Peri-acetabular bone mineral densityin total hip replacement

Does a Monoblock Acetabular Component With a Ceramic Liner Cause More Pelvic Bone Loss Than a Conventional Modular Cementless Acetabular Component? A 2-Year Randomized Clinical Trial

BACKGROUND

Ceramic-on-ceramic bearings permit the use of large femoral head size while maintaining a favorable effect on wear rates. However, because of increased device rigidity, periprosthetic bone quality could be negatively affected due to stress shielding. The purpose of this study is to assess pelvic periprosthetic bone remodeling around a monoblock ceramic-on-ceramic acetabular component compared to that around a conventional modular metal-on-polyethylene device.

METHODS

Participants were randomized to receive hip replacement using either a porous-coated, modular metal-on-polyethylene acetabular component (n = 46) or a hydroxyapatite and titanium-coated monoblock shell with an integrated ceramic-on-ceramic bearing (n = 40). Radiographic assessments were completed preoperatively and postoperatively, and measurements of bone mineral density (BMD) using dual-energy X-ray absorptiometry with region free analysis were performed postoperatively and over 2-years of follow-up.

RESULTS

There was no significant difference in BMD between the 2 groups at baseline or over the following 2 years. At follow-up, complete shell-to-bone contact without a radiolucent line was observed in 26 (67%) of the modular devices and in 37 (93%) of monoblock (P < .001). The modular device was an independent predictor of radiolucent lines (odds ratio 19.1, P = .007). No cases underwent revision surgery for acetabular loosening.

CONCLUSION

Both the porous-coated modular and hydroxyapatite-coated monoblock acetabular components showed successful clinical results at short-term follow-up with no difference in pixel-level BMD. Using a large head monoblock device does not appear to be associated with an adverse effect on the local bone environment when compared to a modular device. NCT: NCT01558752.

Changes in periacetabular bone mineral density five years after resurfacing hip arthroplasty versus conventional total hip arthroplasty

INTRODUCTION:

We studied whether acetabular bone mineral density (BMD) is better preserved after resurfacing hip arthroplasty (RHA) versus small diameter metal-on-metal total hip arthroplasty (THA).

METHODS:

This randomised controlled trial included 82 patients. BMD was measured in 5 periprosthetic regions of interest (ROI) with dual-energy absorptiometry (DEXA) preoperatively, at 3 and 6 months, 1, 2, 3 and 5 years postoperative. 34 RHA and 26 THA had a complete 5 years follow-up. 1 RHA and 1 THA were revised due to pseudotumour formation, 2 THA were revised because of recurrent dislocations and 1 RHA for avascular necrosis.

RESULTS:

Overall an initial decrease in BMD was observed for both implants, stabilising after 2 years. 5 years after RHA a BMD change of +1% in upper cranial, -4% ( p < 0.01) in cranial, -8% ( p < 0.01) in craniomedial, -7% ( p < 0.01) in medial and +4% in caudal ROI compared to baseline values was seen. 5 years after THA a BMD change of -3% ( p = 0.01), -13% ( p < 0.01), -21% ( p < 0.01), -11% ( p < 0.01) and -2% for each respective ROI. The observed BMD decrease in different regions was structurally favouring the RHA-cup, with significantly higher levels in the cranial and craniomedial ROI.

CONCLUSION:

Acetabular BMD is better preserved behind a rigid press-fit convex cup in RHA compared to a titanium threaded cup in conventional THA in the cranial and craniomedial ROI. Despite of a theoretical higher stress-shielding behind the stiff acetabular component in RHA, compared to the more elastic threaded titanium THA-cup, bone depletion behind the RHA component does not seem to be of major concern.

REGISTRATION:

EudraCT (2006-005610-12).

Periacetabular bone densitometry after total hip arthroplasty with highly porous titanium cups: a 2-year follow-up prospective study

INTRODUCTION

Trabecular Titanium is an advanced cellular solid structure, composed of regular multiplanar hexagonal interconnected cells that mimic the morphology of the trabecular bone. This biomaterial demonstrated improved mechanical properties and enhanced osteoinduction and osteoconduction in several in vitro and in vivo studies. The aim of this study was to assess Trabecular Titanium osseointegration by measuring periacetabular changes in bone mineral density (BMD) with dual-emission X-ray absorptiometry (DEXA).

METHODS

89 patients (91 hips) underwent primary total hip arthroplasty (THA) with acetabular Trabecular Titanium cups. Clinical (Harris Hip Score (HHS), SF-36) and radiographic assessment were performed preoperatively, and postoperatively at 7 days and at 3, 6, 12 and 24 months. DEXA analysis was performed only postoperatively, using the BMD values measured at 7 days as baselines.

RESULTS

After an initial decrease from baseline to 6 months, BMD increased and progressively stabilised in all 3 regions of interest (ROIs). Median (IQR) HHS and SF-36 increased from 48 (39-62) and 49 (37-62) preoperatively to 99 (96-100) and 86 (79-92) at 24 months, indicating a considerable improvement in terms of pain relief, functional recovery and quality of life. BMD patterns and radiographic evaluation showed evident signs of periacetabular bone remodelling and osseointegration; all cups were stable at the final follow-up without radiolucent lines, loosening or osteolysis. No revisions were performed.

CONCLUSIONS

After an initial reduction in periacetabular BMD, all 3 ROIs exhibited stabilisation or slight recovery. Although clinical outcomes and functional recovery proved satisfactory, longer follow-ups are necessary to assess this cup long-term survivorship.

Increased Mortality in Metal-on-Metal versus Non-Metal-on-Metal Primary Total Hip Arthroplasty at 10 Years and Longer Follow-Up: A Systematic Review and Meta-Analysis

IMPORTANCE

There are concerns about increased mortality in patients with metal-on-metal bearings in total hip arthroplasty (THA).

OBJECTIVE

To determine the mortality and the morbidity in patients with metal-on-metal articulations (MOM THA) compared to patients with non-metal-on-metal articulations (non-MOM THA) after primary total hip arthroplasty.

DATA SOURCES

Search of PubMed, MEDLINE, EMBASE, Web of Science, Cochrane, CINAHL, AcademicSearchPremier, ScienceDirect, Wiley and clinical trial registers through March 2015, augmented by a hand search of references from the included articles. No language restrictions were applied.

STUDY SELECTION

Two reviewers screened and identified randomised controlled trials and observational studies of primary total hip arthroplasty comparing MOM THA with non-MOM THA.

DATA EXTRACTION AND SYNTHESIS

Two reviewers independently extracted study data and assessed risk of bias. Risk differences (RD) were calculated with random effect models. Meta-regression was used to explore modifying factors.

MAIN OUTCOMES AND MEASURES

Difference in mortality and difference in morbidity expressed as revisions and medical complications between patients with MOM THA and non-MOM THA.

RESULTS

Forty-seven studies were included, comprising 4,000 THA in randomised trials and over 500,000 THA in observational studies. For mortality, random effects analysis revealed a higher pooled RD of 0.7%, 95%, confidence interval (CI) [0.0%, 2.3%], I-square 42%; the heterogeneity was explained by differences in follow-up. When restricted to studies with long term follow-up (i.e. 10 years or more), the RD for mortality was 8.5%, 95%, CI [5.8%, 11.2%]; number needed to treat was 12. Further subgroup analyses and meta-regression random effects models revealed no evidence for other moderator variables (study level covariates, e.g. resurfacing vs. non-resurfacing MOM) than follow-up duration. The quality of the evidence presented in this meta-analysis was characterized as moderate according to the CLEAR-NPT (for non-pharmacological trials) and Cochrane risk of bias Table.

CONCLUSIONS AND RELEVANCE

Meta-analysis suggests there may be an increased long-term risk of mortality and revision surgery for patients with MOM THA compared to patients with non-MOM THA.

REGISTRATION

PROSPERO 2014:CRD42014007417.

Perfusion MRI in hips with metal-on-metal and metal-on-polyethylene total hip arthroplasty: A pilot study

Objectives

Hips with metal-on-metal total hip arthroplasty (MoM THA) have a high rate of adverse local tissue reactions (ALTR), often associated with hypersensitivity reactions. Dynamic contrast-enhanced magnetic resonance imaging (DCE-MRI) measures tissue perfusion with the parameter Ktrans (volume transfer constant of contrast agent). Our purpose was 1) to evaluate the feasibility of DCE-MRI in patients with THA and 2) to compare DCE-MRI in patients with MoM bearings with metal-on-polyethylene (MoP) bearings, hypothesising that the perfusion index Ktrans in hips with MoM THA is higher than in hips with MoP THA.

Methods

In this pilot study, 16 patients with primary THA were recruited (eight MoM, eight MoP). DCE-MRI of the hip was performed at 1.5 Tesla (T). For each patient, Ktrans was computed voxel-by-voxel in all tissue lateral to the bladder. The mean Ktrans for all voxels was then calculated. These values were compared with respect to implant type and gender, and further correlated with clinical parameters.

Results

There was no significant difference between the two bearing types with both genders combined. However, dividing patients by THA bearing and gender, women with MoM bearings had the highest Ktrans values, exceeding those of women with MoP bearings (0.067 min⁻¹versus 0.053 min⁻¹; p-value < 0.05) and men with MoM bearings (0.067 min⁻¹versus 0.034 min⁻¹; p-value < 0.001). Considering only the men, patients with MoM bearings had lower Ktrans than those with MoP bearings (0.034 min⁻¹versus 0.046 min⁻¹; p < 0.05).

Conclusion

DCE-MRI is feasible to perform in tissues surrounding THA. Females with MoM THA show high Ktrans values in DCE-MRI, suggesting altered tissue perfusion kinematics which may reflect relatively greater inflammation.

Cite this article: Dr P. E. Beaule. Perfusion MRI in hips with metal-on-metal and metal-on-polyethylene total hip arthroplasty: A pilot stud. Bone Joint Res 2016;5:73–79. DOI: 10.1302/2046-3758.53.2000572.

Serum Metal Ions with a Titanium Modular Neck Total Hip Replacement System

The goal of this study is to evaluate serum levels of chromium (Cr), cobalt (Co), and titanium (Ti) within the first two years following total hip arthroplasty using a Ti modular neck system. Twenty-five patients were randomized to a metal-on-metal (MoM) bearing with an all CoCr shell, and the remaining 25 received a metal-on-polyethylene (MoP) with a Ti shell. Serum levels demonstrated increases for Cr, Co, and Ti at 1 year (P < .001). MoM had similar Ti levels to MoP hips at 1 year (P=0.11) but lower at 2 years (P=0.03). Results suggest that the passive corrosion (i.e., chemical, pitting, and crevice corrosion) of exposed non-articular metal surfaces may be a greater source of ions than the neck-stem or head-neck interfaces.