A Guided, Conservative Approach for the Management of Localized Mandibular Anterior Tooth Wear

Surface Properties and Wear Resistance of Injectable and Computer-Aided Design/Computer Aided Manufacturing-Milled Resin Composite Thin Occlusal Veneers

OBJECTIVES

 This study was conducted to investigate the microhardness, surface roughness (Ra), and wear behavior of thin occlusal veneers (TOV) fabricated from different injectable composite materials and compare them to a Computer-Aided Design (CAD)/Computer-Aided Manufacturing (CAM) resin-based material.

MATERIALS AND METHODS

 A 1-mm occusal veneer preparation was done in a mandibular right second molar typodont tooth. The prepared model was duplicated to fabricate 32 replicas and divided into four groups (n = 8). Standard TOV were fabricated either indirectly from Cerasmart blocks, Cerasmart, GC (CS), or directly from Beautifil Injectable X, Shofu (BF), G-ænial Universal injectable, GC (GU), or SonicFill 2, Kerr (SF) using the injection molding technique. All the specimens were subjected to both thermomechanical cyclic loading (TMC) in a chewing simulator. Wear measurement was conducted by three-dimensional (3D) scanning of the veneered models before and after TMC, and the difference in the volume of the sample was recorded as the volumetric material loss due to wear. Ra before and after TMC and Vickers microhardness (VHN) of the tested materials were measured using standardized samples (n = 8). Representative samples from each group were investigated under a stereomicroscope and a scanning electron microscope.

STATISTICAL ANALYSIS

 One-way analysis of variance (ANOVA) was applied to detect the effect of material on VHN and wear. Two-way ANOVA was utilized to examine the impact of material and TMC on Ra. Multiple comparisons between the groups were conducted using Tukey's post hoc test (α = 0.05). The Pearson's correlation coefficient was used to determine the relationship between hardness and wear and between roughness and wear (α = 0.05).

RESULTS

 CS exhibited the highest mean VHN (p ≤ 0.001), followed by GU and SF which were statistically similar (p = 0.883) but significantly higher than BF (p < 0.001). After TMC, GU revealed the lowest Ra and volumetric wear (VW), followed by CS, BF, and SF (p < 0.5). A highly significant correlation existed between Ra and VW (p = 0.001, R 2 = 0.9803).

CONCLUSION

 The effect of TMC on the surface properties and wear resistance of the investigated TOV is material-dependent. GU injectable TOV are less influenced by TMC than CS milled TOV. In contrast, BF and SF demonstrated significant VW and Ra which might limit their clinical use as TOV.

Clinical considerations in the application of direct composite for tooth wear

Various techniques are available for the application of composite to restore worn teeth. Different techniques may be chosen based on the clinical presentation or clinician preference. However, for composite to be successful, there are numerous factors which must be considered in order to optimise the outcome. Pre-treatment steps, such as isolation for optimal moisture control and adequate surface preparation of the tooth, as well as the post build-up objectives of achieving a stable occlusion, good marginal adaptation and final aesthetics, are discussed in the paper.

Epidemiology, aetiology and prevention of tooth wear

Tooth wear is a commonly reported finding globally; however, many patients are unaware of having tooth wear. Identifying early signs of erosion, abrasion or attrition and determining the risk factors contributing to a patient's tooth wear may help to prevent further loss of enamel and dentine in the future. Appropriate prevention should be instigated, or appropriate referral made to other health professionals, when conditions such as gastroesophageal reflux or eating disorders are suspected. This paper presents the epidemiology and aetiological factors for tooth wear, as well as identifying the common clinical presentations of tooth wear. Patient perspectives on tooth wear and preventive techniques that can be utilised are also discussed.

[Aesthetic management of erosive tooth wear using injection molding technique]

In this article, on the example of a clinical case, the technique of restoring two central teeth in a patient with increased enamel erasability with highly filled fluid composite materials using injection techniques is described. The application of this technique has become possible because the new fluid composites have similar mechanical, physical and aesthetic properties to universal composite materials.

The restorative management of tooth wear involving the aesthetic zone

The aim of this article is to describe a systematic approach that facilitates the establishment of a clear and appropriate diagnosis when a dentate patient presents with tooth wear involving their aesthetic zone. It will also detail the protocols that are required to allow for the development of an acceptable aesthetic prescription within the limits of the functional constraints presented by the patient (where active restorative intervention may be indicated), as well as to communicate the manner by which this information can be transferred to ultimately enable the successful and predictable rehabilitation of the affected areas. An overview will also be provided of the tooth-coloured dental materials and restorative techniques that have been commonly applied to deliver the predictable and effective dental care of worn teeth in the aesthetic zone.