Continuous-wave bistatic laser Doppler wind sensor

Investigating Suppression of Cloud Return with a Novel Optical Configuration of a Doppler Lidar

The full-width at half-maximum or probe length of the Lorentzian weighting function of continuous-wave Doppler lidars increases quadratically with the focus distance, which results in a deterioration in the spatial resolution of measurements. What is worse, a Doppler lidar is susceptible to moving objects that are far away from the intended measurement point. Therefore, we suggest a novel configuration to mitigate these problems by deploying two co-planar quarter-wave plates with orthogonal fast axes in the conventional continuous-wave lidar system, without any change to the other optical or electronic components. If the vertically polarized laser beam that we emit goes out and its backscattered beam returns back through the same quarter-wave plate, the returned beam will become horizontally polarized. The horizontally polarized backscattered beam cannot beat with the vertically polarized local oscillator to generate a Doppler signal. However, the polarization of the returned beam will remain unchanged if the emitted beam travels out through one plate and returns through the other. In this way, the influence of a moving backscattering particle far away from the focus point can be reduced. Both theoretical and experimental results show that, in a proper configuration, the probe length of the continuous-wave lidar can be reduced by 10%, compared with that of the conventional lidar. In addition, the fat tails of the Lorentzian weighting function can be suppressed by up to 80% to reduce the return from a cloud, albeit with a large reduction (perhaps 90%) in the signal power. This investigation provides a potential method to increase the spatial resolution of Doppler wind lidars and suppress the low-hanging cloud return.

Single-electrode-based rotating triboelectric nanogenerator for harvesting energy from tires

Rotational energy is abundant and widely available in our living environment. Harvesting ambient rotational energy has attracted great attention. In this work, we report a single-electrode-based rotating triboelectric nanogenerator (SR-TENG) for converting rotational energy into electric energy. The unique advantage of introducing the single-electrode TENG is to overcome the difficulty in making the connection in harvesting rotational energy such as from a moving and rotating tire/wheel. The fabricated device consists of a rotary acrylic disc with polytetrafluoroethylene (PTFE) blades and an Al electrode fixed on the base. The systematical experiments and theoretical simulations indicate that the asymmetric SR-TENGs exhibit much better output performances than those of the symmetric TENGs at the same rotation rates. The asymmetric SR-TENG with seven PTFE units at the rotation rate of 800 r/min can deliver a maximal output voltage of 55 V and a corresponding output power of 30 μW on a load of 100 MΩ, which can directly light up tens of red light-emitting diodes. The SR-TENG has been utilized to harvest mechanical energy from rotational motion of a bicycle wheel. Furthermore, we demonstrated that the SR-TENG can be applied to scavenge wind energy and as a self-powered wind speed sensor with a sensitivity of about 0.83 V/(m/s). This study further expands the operation principle of a single-electrode-based TENG and many potential applications of TENGs for scavenging ambient rotational energy and as a self-powered environment monitoring sensor.

Triboelectric nanogenerator for harvesting wind energy and as self-powered wind vector sensor system

We report a triboelectric nanogenerator (TENG) that plays dual roles as a sustainable power source by harvesting wind energy and as a self-powered wind vector sensor system for wind speed and direction detection. By utilizing the wind-induced resonance vibration of a fluorinated ethylene-propylene film between two aluminum foils, the integrated TENGs with dimensions of 2.5 cm × 2.5 cm × 22 cm deliver an output voltage up to 100 V, an output current of 1.6 μA, and a corresponding output power of 0.16 mW under an external load of 100 MΩ, which can be used to directly light up tens of commercial light-emitting diodes. Furthermore, a self-powered wind vector sensor system has been developed based on the rationally designed TENGs, which is capable of detecting the wind direction and speed with a sensitivity of 0.09 μA/(m/s). This work greatly expands the applicability of TENGs as power sources for self-sustained electronics and also self-powered sensor systems for ambient wind detection.

Monostatic coaxial 1.5 μm laser Doppler velocimeter using a scanning Fabry-Perot interferometer

We present a laser Doppler velocimeter (LDV) in monostatic coaxial arrangement consisting of off-the-shelf telecom-grade components: a single frequency laser (wavelength λ = 1.5 μm) and a high-finesse scanning Fabry-Perot interferometer (sFPI). In contrast to previous 1.5 μm LDV systems based on heterodyne detection, our sFPI-LDV has the advantages of having large remote sensing range not limited by laser coherence, high velocity dynamic range not limited by detector bandwidth and inherent sign discrimination of Doppler shift. The more optically efficient coaxial arrangement where transmitter and receiver optics share a common axis reduces the number of components and greatly simplifies the optical alignment. However, the sensitivity to unwanted backreflections is increased. To circumvent this problem, we employ a custom optical circulator design which compared to commercial fiber-optic circulator achieves ~40 dB reduction in strength of unwanted reflections (i.e. leakage) while maintaining high optical efficiency. Experiments with a solid target demonstrate the performance of the sFPI-LDV system with high sensitivity down to pW level at present update rates up to 10 Hz.

Continuous wave synthetic low-coherence wind sensing Lidar: motionless measurement system with subsequent numerical range scanning

A continuous wave (CW) Lidar system for detection of scattering from atmospheric aerosol particles is presented which is useful in particular for remote sensing of wind velocities. It is based on a low-coherence interferometric setup powered by a synthetic broadband laser source with Gaussian power density spectrum. The laser bandwidth is electronically adjustable and determines the spatial resolution which is independent of range. The Lidar system has no moving parts. The location to be resolved can be shifted numerically after the measurement meaning that a single measurement already contains the full range information. The features of constant resolution and numerical range scanning are in sharp contrast to ordinary CW Lidar systems.

Dual-channel heterodyne measurements of atmospheric phase fluctuations

A dual-channel fiber-coupled laser heterodyne system operating at a 1.55-microm wavelength is used to investigate phase fluctuations induced on a laser beam by propagation through turbulent air. Two receivers are used to characterize spatial and temporal variations produced by a turbulent layer of air in the laboratory. The system is also used for measurements through extended turbulence along an 80-m outdoor atmospheric path. Phase structure functions, power spectral densities, and cross correlations are presented.

Lidar frequency modulation vibrometry in the presence of speckle

We report laboratory target vibration measurements that use an easily aligned and adjusted fiber-based 1.5-microm heterodyne lidar. The targets are simple spherically curved retroreflectors with well-controlled vibration frequencies and amplitudes. A rotating ground-glass screen creates Gaussian speckle. We wish to understand the modulated and fast-fading lidar returns seen from real target. We frequency demodulated the recorded laboratory data by phase differencing to provide estimates of dphi/dt, where phi is the phase of the received carrier-plus-noise phasor. Experimental results for signal strength and signal-to-noise ratio, for specific target modulation parameters, agree well with our recently developed dphi/dt correlation-function theory.

Analysis of the performance of a coherent pulsed fiber lidar for aerosol backscatter applications

The antenna and the Doppler estimation characteristics of a coherent pulsed lidar intended for short-range aerosol backscatter applications have been analyzed. The system used fiber-optic interconnects and operated at a wavelength of 1.548 microm. The range dependence of the signal for various bistatic and monostatic antenna configurations has been determined. The system operated in a low-pulse-energy, high-pulse-repetition-rate mode, and the Doppler estimates from the return signal were achieved with a multipulse accumulation procedure. The expected performance of the accumulation in this low-photocount regime was compared with the data obtained from the system, and a reasonable level of agreement was demonstrated.

Bistatic coherent laser radar signal-to-noise ratio

We investigate the signal-to-noise ratio (SNR) for a bistatic coherent laser radar (CLR) system. With a bistatic configuration, the spatial resolution is determined by the overlap of the transmit beam and the virtual backpropagated local oscillator beam. This eliminates the trade-off between range resolution and the bandwidth of the transmitted pulse inherent in monostatic systems. The presented analysis is completely general in that the expressions can be applied to both monostatic and bistatic CLR systems. The heterodyne SNR is computed under the assumption of untruncated Gaussian optics and untruncated Gaussian beam profiles. The analysis also includes the effects of refractive turbulence. The results show that, for maximum SNR, small transmit and local oscillator beam profiles (e-1 intensity radius) are desired.

Improved speckle statistics in coherent differential absorption lidar with in-fiber wavelength multiplexing

Remote detection of gaseous pollutants and other atmospheric constituents can be achieved with differential absorption lidar (DIAL) methods. The technique relies on the transmission of two or more laser wavelengths and exploits absorption features in the target gas by measuring the ratio of their detected powers to determine gas concentration. A common mode of operation is when the transmitter and receiver are collocated, and the absorption is measured over a return trip by a randomly scattering topographic target. Hence, in coherent DIAL, speckle fluctuation leads to a large uncertainty in the detected powers unless the signal is averaged over multiple correlation times, i.e., over many independent speckles. We examine a continuous-wave coherent DIAL system in which the laser wavelengths are transmitted and received by the same single-mode optical fibers. This ensures that the two wavelengths share a common spatial mode, which, for certain transmitter and target parameters, enables highly correlated speckle fluctuations to be readily achieved in practice. For a DIAL system, this gives the potential for improved accuracy in a given observation time. A theoretical analysis quantifies this benefit as a function of the degree of correlation between the two time series (which depends on wavelength separation and target depth). The results are compared with both a numerical simulation and a laboratory-based experiment.