Performance of the resurfaced hip. Part 1: The influence of the prosthesis size and positioning on the remodelling and fracture of the femoral neck

Morphometric evaluation of proximal femur in patients with unilateral total hip prosthesis

It is important to know the morphometric characteristics of the proximal femur. This is necessary to reduce the risk of complications related to surgical procedures performed in the area due to vascular, metabolic, or traumatic causes. It is of importance for achieving the alignment of the prosthesis to be implanted as well. The aim of this study was to evaluate the morphometric characteristics of the proximal femur and to establish a database for making and performing total hip prosthesis. Anteroposterior (AP) pelvic radiographs of 162 cases, with a mean age of 65.6 years, who had undergone unilateral total hip arthroplasty were used in this study. Femoral head diameter (FHD), femoral neck width (FNW), femoral neck length (FNL), femoral neck axis length (FNAL), intertrochanteric line length (ILL), and neck-shaft angle (NSA) were measured on radiographs obtained digitally using setrapacs media. FHD was found to be 48.1 ± 3.7 mm, FNW 35.4 ± 4.2 mm, FNL 30.8 ± 6.1 mm, FNAL 98.6 ± 9.4 mm, ILL 81.1 ± 7.9 mm, and NSA 130.4 ± 5.1° on average. The comparison of the mean values for females and males revealed a statistically significant difference between the FHD, FNW, FNL, FNAL, and ILL (P = 0.000). There was no statistically significant difference in NSA between males and females (P = 0.356). A weak correlation was found between age and parameter values using correlation analysis (r < 0.24, P > 0.05). In morphometric assessment of the proximal femur, taking into consideration regional and sexual differences is of importance for prosthesis design and surgical success.

Predictors of femoral neck fracture following hip resurfacing: a cadaveric study

We aimed to establish if radiological parameters, dual energy x-ray absorptiometry (DEXA) and quantitative CT (qCT) could predict the risk of sustaining a femoral neck fracture following hip resurfacing. Twenty-one unilateral fresh frozen femurs were used. Each femur had a plain digital anteroposterior radiograph, DEXA scan and qCT scan. Femurs were then prepared for a Birmingham Hip Resurfacing femoral component and loaded to failure. Results demonstrated that gender and qCT measurements showed strong correlation with failure load. QCT could be used as an individual measure to predict risk of post-operative femoral neck fracture. However, when qCT is unavailable; gender, pre-operative DEXA scan and Neck Width measurements can be used together to assess risk of post-operative femoral neck fracture in patients due to undergo hip resurfacing.

Experimental evaluation of new concepts in hip arthroplasty

In this thesis we evaluated two different hip arthroplasty concepts trough in vitro studies and numerical analyses. The cortical strains in the femoral neck area were increased by 10 to 15 % after insertion of a resurfacing femoral component compared to values of the intact femur, shown in an in vitro study on human cadaver femurs. There is an increased risk of femoral neck fracture after hip resurfacing arthroplasty. An increase of 10 to 15 % in femoral neck strains is limited, and cannot alone explain these fractures. Together with patient specific and surgical factors, however, increased strain can contribute to increased risk of fracture. An in vitro study showed that increasing the neck length in combination with retroversion or reduced neck shaft angle on a standard cementless femoral stem does not compromise the stability of the stem. The strain pattern in the proximal femur increased significantly at several measuring sites when the version and length of neck were altered. However, the changes were probably too small to have clinical relevance. In a validation study we have shown that a subject specific finite element analysis is able to perform reasonable predictions of strains and stress shielding after insertion of a femoral stem in human cadaver femurs. The usage of finite element models can be a valuable supplement to in vitro tests of femoral strain pattern around hip arthroplasty. Finally, a patient case shows that bone resorption around an implant caused by stress shielding can in extreme cases lead to periprosthetic fracture.

Pre-clinical evaluation of ceramic femoral head resurfacing prostheses using computational models and mechanical testing

Ceramic-on-ceramic hip resurfacing can potentially offer the bone-conserving advantages of resurfacing while eliminating metal ion release. Thin-walled ceramic resurfacing heads are conceivable following developments in the strength and reliability of ceramic materials, but verification of new designs is required. The present study aimed to develop a mechanical pre-clinical analysis verification process for ceramic resurfacing heads, using the DeltaSurf prosthesis design as a case study.

Finite element analysis of a range of in vivo scenarios was used to design a series of physiologically representative mechanical tests, which were conducted to verify the strength of the prosthesis. Tests were designed to simulate ideal and worst-case in vivo loading and support, or to allow comparison with a clinically successful metallic device.

In tests simulating ideal loading and support, the prosthesis sustained a minimum load of 39 kN before fracture, and survived 10 000 000 fatigue cycles of 0.534 kN to 5.34 kN. In worst-case tests representing a complete lack of superior femoral head bone support or pure cantilever loading of the prosthesis stem, the design demonstrated strength comparable to that of the equivalent metal device.

The developed mechanical verification test programme represents an improvement in the state of the art where international test standards refer largely to total hip replacement prostheses. The case study’s novel prosthesis design performed with considerable safety margins compared with extreme in vivo loads, providing evidence that the proposed ceramic resurfacing heads should have sufficient strength to perform safely in vivo. Similar verification tests should be designed and conducted for novel ceramic prosthesis designs in the future, leading the way to clinical evaluation.

Experimental validation of a finite element model of the proximal femur using digital image correlation and a composite bone model

Computational biomechanical models are useful tools for supporting orthopedic implant design and surgical decision making, but because they are a simplification of the clinical scenario they must be carefully validated to ensure that they are still representative. The goal of this study was to assess the validity of the generation process of a structural finite element model of the proximal femur employing the digital image correlation (DIC) strain measurement technique. A finite element analysis model of the proximal femur subjected to gait loading was generated from a CT scan of an analog composite femur, and its predicted mechanical behavior was compared with an experimental model. Whereas previous studies have employed strain gauging to obtain discreet point data for validation, in this study DIC was used for full field quantified comparison of the predicted and experimentally measured strains. The strain predicted by the computational model was in good agreement with experimental measurements, with R(2) correlation values from 0.83 to 0.92 between the simulation and the tests. The sensitivity and repeatability of the strain measurements were comparable to or better than values reported in the literature for other DIC tests on tissue specimens. The experimental-model correlation was in the same range as values obtained from strain gauging, but the DIC technique produced more detailed, full field data and is potentially easier to use. As such, the findings supported the validity of the model generation process, giving greater confidence in the model's predictions, and digital image correlation was demonstrated as a useful tool for the validation of biomechanical models.