Long-Acting Injectable Aqueous Suspensions-Summary From an AAPS Workshop

Temperature mapping of milling by dual centrifugation: A systematic investigation

Using low quantities of drug compounds is often favorable in the early stages of drug development, especially for what require a large screening investigation to define the final formulation composition, such as nano- and microsuspensions. For that reason, the dual centrifugation approach has in the recent years been used due to its reproducible and fast-milling capacity with 40 samples in 2 mL vials simultaneously without the addition of cooling breaks due to a built-in cooling system. Nonetheless, heat can be dissipated into the samples during high-intensity milling, resulting in increased sample temperatures that potentially can affect thermolabile compounds and potential influence the obtained suspensions in the screening experiments if the used stabilizer has temperature dependent variations in the performance. Hence, a systematic investigation of the influence of different process parameters on the heat dissipation in samples during milling by the dual centrifugation approach was performed in the present study. It was found that the milling speed had the highest impact on the final sample temperature, but also other parameters, such as the bead loading, bead size, and placement in the centrifuge during milling had significantly influenced the final mean temperature of the milling media. Higher temperatures were obtained with higher bead loadings, i.e., 3000 mg milling beads/mL and milling speeds (1500 rpm), and when smaller milling beads, i.e., 0.1 mm, were used during production. The study further showed that higher temperatures were measured for samples located on the bottom disk during milling, and also when located on the outer placement on the sample disk. Upscale investigations showed immensely increased sample temperatures (almost up to boiling point) when samples were prepared under similar formulation parameters and milling speed as small-volume vials. Furthermore, the study indicated that the addition of drug compounds during suspension preparation decreased the final sample temperature compared to samples that only contained purified water due to energy absorption of the drug compound.

The Langmuir-Blodgett trough (Langmuir film balance) can be used to understand the stabilizer concentrations in aqueous nano- and microsuspensions

Aqueous suspensions of poorly soluble, crystalline drug particles in the sub-micron range hold the ability to regulate the drug release for a defined period of time after e.g., intramuscular, or subcutaneous administration, working as an eminent formulation strategy for the preparation of long-acting injectables. Aqueous suspensions are typically prepared by top-down approaches, e.g., wet bead media milling or high-pressure homogenization, containing the active pharmaceutical compound and surfactants and/or polymers for stabilization purposes. Currently, the screening of proper stabilizers and adequate stabilizer concentration during formulation investigations is based on a trial-and-error approach with variations in combinations, concentrations, and/or ratios. To obtain a more efficient methodology during formulation screening, the present study investigated the correlation between the surface activity of two different surfactants, i.e., poloxamer 188 and polysorbate 20, by drop profile tensiometry and Langmuir trough monolayer, and the obtained sizes of cinnarizine particles as a tool to predict the optimal surfactant concentration to prepare physical stable nano- and microsuspensions. The obtained results demonstrated that the molecular area determined as the area per surfactant molecule measured in the Langmuir trough combined with the specific surface area of the prepared suspensions could be used to predict the suitable concentration of the surfactant based upon short-term stress stability data. The results further showed that higher concentrations of poloxamer 188 were necessary to stabilize the suspensions when compared to the needed concentration of polysorbate 20. In addition, it was observed that there was a need for a slightly higher surfactant concentration when the suspensions were milled with the smallest bead size of 0.5 mm instead of larger sizes of bead (0.8 and 1.0 mm), which could not be accounted for by differences in specific surface area.

Patient-Centric Long-Acting Injectable and Implantable Platforms─An Industrial Perspective

The increasing focus on patient centricity in the pharmaceutical industry over the past decade and the changing healthcare landscape, driven by factors such as increased access to information, social media, and evolving patient demands, has necessitated a shift toward greater connectivity and understanding of patients' unique treatment needs. One pharmaceutical technology that has supported these efforts is long acting injectables (LAIs), which lower the administration frequency for the patient's provided convenience, better compliance, and hence better therapeutical treatment for the patients. Furthermore, patients with conditions like the human immunodeficiency virus and schizophrenia have positively expressed the desire for less frequent dosing, such as that obtained through LAI formulations. In this work, a comprehensive analysis of marketed LAIs across therapeutic classes and technologies is conducted. The analysis demonstrated an increasing number of new LAIs being brought to the market, recently most as aqueous suspensions and one as a solution, but many other technology platforms were applied as well, in particular, polymeric microspheres and in situ forming gels. The analysis across the technologies provided an insight into to the physicochemical properties the compounds had per technology class as well as knowledge of the excipients typically used within the individual formulation technology. The principle behind the formulation technologies was discussed with respect to the release mechanism, manufacturing approaches, and the possibility of defining predictive in vitro release methods to obtain in vitro in vivo correlations with an industrial angle. The gaps in the field are still numerous, including better systematic formulation and manufacturing investigations to get a better understanding of potential innovations, but also development of new polymers could facilitate the development of additional compounds. The biggest and most important gaps, however, seem to be the development of predictive in vitro dissolution methods utilizing pharmacopoeia described equipment to enable their use for product development and later in the product cycle for quality-based purposes.

A Systematic Investigation of Process Parameters for Small-Volume Aqueous Suspension Production by the Use of Focused Ultrasonication

Aqueous suspensions containing crystalline drug in the sub-micron range is a favorable platform for long-acting injectables where particle size can be used to obtain a desired plasma-concentration profile. Stabilizers are added to the suspensions and screened extensively to define the optimal formulation composition. In the initial formulation screening the amount of drug compound can be limited, necessitating milling methods for small-volume screening predictable for scale-up. Hence, adaptive focused ultrasound was investigated as a potential milling method for rapid small-volume suspensions by identifying the critical process parameters during preparation. Suspensions containing drug compounds with different mechanical properties and thereby grindability, i.e., cinnarizine, haloperidol, and indomethacin with brittle, elastic, and plastic properties, respectively, were investigated to gain an understanding of the manufacturing with adaptive focused acoustics as well as comparison to already established milling techniques. Using a DoE-design, peak incident power was identified as the most crucial process parameter impacting the milling process for all three compounds. It was possible to decrease the sizes of drug particles to micron range after one minute of focused ultrasound exposure which was superior compared to other milling techniques (e.g., non-focused ultrasound exposure). The addition of milling beads decreased the drug particle sizes even further, thus to a lower degree than other already established milling techniques such as milling by dual centrifugation. This study thereby demonstrated that adaptive focused ultrasonication was a promising method for rapid homogenization and particle size reduction to micron range for different compounds varying in grindability without altering the crystalline structure.

Is roller milling - the low energy wet bead media milling - a reproducible and robust milling method for formulation investigation of aqueous suspensions?

Long-acting injectables have shown to offer a prolonged release of a drug compound up to several months, providing the opportunity to increase patient compliance for treatment of long-term and chronic conditions. Different formulation technologies have already been utilized for long-acting injectables, and especially aqueous suspensions with crystalline drug particles in the sub-micron range have sparked an interest for future development of long-acting injectables. Wet bead milling is a common top-down process used to prepare nano- and microsuspensions of crystalline drug particles with the addition of surfactants in the dispersion medium, which are working as stabilizers to prevent agglomeration or crystal growth that ultimately may influence the physical stability of nano- and microsuspensions. To examine the reproducibility of the suspensions manufactured and the behavior of their physical stability, i.e., changes in particle sizes over time, low-energy roller mill was utilized for the manufacturing of nano- and microsuspensions in the present study. Investigated formulation parameters was stabilizer type and concentration and milling parameters varied in bead size and duration of milling. The obtained results demonstrated that the physical stability of suspensions containing the two model compounds, cinnarizine and indomethacin, was highly affected by the constitution of surfactant and processing. Various size classes were obtained and accompanied by high variations between the individual samples that indicated uneven and unpredictable milling by the low-energy roller mill, limiting the possibility to prepare reproducible and physical stable suspensions. Short-term stability studies revealed clear tendencies towards reversed Ostwald ripening of suspensions stabilized with poloxamer 188 that contained cinnarizine as the drug compound, and to a smaller extent suspensions containing indomethacin. Furthermore, X-ray Powder Diffraction confirmed no alteration of the drug compounds crystal structure after roller milling for multiple days.

Wet bead milling by dual centrifugation - An approach to obtain reproducible and differentiable suspensions

Aqueous nano- and microsuspensions containing poorly water-soluble, crystalline drug particles have in the recent years sparked an interest for the preparation of long-acting injectables (LAIs), which increase patient compliance for patients treated for long-term or chronic conditions. Nano- and microsuspensions are often prepared by top-down methods, such as wet bead milling, with the addition of stabilizers in the dispersion media, such as surfactants, which influence the particle sizes and physical stability of the suspension. To improve the efficacy of formulation screening for nano- and microsuspensions, dual centrifugation was utilized in this study whereby 40 samples could be manufactured simultaneously to support the formulation definition. Hence, the type and concentration of stabilizer as well as bead size and milling speed was investigated throughout the presented study, but also the ability of the method to produce consistent data was investigated. The obtained results demonstrated that the particle profile obtained after milling was very consistent from run to run and so was the observed stability data, i.e., running n = 1 experiment per combination could clearly be justified as a predictable approach for the formulation screening. The data also showed that the stabilizer, as well as its concentration highly influenced the physical stability of suspensions containing both the two investigated model compounds, i.e., both cinnarizine and indomethacin, where the biggest increase in particle sizes was observed within the first week. For short-term studies, polysorbate 20 was found to be a suitable stabilizer for suspensions of cinnarizine, whereas sodium dodecyl sulphate was more suitable for indomethacin suspensions immediately after the milling even with 1% (w/v) stabilizer solution, but not sufficient for short-term stability due to an insufficient stabilizer concentration. Smaller particles sizes could be achieved by milling the suspensions with the smallest bead sizes and at the highest speed of 1500 rpm without disrupting the crystal structure of the active pharmaceutical ingredient (API), which was confirmed by X-ray Powder Diffraction.