Assessing Drug Release from Manipulated Abuse Deterrent Formulations

The effect of food vehicles on in vitro performance of pantoprazole sodium delayed release sprinkle formulation

Certain patient populations, including children, the elderly or people with dysphagia, find swallowing whole medications such as tablets and capsules difficult. To facilitate oral administration of drugs in such patients, a common practice is to sprinkle the drug products (e.g., usually after crushing the tablet or opening the capsule) on food vehicles before consumption which improves swallowability. Thus, evaluation of the impact of food vehicles on the potency and stability of the administered drug product is important. The aim of the current study was to evaluate the physicochemical properties (viscosity, pH, and water content) of common food vehicles used for sprinkle administration (e.g., apple juice, applesauce, pudding, yogurt, and milk) and their impacts on the in vitro performance (i.e., dissolution) of pantoprazole sodium delayed release (DR) drug products. The food vehicles evaluated exhibited marked difference in viscosity, pH and water content. Notably, the pH of the food as well as the interaction between food vehicle pH and drug-food contact time were the most significant factors affecting the in vitro performance of pantoprazole sodium DR granules. For example, the dissolution of pantoprazole sodium DR granules sprinkled on food vehicles of low pH (e.g., apple juice or applesauce) for short durations remained unchanged compared with the control group (i.e., without mixing with food vehicles). However, use of high pH food vehicles (e.g., milk) with prolonged contact time (e.g., 2 h) resulted in accelerated pantoprazole release, drug degradation and loss of potency. Overall, a thorough assessment of physicochemical properties of food vehicles and formulation characteristics are a necessary part of the development of sprinkle formulations.

Emerging trends in Abuse-Deterrent Formulations: Technological insights and Regulatory considerations

BACKGROUND

Opioid medications are an integral part in the management of acute and chronic severe pain. However, non-medical practice of these prescription drug products is emerging as a serious public health problem. To control this opioid epidemic, USFDA is encouraging pharmaceutical companies to develop Abuse Deterrent Formulations (ADFs). Abuse Deterrent Formulations are much more difficult to manipulate and abuse when compared to their conventional formulations. This feature of ADFs is due to their ability to incumber extraction of active ingredients, to prevent administration through alternative routes and making abuse of altered product less rewarding.

OBJECTIVE

The main objective of this review is to abridge different ADFs and various laboratory-based in vitro manipulation and extraction studies, demonstrating that these approved ADFs have capabilities to deter abuse.

METHODS

The method includes collection of data from different search engines like PubMed, FDA guidance documents, ScienceDirect, Google Patents to get coverage of literature in order to get appropriate information regarding ADFs.

RESULTS

Various in vitro studies demonstrate that ADFs are effective in minimizing opioid drug abuse including opioid overdose. However, real impact of these ADFs on reducing the drug abuse can be concluded only after receiving the post marketing data.

CONCLUSION

ADFs are embracing fundamentally different paradigm in management of severe pain. We believe that development of abuse deterrent technologies would shift the architype, deterring multipill abuse and can prove as a breakthrough strategy in controlling this opioid epidemic menace.

Preferential Oxycodone Loss of Physically Manipulated Abuse Deterrent Oxycodone HCl Extended Release Tablets Prepared for Nasal Insufflation Studies

A method to reproducibly mill abuse deterrent oxycodone hydrochloride (HCl) extended release (ER) tablets was developed for a nasal insufflation pharmacokinetic (PK) study. Several comminution methods were explored before determining that a conical mill resulted in controlled milling of tablets to a size range equal to or below 1000 μm. However, milling resulted in significant loss of oxycodone from abuse deterrent oxycodone HCl ER tablets compared to minimal oxycodone loss from oxycodone HCl immediate release (IR) tablets. Characterization of milled tablet powder showed that loss of oxycodone was not attributed to analytical procedures or oxycodone phase change during high intensity milling processes. The content uniformity of oxycodone in the milled tablet powder varied when ER and IR tablets were milled to a particle size distribution equal to or below 500 μm but did not vary when particles were sized above 500 µm to equal to or below 1000 μm. In addition, the initial excipient weight to drug substance weight ratio impacted the amount of oxycodone lost from the respective formulation. However, dissolution demonstrated that when oxycodone HCl ER tablets are milled, differences in excipient weight to drug substance weight ratio and particle size distribution of milled tablets did not result in significantly different release of oxycodone.

Investigating the Influence of Tablet Location Inside Dissolution Test Apparatus on Polymer Erosion and Drug Release of a Surface-Erodible Sustained-Release Tablet Using Computational Simulation Methods

The objective of this work was to investigate the influence of tablet location along the bottom of a USP apparatus II vessel on polymer erosion and drug release of surface-erodible sustained-release tablets using computational simulation methods. Computational fluid dynamics (CFD) methods were performed to simulate the velocity distribution. A mathematical model was developed to describe polymer erosion and tablet deformation according to the mass transfer coefficient. Numerical analysis was used to simulate drug release controlled by drug diffusion and polymer erosion. The results indicated that tablets located at the off-center position deformed faster than the tablets located at the center position. However, tablet location had no profound impact on drug release rate since all drug release profiles were "similar" according to the f₂ similarity values which were above 50. Hence, our simulation supported that the USP apparatus II was a reliable and robust device for the dissolution testing of surface-erodible sustained-release tablets.

Use of Drug Release Testing to Evaluate the Retention of Abuse-Deterrent Properties of Polyethylene Oxide Matrix Tablets

Abuse-deterrent formulations (ADFs) using physical/chemical barrier approaches limit abuse by providing resistance to dosage form manipulation to limit drug extraction or altered release. Standardizing in vitro testing methods to assess the resistance to manipulation presents a number of challenges, including the variation in particle sizes resulting from the use of various tools to alter the tablet matrix (e.g., grinding, chipping, crushing). A prototype, direct-compression ADF using a sintered polyethylene oxide (PEO) matrix containing dextromethorphan, an enantiomeric form of the opioid, levorphanol, was developed to evaluate testing methodologies for retention of abuse-deterrent properties following dosage form tampering. Sintered PEO tablets were manipulated by grinding, and drug content and release were evaluated for the recovered granules. Drug content analysis revealed that higher amounts of drug were contained in the smaller size granules (< 250 μm, 190% of the theoretical amount) compared with the larger particles (> 250 μm, 55-75% of theoretical amount). Release testing was performed on various size granule fractions (> 850 μm, 500-850 μm, 250-500 μm, and < 250 μm) using USP type I (basket), type II (paddle), and type IV (flow-through) apparatus. The USP type I and type II apparatus gave highly variable release results with poor discrimination among the release rates from different size granules. The observed sticking of the hydrated granules to the baskets and paddles, agglomeration of hydrated granules within the baskets/vessels, and ongoing PEO hydration with subsequent gel formation further altered the particle size and impacted the rate of drug release. The use of a flow-through apparatus (USP type IV) resulted in improved discrimination of drug release from different size granules with less variability due to better dispersion of granules (minimal sticking and aggregation). Drug release profiles from the USP type IV apparatus showed that the larger size granules (> 500 μm) offered continued resistance to drug release following tablet manipulation, but the smaller size granules (< 500 μm) provided rapid drug release that was unhindered by the hydrated granule matrix. Since < 500-μm size particles are preferred for nasal abuse, improved direct-compression ADF formulations should minimize the formation of these smaller-sized particles following tampering to maintain the product's abuse-deterrent features.