Evaluation of Weight Variation in Mini-Tablets Manufactured by a Multiple-Tip Tool

Development of a New Jelly Coating Technology (Oral Jelly Coating) to Improve Prescribed Medication Adherence

Tablets are the most commonly prescribed dosage form for oral drug administration. Historically, improvement of medication adherence of tablets has been facilitated through, for example, the use of smaller tablets, distinctive shaped tablets and sugar-coated tablets. In addition, new formulation technologies such as orally disintegrating tablets (OD tablets), micro tablet-type granules, jellies, and film formulations are making it possible to create more easily ingested dosage forms. We have developed a new oral jelly coating formulation that can be applied to any sized tablet without reducing the size of the formulation. It was found that this new jelly layer formed on the tablet surface improved the tablet's slipperiness with an appropriate amount of water, while ensuring no change in the dissolution profile. In addition, the jelly layer was ensured storage stability over time without affecting the dissolution profile. Although further studies are needed, this coating technology can quickly change the tablet surface to a jelly-like state after the tablet is taken, giving the tablet the same slipperiness as if it were taken in jelly, making it easier to pass through the pharynx, and thus improving medication adherence.

Novel Bioequivalent Tablet of Solifenacin Succinate Prepared Using Direct Compression Technique for Improved Chemical Stability

We designed a bioequivalent tablet form of solifenacin succinate (SOL) with an improved storage stability using a direct compression (DC) technique. An optimal direct compressed tablet (DCT) containing an active substance (10 mg), lactose monohydrate, and silicified microcrystalline cellulose as diluents, crospovidone as a disintegrant, and hydrophilic fumed silica as an anti-coning agent was constructed by evaluating the drug content uniformity, mechanical properties, and in vitro dissolution. The physicochemical and mechanical properties of the DCT were as follows: drug content 100.1 ± 0.7%, disintegration time of 6.7 min, over 95% release within 30 min in dissolution media (pH 1.2, 4.0, 6.8, and distilled water), hardness > 107.8 N, and friability ~0.11%. The SOL-loaded tablet fabricated via DC showed an improved stability at 40 °C and RH 75%, exhibiting markedly reduced degradation products compared to those fabricated using ethanol or water-based wet granulation or a marketed product (Vesicare^®, Astellas Pharma). Moreover, in a bioequivalence study in healthy subjects (n = 24), the optimized DCT offered a pharmacokinetic profile comparable to that of the marketed product, with no statistical differences in the pharmacokinetic parameters. The 90% CIs for the geometric mean ratios of the test to the reference formulation for the area under the curve and the maximum drug concentration in plasma were 0.98-1.05 and 0.98-1.07, respectively, and satisfied the FDA regulatory criteria for bioequivalence. Thus, we conclude that DCT is a beneficial oral dosage form of SOL with an improved chemical stability.

Charge Reduction Assisted Production of Diminutive Fluid Bed Granules for High Drug Load Minitablets

Micronized drug powders are generally unsuitable as tableting feed to produce minitablets due to their cohesivity and poor flow. The silicification of fine paracetamol powder (PCM_F) with an optimal concentration range of fumed silica (fSi) [0.7 - 0.9 %, w/w] reduced the net negative charge of PCM_F and improved powder flow. The optimal fSi concentration range suitable was established through the measurement of charge and flowability of the silicified powders. Silicification of PCM_F by physical mix did not satisfactorily overcome the cohesive forces between the PCM_F crystals and improve powder flow sufficiently such that it will feed consistently into the smaller die orifices during tableting. Using a specialized fluid bed system with swirling air and side spray, controlled granulation of silicified PCM_F packed and agglomerated the interlocking-prone needle shaped PCM_F crystals into diminutive granules that are more spherical and free flowing. With optimized fSi concentration (≈ 0.8 %, w/w) and granulation process parameters, high drug load diminutive granules (D₅₀≃ 90 μm) were successfully prepared from PCM_F as starter seeds (D₅₀≃ 30 μm). Minitablets prepared from the diminutive granules had low weight variation, and were mechanically strong with disintegration time of less than 30 s. This study demonstrated the feasibility of producing high drug load minitablets from a cohesive, electrostatic-prone fine drug powder.

Implementing the Design of Experiments (DoE) Concept into the Development Phase of Orodispersible Minitablets (ODMTs) Containing Melatonin

Development of orodispersible minitablets (ODMTs) requires consideration of aspects related to small dimensions, while ensuring short disintegration time with sufficient mechanical stability. In order to meet these and other critical quality attributes (CQAs), quality by design is encouraged. According to this approach, formulation and compression process factors were systematically studied using design of experiments (Plackett-Burman for screening purposes, full and fractional factorial design for in-depth characterization) to understand their influence on CQAs of orodispersible minitablets containing melatonin. Mathematical models describing the relationships between processing variables and attributes such as resistance to crushing and disintegration time were successfully developed, characterized by high coefficients of determination (R²_adj = 0.90-0.97) and prediction errors in the range (+2.4 to -10.8%). In conclusion, based on these models, the design space was created for melatonin ODMTs, ensuring the product's quality and process robustness. Moreover, the study demonstrated the suitability of texture analysis as an alternative to compendial measurement methods of resistance to crushing and disintegration time. Graphical abstract.

Effects of Manufacturing Process Variables on the Tablet Weight Variation of Mini-tablets Clarified by a Definitive Screening Design

This study investigated the effect of manufacturing process variables of mini-tablets, in particular, the effect of process variables concerning fluidized bed granulation on tablet weight variation. Test granules were produced with different granulation conditions according to a definitive screening design (DSD). The five evaluated factors assigned to DSD were: the grinding speed of the sample mill at the grinding process of the active pharmaceutical ingredient (X1), microcrystalline cellulose content in granules (X2), inlet air temperature (X3), binder concentration (X4) and the spray speed of the binder solution (X5) at the granulation process. First, the relationships between the evaluated factors and the granule properties were investigated. As a result of the DSD analysis, the mode of action of granulation parameters on the granule properties was fully characterized. Subsequently, the variation in tablet weight was examined. In addition to mini-tablets (3 mm diameter), this experiment assessed regular tablets (8 mm diameter). From the results for regular tablets, the variation in tablet weight was affected by the flowability of granules. By contrast, regarding the mini-tablets, no significant effect on the variation of tablet weight was found from the evaluated factors. From this result, this study further focused on other important factors besides the granulation process, and then the effect of the die-hole position of the multiple-tip tooling on tablet weight variation was proven to be significant. Our findings provide a better understanding of manufacturing mini-tablets.