Phenobarbital molecularly imprinted polymer selectively binds phenobarbital

Preparation of a New Solid-Phase Microextraction Fiber Based on Molecularly Imprinted Polymers for Monitoring of Phenobarbital in Urine Samples

A simple solid-phase microextraction technique using molecularly imprinted polymers (MIP-SPME) was prepared to monitor phenobarbital in urine samples. In this technique, the fiber was prepared via insertion of the modified stainless-steel wire in the reaction solution including 3-aminopropyltriethoxysilane and tetraethyl orthosilicate in the presence of an acidic catalyst (acetic acid). The fabricated MIP-SPME fiber was utilized to selectively extract phenobarbital from urine samples and prepare it for detection through high-performance liquid chromatography with ultraviolet detection. The synthesized MIPs were characterized by several techniques such as Fourier-transform infrared spectroscopy, field emission scanning electron microscopy, and thermal gravimetric analysis. The effects of various influencing factors on the extraction yield of phenobarbital were considered and optimized. The conditions that yielded the maximum extraction efficiency were as follows: pH of 5, 25 min extraction time, 500 rpm stirring rate, 15 min desorption time and using methanol as elution solvent. Within the range of concentrations of 0.02 to 100 μg mL-1, the method had linear characteristics, with a suitable coefficient of determination (0.9983). We determined limits of detection and limits of quantification to be 9.88 and 32.9 ng mL-1, respectively. The repeatability and reproducibility of the prepared fibers were 4.6 and 6.5%, respectively.

Preparation of Molecular Imprinted Polymer Based on Chitosan as the Selective Sorbent for Solid-Phase Microextraction of Phenobarbital

This study reports the construction of a novel SPME fiber based on chitosan and glutaraldehyde as coating material composites combined with high-performance liquid chromatography with an ultraviolet detector (HPLC-UV) for extraction and detection of phenobarbital. In this technique, the chitosan biopolymer, as a new coating of SPME fiber, was produced on the stainless-steel wire, using glutaraldehyde and phenobarbital as cross-linker and template, respectively. For comparison, a nonimprinted polymer was created using the same procedure to evaluate fiber selectivity (but without the addition of phenobarbital). The SPME-MIP fiber coating was characterized by field emission scanning electron microscopy, Fourier-transform infrared spectroscopy, and thermal gravimetric analysis. The efficiency of fiber was then improved by adjusting the impact of numerous factors such as pH, extraction time, desorption time, desorption solvent, and stirring rate. The results showed that the proposed fiber has a linear range of 0.01-4 μg·mL^-1, and detection limit of 7.5 ng·mL^-1. The average recoveries in the four concentration levels for the spiked river and well water samples were 95.7 and 95.3%, with relative standard deviations of 3.8 and 5.9% for single fiber and between fibers, respectively.

Molecular imprinting science and technology: a survey of the literature for the years up to and including 2003

Over 1450 references to original papers, reviews and monographs have herein been collected to document the development of molecular imprinting science and technology from the serendipitous discovery of Polyakov in 1931 to recent attempts to implement and understand the principles underlying the technique and its use in a range of application areas. In the presentation of the assembled references, a section presenting reviews and monographs covering the area is followed by papers dealing with fundamental aspects of molecular imprinting and the development of novel polymer formats. Thereafter, literature describing attempts to apply these polymeric materials to a range of application areas is presented.

Molecularly imprinted adsorbents for positional isomer separation

2,4-Dihydroxybenzophenone (2,4-DHB) imprinted polymers were synthesized by surface imprinting technique, using allyl alcohol as the functional monomer. The polymers showed a very high selectivity for 2,4-DHB when compared with various positional isomers such as 2-HB, 2,2'-DHB, 4,4'-DHIB and 4,4'-DMB. Solvents were found to affect the selectivity as well as sorption capacity in the case of surface imprinted polymers. The selectivities decreased drastically when the imprint cavity was blocked. This validated the importance of the cavity and the rebinding interactions in governing the selectivity in the case of MIPs. The surface imprinted polymers also showed a high selectivity under non-equilibrium conditions thereby making them suitable adsorbents for industrial separations.