Trackerless ultrasound-integrated bone cement detection using a modular minirobot in revision total hip replacement

A Newly Designed "SkyWalker" Robot Applied in Total Knee Arthroplasty: A Retrospective Cohort Study for Femoral Rotational Alignment Restoration

Objective

This study explored whether robotic arm‐assisted total knee arthroplasty (RATKA) has the advantage of restoring femoral rotational alignment compared to conventional total knee arthroplasty (COTKA).

Methods

Sixty patients (45 women and 15 men) attending our department from May 2019 to December 2020 were selected and divided into two groups, with 30 patients in each group, according to whether they underwent COTKA or RATKA. Femoral rotational alignment results, such as, posterior condylar angle (PCA), patella transverse axis‐femoral transepicondylar axis angle (PFA), radiological findings, such as, hip‐knee‐ankle angle (HKA), lateral distal femoral angle (LDFA), and medial proximal tibial angle (MPTA), and operative data (operation time, intraoperative blood loss, tourniquet time, and length of stay (LOS), and clinical outcomes, such as maximum knee flexion angle (MKFA), Knee Society Score (KSS), and Western Ontario Mac Master University Index Score (WOMAC) were compared within and between the two groups.

Results

PCA and PFA in the RATKA group were (0.6 ± 0.3)° and (0.9 ± 0.3)°, respectively, which were smaller than (1.5 ± 2.0)° and (3.1 ± 1.1)° in the COTKA group (P < 0.05), and were closer to 0°; the differences in HKA, LDFA, and MPTA were not statistically significant. With the exception of the LDFA, the HKA, MPTA, PCA, and PFA improved in both groups after surgery (P < 0.05). The blood loss and the LOS of RATKA group were 192.3 ± 23.1 mL and 8.2 ± 1.4 days, which were less than 203.7 ± 29.8 mL and 9.3 ± 1.1 days of the COTKA group, but the operation time showed no statistically significant difference, and the tourniquet time was longer (P < 0.05). The MKFA in the RATKA group was (123.0 ± 3.7)°, which was greater than (116.3 ± 4.6)° in the COTKA group (P < 0.05). In terms of scores, the postoperative results were better than the preoperative results in both groups (P < 0.05). However, there was no statistically significant difference between the groups.

Conclusion

The accuracy of femoral rotational alignment reconstructed achieved by RATKA is significantly better than that of COTKA and is more conducive to the recovery of knee flexion function after surgery; although RATKA reduces intraoperative blood loss and postoperative LOS, the short‐term clinical efficacy comparison has not yet demonstrated the advantages of robotic technology, and a more optimized design is needed to improve the efficiency of RATKA surgery.

MINARO HD: control and evaluation of a handheld, highly dynamic surgical robot

Purpose

Current surgical robotic systems are either large serial arms, resulting in higher risks due to their high inertia and no inherent limitations of the working space, or they are bone-mounted, adding substantial additional task steps to the surgical workflow. The robot presented in this paper has a handy and lightweight design and can be easily held by the surgeon. No rigid fixation to the bone or a cart is necessary. A high-speed tracking camera together with a fast control system ensures the accurate positioning of a burring tool.

Methods

The capabilities of the robotic system to dynamically compensate for unintended motion, either of the robot itself or the patient, was evaluated. Therefore, the step response was analyzed as well as the capability to follow a moving target.

Results

The step response show that the robot can compensate for undesired motions up to 12 Hz in any direction. While following a moving target, a maximum positioning error of 0.5 mm can be obtained with a target motion of up to 18 mm/s.

Conclusion

The requirements regarding dynamic motion compensation, accuracy, and machining speed of unicompartmental knee arthroplasties, for which the robot was optimized, are achieved with the presented robotic system. In particular, the step response results show that the robot is able to compensate for human tremor.

OR.NET RT: how service-oriented medical device architecture meets real-time communication

Today’s landscape of medical devices is dominated by stand-alone systems and proprietary interfaces lacking cross-vendor interoperability. This complicates or even impedes the innovation of novel, intelligent assistance systems relying on the collaboration of medical devices. Emerging approaches use the service-oriented architecture (SOA) paradigm based on Internet protocol (IP) to enable communication between medical devices. While this works well for scenarios with no or only soft timing constraints, the underlying best-effort communication scheme is insufficient for time critical data. Real-time (RT) networks are able to reliably guarantee fixed latency boundaries, for example, by using time division multiple access (TDMA) communication patterns. However, deterministic RT networks come with their own limitations such as tedious, inflexible configuration and a more restricted bandwidth allocation. In this contribution we overcome the drawbacks of both approaches by describing and implementing mechanisms that allow the two networks to interact. We introduce the first implementation of a medical device network that offers hard RT guarantees for control and sensor data and integrates into SOA networks. Based on two application examples we show how the flexibility of SOA networks and the reliability of RT networks can be combined to achieve an open network infrastructure for medical devices in the operating room (OR).

Electrical Bioimpedance-Controlled Surgical Instrumentation

A bioimpedance-controlled concept for bone cement milling during revision total hip replacement is presented. Normally, the surgeon manually removes bone cement using a hammer and chisel. However, this procedure is relatively rough and unintended harm may occur to tissue at any time. The proposed bioimpedance-controlled surgical instrumentation improves this process because, for example, most risks associated with bone cement removal are avoided. The electrical bioimpedance measurements enable online process-control by using the milling head as both a cutting tool and measurement electrode at the same time. Furthermore, a novel integrated surgical milling tool is introduced, which allows acquisition of electrical bioimpedance data for online control; these data are used as a process variable. Process identification is based on finite element method simulation and on experimental studies with a rapid control prototyping system. The control loop design includes the identified process model, the characterization of noise as being normally distributed and the filtering, which is necessary for sufficient accuracy ( ±0.5 mm). Also, in a comparative study, noise suppression is investigated in silico with a moving average filter and a Kalman filter. Finally, performance analysis shows that the bioimpedance-controlled surgical instrumentation may also performs effectively at a higher feed rate (e.g., 5 mm/s).