficiency for different samples of microparticles was approximately from 33% to 72% and the fiber fabrics had encapsulation efficiency greater than 90%. Cisplatin-loaded microparticles showed typical characteristics of cisplatin release profile: a large initial burst followed by a sustained slow release of 35 days. The composite PLA/PLGA (30/70) microparticles could reduce the initial burst release of cisplatin because of their core-shell structures. In contrast, more than 75 days sustained release could be achieved by fiber fabric formulations without large initial burst. MTT assay was used to quantify the cytotoxicity of different formulations against C6 glioma cells. Microparticle formulations had slightly higher cytotoxicity than free drug. In contrast, the cytotoxicity of fiber fabrics formulation was around 4 times higher than of the free drug based on the actual amount of drug released. The microparticle and fiber fabric formulations presented may be promising for the sustained delivery of cisplatin to eliminate the undesired side effects caused by direct injection of cisplatin solution in systemic administration.

A new microencapsulation method using an ultrasonic atomizer based on interfacial solvent exchange

Reservoir-type microcapsules were produced in a mild and highly efficient manner using a coaxial ultrasonic atomizer. To understand the microencapsulation mechanism, the atomizer was operated in different modes. The results suggested the reservoir-type microcapsules were formed by midair collision of the microdrops of the two component liquids consisting of a polymer solution and an aqueous solution. The encapsulation efficiency and the distribution of the microdrops captured in midair were dependent on the ratio of the flow rates of the two liquids, which suggested that the collision involved multiple microdrops. This method allowed lysozyme to be encapsulated without loss of functional integrity and to be released with near zero-order kinetics for over 50 days. The ultrasonic atomizer provided a new method of preparing reservoir-type microcapsules.