Video Analysis of the Deformation and Effective Mass of Gymnastics Landing Mats

Reliability of Impact Forces, Hip Angles and Velocities during Simulated Forward Falls Using a Novel Propelled Upper Limb Fall ARrest Impact System (PULARIS)

Previous forward fall simulation methods have provided good kinematic and kinetic data, but are limited in that they have started the falls from a stationary position and have primarily simulated uni-directional motion. Therefore, a novel Propelled Upper Limb fall ARest Impact System (PULARIS) was designed to address these issues during assessments of a variety of fall scenarios. The purpose of this study was to present PULARIS and evaluate its ability to impact the upper extremities of participants with repeatable velocities, hand forces and hip angles in postures and with vertical and horizontal motion consistent with forward fall arrest. PULARIS consists of four steel tubing crossbars in a scissor-like arrangement that ride on metal trolleys within c-channel tracks in the ceiling. Participants are suspended beneath PULARIS by the legs and torso in a prone position and propelled horizontally via a motor and chain drive until they are quick released, and then impact floor-mounted force platforms with both hands. PULARIS velocity, hip angles and velocities and impact hand forces of ten participants (five male, five female) were collected during three fall types (straight-arm, self-selected and bent-arm) and two fall heights (0.05 m and 0.10 m) to assess the reliability of the impact conditions provided by the system. PULARIS and participant hip velocities were found to be quite repeatable (mean ICC = 0.81) with small between trial errors (mean = 0.03 m/s). The ratio of horizontal to vertical hip velocity components (∼0.75) agreed well with previously reported data (0.70-0.80). Peak vertical hand impact forces were also found to be relatively consistent between trials with a mean ICC of 0.73 and mean between trial error of 13.4 N. Up to 83% of the horizontal hand impact forces displayed good to excellent reliability (ICC > 0.6) with small between trial differences. Finally, the ICCs for between trial hip angles were all classified as good to excellent. Overall, PULARIS is a reliable method and is appropriate for studying the response of the distal upper extremity to impact loading during non-stationary, multi-directional movements indicative of a forward fall. This system performed well at different fall heights, and allows for a variety of upper and lower extremity, and hip postures to be tested successfully in different landing scenarios consistent with elderly and sport-related falls.

Modifying landing mat material properties may decrease peak contact forces but increase forefoot forces in gymnastics landings

This study investigated how changes in the material properties of a landing mat could minimise ground reaction forces (GRF) and internal loading on a gymnast during landing. A multi-layer model of a gymnastics competition landing mat and a subject-specific seven-link wobbling mass model of a gymnast were developed to address this aim. Landing mat properties (stiffness and damping) were optimised using a Simplex algorithm to minimise GRF and internal loading. The optimisation of the landing mat parameters was characterised by minimal changes to the mat's stiffness (<0.5%) but increased damping (272%) compared to the competition landing mat. Changes to the landing mat resulted in reduced peak vertical and horizontal GRF and reduced bone bending moments in the shank and thigh compared to a matching simulation. Peak bone bending moments within the thigh and shank were reduced by 6% from 321.5 Nm to 302.5Nm and GRF by 12% from 8626 N to 7552 N when compared to a matching simulation. The reduction in these forces may help to reduce the risk of bone fracture injury associated with a single landing and reduce the risk of a chronic injury such as a stress fracture.

Reducing ground reaction forces in gymnastics' landings may increase internal loading

The aim of this study was to use a subject-specific seven-link wobbling mass model of a gymnast, and a multi-layer model of a landing mat, to determine landing strategies that minimise ground reaction forces (GRF) and internal forces. Subject-specific strength parameters were determined that defined the maximum voluntary torque/angle/angular velocity relationship at each joint. These relationships were used to produce subject-specific 'lumped' linear muscle models for each joint. Muscle activation histories were optimised using a Simplex algorithm to minimise GRF or bone bending moments for forward and backward rotating vault landings. Optimising the landing strategy to minimise each of the GRF reduced the peak vertical and horizontal GRF by 9% for the backward rotating vault and by 8% and 48% for the forward rotating vault, compared to a matching simulation. However, most internal loading measures (bone bending moments, joint reaction forces and muscle forces) increased compared to the matching simulation. Optimising the landing strategy to minimise the peak bone bending moments resulted in reduced internal loading measures, and in most cases reduced GRF. Bone bending moments were reduced by 27% during the forward rotating vault and by 2% during the backward rotating vault landings when compared to the matching simulations. It is possible for a gymnast to modify their landing strategy in order to minimise internal forces and lower GRF. However, using a reduction in GRF, due to a change in landing strategy, as a basis for a reduction in injury potential in vaulting movements may not be appropriate since internal loading can increase.

Lesões desportivas na ginástica artística: estudo a partir de morbidade referida

INTRODUÇÃO: Os níveis de exigência biomecânica devidos ao alto grau de dificuldade na realização de gestos fazem da ginástica artística (GA) uma modalidade com elevado risco de lesões. Assim, é necessário que os aspectos a elas relacionados sejam controlados. OBJETIVO: Analisar a ocorrência de lesões na Ginástica Artística, associando-as a fatores de risco específicos da modalidade e do atleta, a partir de inquérito de morbidade referida. MÉTODOS: Foram entrevistados 54 ginastas, recrutados ao acaso, classificados segundo o nível competitivo em duas categorias: regional e nacional. Utilizou-se o inquérito de morbidade referida (IMR) com a finalidade de reunir dados sobre a natureza da lesão, região corporal e aparelho ginástico. Os dados foram organizados e apresentados sob a forma de distribuição de freqüências e as variáveis, analisadas segundo nível de associação a partir do teste de Goodman para contrastes entre populações multinomiais, considerando significante o valor P < 0,05. RESULTADOS: Presença de lesão durante a temporada foi relatada por 39 (71,70%) atletas, sendo 22 (56,41%) mulheres e 17 (43,59%) homens. Nas categorias regional masculino e feminino e nacional feminino, a maior ocorrência de lesões foi de origem articular, correspondendo a 55,56%, 50% e 45,45% do total, respectivamente. Para o sexo feminino nacional, os membros inferiores foram os mais referidos (68,18%) e, em ambas as categorias, as lesões ocorreram nos aparelhos de saltos (79,41%), enquanto que no sexo masculino nacional o maior número de agravos foi verificado nos aparelhos de apoio e suspensão (72%). CONCLUSÕES: Há elevada freqüência de lesões, acometendo principalmente articulações e membros inferiores, sendo os aparelhos de saltos os mais referidos quanto à ocorrência de acometimentos. Foi observado também que, quanto maiores as exigências de desempenho técnico, maior a freqüência de lesões.

Modeling a Viscoelastic Gymnastics Landing Mat during Impact

Landing mats that can undergo a large amount of area deformation are now essential for the safe completion of landings in gymnastics. The objective of this study was to develop an analytical model of a landing mat that reproduces the key characteristics of the mat-ground force during impact with minimal simulation run time. A force plate and two high-speed video cameras were used to record the mat deformation during vertical drop testing of a 24-kg impactor. Four increasingly complex point mass spring-damper models, from a single mass spring-damper system, Model 1, to a 3-layer mass spring-damper system, Model 4, were constructed using Matlab to model the mat's behavior during impact. A fifth model composed of a 3-layer mass spring-damper system was developed using visual Nastran 4D. The results showed that Models 4 and 5 were able to match the loading phase of the impact with simulation times of less than 1 second for Model 4 and 28 seconds for Model 5. Both Models 4 and 5 successfully reproduced the key force-time characteristics of the mat-ground interface, such as peak forces, time of peak forces, interpeak minima and initial rates of loading, and could be incorporated into a gymnast-mat model.