Control of Fano asymmetry in plasmon induced transparency and its application to plasmonic waveguide modulator

A carbon nanotube metamaterial sensor showing slow light properties based on double plasmon-induced transparency

In this study, we proposed a bifunctional sensor of high sensitivity and slow light based on carbon nanotubes (CNTs). An array of left semicircular ring (LSR), right semicircular ring (RSR), and circular ring (CR) resonators are utilized to form the proposed metamaterial. The proposed structure can achieve double plasmon-induced transparency (PIT) effects under the excitation of a TM-polarization wave. The double PIT originated from the destructive interference between two bright modes and a dark mode. A coupled harmonic oscillator model is used to describe the destructive interference between the two bright modes and a dark mode, and the simulation results agree well with the calculated results. Moreover, we investigate the influence of the coupling distance, period, and flare angle on the PIT spectra. The relationship between the resonant frequencies, full width at half maximum (FWHM), amplitudes, quality factors (Q), and the coupling distance is also studied. Finally, a high sensitivity of 1.02 THz RIU-1 is obtained, and the transmission performance can be maintained at a good level when the incident angle is less than 40°. Thus, the sensor can cope with situations where electromagnetic waves are not perpendicular to the structure's surface. The maximum figure of merit (FOM) can reach about 8.26 RIU-1; to verify the slow light property of the device, the slow light performance of the proposed structure is investigated, and a maximum time delay (TD) of 22.26 ps is obtained. The proposed CNT-based metamaterial can be used in electromagnetically induced transparency applications, such as sensors, optical memory devices, and flexible terahertz functional devices.

Multi-Wavelength Selective and Broadband Near-Infrared Plasmonic Switches in Anisotropic Plasmonic Metasurfaces

Anisotropic plasmonic metasurfaces have attracted broad research interest since they possess novel optical properties superior to natural materials and their tremendous design flexibility. However, the realization of multi-wavelength selective plasmonic metasurfaces that have emerged as promising candidates to uncover multichannel optical devices remains a challenge associated with weak modulation depths and narrow operation bandwidth. Herein, we propose and numerically demonstrate near-infrared multi-wavelength selective passive plasmonic switching (PPS) that encompasses high ON/OFF ratios and strong modulation depths via multiple Fano resonances (FRs) in anisotropic plasmonic metasurfaces. Specifically, the double FRs can be fulfilled and dedicated to establishing tailorable near-infrared dual-wavelength PPS. The multiple FRs mediated by in-plane mirror asymmetries cause the emergence of triple-wavelength PPS, whereas the multiple FRs governed by in-plane rotational asymmetries avail the implementation of the quasi-bound states in the continuum-endowed multi-wavelength PPS with the ability to unfold a tunable broad bandwidth. In addition, the strong polarization effects with in-plane anisotropic properties further validate the existence of the polarization-resolved multi-wavelength PPS. Our results provide an alternative approach to foster the achievement of multifunctional meta-devices in optical communication and information processing.

Analytical investigation of unidirectional reflectionless phenomenon near the exceptional points in graphene plasmonic system

We propose a two-dimensional array made of a double-layer of vertically separated graphene nanoribbons. The transfer matrix method and coupled mode theory are utilized to quantitatively depict the transfer properties of the system. We present a way to calculate the radiative and the intrinsic loss factors, combined with finite-difference time-domain simulation, conducting the complete analytical analysis of the unidirectional reflectionless phenomenon. By adjusting the Fermi energy and the vertical distance between two graphene nanoribbons, the plasmonic resonances are successfully excited, and the unique phenomena can be realized at the exceptional points. Our research presents the potential in the field of optics and innovative technologies to create advanced optical devices that operate in the mid-infrared range, such as terahertz antennas and reflectors.

Quadruple Fano resonances in MIM waveguide structure with ring cavities for multisolution concentration sensing

In this paper, a metal-insulator-metal (MIM) waveguide structure is proposed to produce quadruple Fano resonances, which is composed of a side-coupled elliptical cavity, a half-ring cavity, a half-ring cavity with an opening, and a bus waveguide with a circular barrier. The simulation results show that the resonant wavelengths of the quadruple Fano resonances can be almost independently tuned by changing the structural parameters of the three cavities. The refractive index sensing based on different cavities is discussed, and the maximum sensitivity is 1048.6 nm/RIU with an excellent linear-sensing relationship. Finally, the simultaneous multisolution concentration sensing is demonstrated, and the sensitivities are 0.138n m L ^-1 g ^-1 for the plasma concentration, 0.120n m L ^-1 g ^-1 for the glucose solution concentration, and 0.180n m L ^-1 g ^-1 for the N H ₄ C l solution concentration. The results are conducive to promoting the applications of MIM waveguide structures in integrated optical sensing.

A Nano Refractive Index Sensing Structure for Monitoring Hemoglobin Concentration in Human Body

This paper proposes a nanosensor structure consisting of a metal-insulator-metal (MIM) waveguide with a rectangular root and a double-ring (SRRDR) with a rectangular cavity. In this paper, the cause and internal mechanism of Fano resonance are investigated by the finite element method (FEM), and the transport characteristics are optimized by changing various parameters of the structure. The results show that the structure can achieve double Fano resonance. Due to the destructive disturbance between the wideband mode of the inverted rectangle on the bus waveguide and the narrowband mode of the SRRDR, the output spectrum of the system shows an obvious asymmetric Fano diagram, and the structural parameters of the sensor have a great influence on the Fano resonance. By changing the sensitive parameters, the optimal sensitivity of the refractive index nanosensor is 2280 nm/RIU, and the coefficient of excellence (FOM) is 76.7. In addition, the proposed high-sensitivity nanosensor will be used to detect hemoglobin concentration in blood, which has positive applications for biosensors and has great potential for future nanosensing and optical integration systems.

Double Fano Resonance and Independent Regulation Characteristics in a Rectangular-like Nanotetramer Metasurface Structure

Fano resonance, which is based on a plasmonic metasurface, has many potential applications in various fields, such as biochemical sensors, slow light effect, and integrated optical circuits. In this study, a rectangular-like nanotetramer metasurface structure composed of four round-head nanorods was designed. The transmission spectrum, surface charge, and electrical field distributions of the proposed structure were simulated using the finite element method. A double Fano resonance profile was observed in the transmission spectrum. One of the Fano resonances was caused by the symmetry breaking and plasmon hybridization between the horizontal double rods, whereas the other resonance was due to the plasmonic modes' hybridization among four nanorods. These resonances could be independently tuned because of different formation mechanisms. The number of Fano resonances could be adjusted by changing the coupling distance between the horizontal and vertical rods. The results contributed to designing the highly sensitive sensors based on the plasmonic metasurface.

Unified model for plasmon-induced transparency with direct and indirect coupling in borophene-integrated metamaterials

We propose, both numerically and theoretically, a uniform model to investigate the plasmonically induced transparency effect in plasmonic metamaterial consisting of dual-layer spatially separated borophene nanoribbons array. The dynamic transfer properties of light between two borophene resonators can be effectively described by the proposed model, with which we can distinguish and connect the direct and indirect coupling schemes in the metamaterial system. By adjusting the electron density and separation of two borophene ribbons, the proposed metamaterials enable a narrow band in the near-infrared region to reach high transmission. It provides a new, to the best of our knowledge, platform for optoelectronic integrated high-performance devices in the communication band.

Dual-frequency unidirectional reflectionless propagation in a non-Hermitian graphene plasmonic waveguide-cavity coupling system

We theoretically investigate a controllable dual-frequency unidirectional reflectionlessness at exceptional points by applying external voltage in a graphene plasmonic waveguide system. The system consists of a graphene waveguide and two end-coupled resonators. COMSOL simulation results show that the reflection of edge fundamental graphene surface plasmon polaritons mode for forward (backward) incidence is near to zero at frequency 24.418 THz (20.865 THz), while that for backward (forward) incidence is 24.71% (22.945%), respectively. In addition, the non-Hermitian scattering matrix is proposed to verify the existence of double exceptional points, and the tunable unidirectional reflectionless phenomenon is also achieved by changing the Fermi level (E_f) of graphene.

On-Chip Integrated Photonic Devices Based on Phase Change Materials

Phase change materials present a unique type of materials that drastically change their electrical and optical properties on the introduction of an external electrical or optical stimulus. Although these materials have been around for some decades, they have only recently been implemented for on-chip photonic applications. Since their reinvigoration a few years ago, on-chip devices based on phase change materials have been making a lot of progress, impacting many diverse applications at a very fast pace. At present, they are found in many interesting applications including switches and modulation; however, phase change materials are deemed most essential for next-generation low-power memory devices and neuromorphic computational platforms. This review seeks to highlight the progress thus far made in on-chip devices derived from phase change materials including memory devices, neuromorphic computing, switches, and modulators.

MIM waveguide structure consisting of a semicircular resonant cavity coupled with a key-shaped resonant cavity

We describe the optical transmission properties of a surface plasmon polariton waveguide structure consisting of a metal-insulator-metal (MIM) waveguide and a semicircular resonant cavity coupled with a key-shaped resonant cavity. Finite element algorithm simulated the optical response of a MIM waveguide structure. The influence of coupling length, geometrical size, and asymmetry of the key-shaped cavity and the radius of the semicircular resonant cavity on the Fano resonance line was investigated. Results demonstrate that variation of the key-shaped cavity asymmetry leads to the appearance of dual Fano resonances. When materials with different refractive index fill in the key-shaped cavity, the MIM waveguide structure achieves a sensitivity of 1261.67 nm/RIU. This performance allows the waveguide to be used for nanoscale biosensor applications such as measuring glucose concentrations. We simulated various spiked glucose concentrations by calculating the frequency shift as the second Fano resonance line moves towards longer wavelength. Glucose concentrations were calculated from variations of the Fano resonant wavelength. The waveguide structure proposed in this paper shows impressive practical prospects for many applications in the chemical sensing and biomedical fields.

Metal-graphene hybridized plasmon induced transparency in the terahertz frequencies

In this work, metal-graphene hybridized plasmon induced transparency (PIT) is systematically studied in the proposed simple metal/dielectric/graphene system. The PIT effect is the result of the coupling between the bright dipolar modes excited in the graphene regions under the shorter metallic bars and the dark quadrupolar modes excited in the graphene regions under the longer metallic bars. The coupled Lorentz oscillator model is used to help explain the physical origin of the PIT effect. Other than being tuned by the distance and the lateral displacement of the orthogonal metallic bars, the coupling efficiency can be further enhanced by the in-phase coupling or quenched by the out-of-phase coupling between the adjacent unit cells. Reduced barrier thickness will result in the enhancement of the coupling strengths and the scaling down of the device. Finally, we show that the PIT window can be actively tuned by changing the Fermi energy of graphene. The proposed structure has potential applications in actively tunable THz modulators, sensors and filters.

Improved Optical Waveguide Microcantilever for Integrated Nanomechanical Sensor

This paper reports on an improved optical waveguide microcantilever sensor with high sensitivity. To improve the sensitivity, a buffer was introduced into the connection of the input waveguide and optical waveguide cantilever by extending the input waveguide to reduce the coupling loss of the junction. The buffer-associated optical losses were examined for different cantilever thicknesses. The optimum length of the buffer was found to be 0.97 μm for a cantilever thickness of 300 nm. With this configuration, the optical loss was reduced to about 40%, and the maximum sensitivity was more than twice that of the conventional structure.

Single-Mode Tapered Vertical SU-8 Waveguide Fabricated by E-Beam Lithography for Analyte Sensing

In this paper, we propose a novel vertical SU-8 waveguide for evanescent analyte sensing. The waveguide is designed to possess a vertical and narrow structure to generate evanescent waves on both sides of the waveguide’s surface, aimed at increasing the sensitivity by enlarging the sensing areas. We performed simulations to monitor the influence of different parameters on the waveguide’s performance, including its height and width. E-beam lithography was used to fabricate the structure, as this one-step direct writing process enables easy, fast, and high-resolution fabrication. Furthermore, it reduces the sidewall roughness and decreases the induced scattering loss, which is a major source of waveguide loss. Couplers were added to improve the coupling efficiency and alignment tolerance, and will contribute to the feasibility of a plug-and-play optical system. Optical measurements show that the transmission loss is 1.03 ± 0.19 dB/cm. The absorption sensitivity was measured to be 4.8 dB per refractive index unit (dB/RIU) for saline solutions with various concentrations.

Tapered Fiber-Optic Mach-Zehnder Interferometer for Ultra-High Sensitivity Measurement of Refractive Index

A Mach-Zehnder interferometer (MZI) based fiberoptic refractive index (RI) sensor is constructed by uniformly tapering standard single mode fiber (SMF) for RI measurement. A custom flame-based tapering machine is used to fabricate microfiber MZI sensors directly from SMFs. The fabricated MZI device does not require any splicing of fibers and shows excellent RI sensitivity. The sensor with a cladding diameter of 35.5 µm and length of 20 mm exhibits RI sensitivity of 415 nm/RIU for RI range of 1.332 to 1.384, 1103 nm/RIU for RI range of 1.384 to 1.4204 and 4234 nm/RIU for RI range of 1.4204 to 1.4408, respectively. The sensor reveals a temperature sensitivity of 0.0097 nm/°C, which is relatively low in comparison to its ultra-high RI sensitivity. The proposed inexpensive and highly sensitive optical fiber RI sensors have numerous applications in chemical and biochemical sensing fields.

Tuning Multiple Fano Resonances for On-Chip Sensors in a Plasmonic System

This paper proposed a plasmonic resonator system, consisting of a metal-insulator-metal structure and two stubs, and a Fano resonance arose in its transmittance, which resulted from the coupling between the two stubs. On the basis of the proposed structure, a circle and a ring cavity are separately added above the stubs to create different coupled plasmonic structures, providing triple and quadruple Fano resonances, respectively. Additionally, by adjusting the geometric parameters of the system, multiple Fano Resonances obtained can be tuned. The proposed structure can be served as a high efficient refractive index sensor, yielding a sensitivity of 2000 nm/RIU and figure of merit (FOM) of 4.05×104 and performing better than most of the similar structures. It is believed that the proposed structure may support substantial applications for on-chip sensors, slow light and nonlinear devices in highly integrated photonic circuits.

Theoretical Investigation of a Highly Sensitive Refractive-Index Sensor Based on TM₀ Waveguide Mode Resonance Excited in an Asymmetric Metal-Cladding Dielectric Waveguide Structure

This study proposes a highly sensitive refractive-index (RI) sensor based on a TM₀ waveguide mode resonance excited in an asymmetric metal-cladding dielectric waveguide structure, where the analyte serves as the guiding layer. By scanning the wavelength at fixed angles of incidence, the reflection spectra of the sensor were obtained. The results showed that the resonance wavelength redshifted dramatically with increases in the analyte RI, which indicates that this approach can be used to sense both the resonance wavelength and the analyte RI. Based on this approach, we investigated the sensing properties, including the sensitivity and figure of merit, at fixed incident angles of 60° and 45°, at which the sensitivity of the sensor reached 7724.9 nm/RIU (refractive index units) and 1339 nm/RIU, respectively. Compared with surface plasmon resonance sensors, which are based on a similar structure, the proposed sensor can accept a more flexible range of incident angles and a wider sensing range of analyte RI. This approach thus has tremendous potential for use in numerous sensing domains, such as biochemical and medical analyses.

On-chip plasmon-induced transparency in THz metamaterial on a LiNbO3 subwavelength planar waveguide

We experimentally demonstrate on-chip plasmon-induced transparency at THz frequencies using a meta-structure deposited on a 50 μm-thick dielectric subwavelength waveguide. The obvious plasmon-induced transparency results from strong coupling between the respective modes of a cut wire and a double-gap split ring resonator. The simulation and experimental results are consistent. Based on our numerical simulations of the temporal evolution of plasmon-induced transparency, a π/2 phase difference at the transparency peak between the above two modes is observed, i.e., there is energy oscillating between them that exhibits Rabi oscillation-like behavior. In addition, at the transparency peak, a strong local-field enhancement effect and high transmission can be obtained simultaneously, which can be tuned by changing the separation between the cut wire and the double-gap split ring resonator. These results will facilitate the design of THz integrated photonic devices and serve as an excellent platform for nonlinear optics and sensing.

Gate-Tunable Plasmon-Induced Transparency Modulator Based on Stub-Resonator Waveguide with Epsilon-Near-Zero Materials

We demonstrate an electrically tunable ultracompact plasmonic modulator with large modulation strength (>10 dB) and a small footprint (~1 μm in length) via plasmon-induced transparency (PIT) configuration. The modulator based on a metal-oxide-semiconductor (MOS) slot waveguide structure consists of two stubs embedded on the same side of a bus waveguide forming a coupled system. Heavily n-doped indium tin oxide (ITO) is used as the semiconductor in the MOS waveguide. A large modulation strength is realized due to the formation of the epsilon-near-zero (ENZ) layer at the ITO-oxide interface at the wavelength of the modulated signal. Numerical simulation results reveal that such a significant modulation can be achieved with a small applied voltage of ~3V. This result shows promise in developing nanoscale modulators for next generation compact photonic/plasmonic integrated circuits.

Tunable multiple Fano resonance employing polarization-selective excitation of coupled surface-mode and nanoslit antenna resonance in plasmonic nanostructures

Modeling and tailoring of multispectral Fano resonance in plasmonic system employing nanoslit-antenna array is demonstrated and investigated. Efficient control of the multiple Fano profile can be manipulated, where the overall spectral is achieved by the separate contributions from the fundamental subgroups plasmonic resonance eigenstates. A polarization-selective strategy on nano-antennas resonance is proposed to shed light on the efficient manipulation of the multiple Fano resonances. Theory prediction of TM₋₁ surface mode excited in the system and thorough dispersion analysis of the supported Bloch modes provides evidence for understanding the origin of the transmission spectra. Compact nanophotonics planar optical linear-polarizer in the proposed nanostructure is investigated and demonstrated, where flexible Fano resonance control over the profile, linewidth and spectral contrast is appealing for applications such as sensing, switches and multifunctional nanophotonics devices.

Fano Resonance in an Asymmetric MIM Waveguide Structure and Its Application in a Refractive Index Nanosensor

Herein, the design for a tunable plasmonic refractive index nanosensor is presented. The sensor is composed of a metal–insulator–metal waveguide with a baffle and a circular split-ring resonator cavity. Analysis of transmission characteristics of the sensor structures was performed using the finite element method, and the influence of the structure parameters on the sensing characteristics of the sensor is studied in detail. The calculation results show that the structure can realize dual Fano resonance, and the structural parameters of the sensor have different effects on Fano resonance. The peak position and the line shape of the resonance can be adjusted by altering the sensitive parameters. The maximum value of structural sensitivity was found to be 1114.3 nm/RIU, with a figure of merit of 55.71. The results indicate that the proposed structure can be applied to optical integrated circuits, particularly in high sensitivity nanosensors.

Dual-band unidirectional reflectionlessness at exceptional points in a plasmonic waveguide system based on near-field coupling between two resonators

Dual-band unidirectional reflectionlessness at exceptional points is investigated theoretically in a non-Hermitian plasmonic waveguide system, based on near-field coupling by using only two resonators. The system consists of a metal-insulator-metal waveguide end-coupled to two nanohole resonators. The reflectivity for the forward (backward) direction is ∼0 (∼0) at frequency 205.20 THz (194.56 THz), while for the backward (forward) direction it is ∼0.76 (∼0.78). Moreover, the quality factors of the dual-band unidirectional reflectionlessness for forward and backward directions can reach ∼132 and ∼137, respectively.

Magnetic-field sensor with self-reference characteristic based on a magnetic fluid and independent plasmonic dual resonances

A magnetic-field sensor with self-reference characteristic based on metal-dielectric-metal (MDM) plasmonic waveguides and a magnetic fluid (MF) is proposed and theoretically investigated. Independent dual resonances are supported by the coupled resonator-waveguide system. The physical mechanisms of dual resonances are analyzed by the temporal coupled-mode theory. The transmission response to an external magnetic field is explored by using the remarkable tunability of the refractive index of the MF. Based on the different dependence of two resonances on the external field, a magnetic-field sensor with self-reference characteristic is achieved. The magnetic-field nanosensor shows an excellent performance with a high sensitivity of 27 pm/Oe, i.e., 270 pm/mT. The proposed sensor takes advantage of the refractive-index tunability of the MF and the compactness of the MDM waveguide structure. This research may open new opportunities to design nanoscale magnetic sensors with good performance.

Fano resonance between coherent acoustic phonon oscillations and electronic states near the bandgap of photoexcited GaAs

Impulsive photo-excitation of solids results in a travelling strain pulse which manifests itself as coherent acoustic phonon oscillations. These oscillations have been extensively studied using time-resolved pump-probe spectroscopy. In the present work, we report the generation of extremely long-lived, coherent longitudinal acoustic phonon oscillations in intrinsic GaAs (100), with clear and unambiguous evidence of Fano interference between these oscillations and the continuum of electronic states close to the bandgap. Fano resonance is a widespread phenomenon observed in atomic systems and condensed media that arises from quantum interference between a continuum of quantum states and a discrete quantum state. Among other techniques, Fano resonance has been investigated with respect to optical phonons studied with Raman Spectroscopy. In the present work, we investigate Fano resonance in coherent phonon oscillations generated without the aid of any capping layer, dopants or substrate/interface effects. Since Fano resonance is sensitive to changes in electronic structure, doping and defects, these observations are important to the field of picosecond ultrasonics which is used for non-destructive depth profiling of solids and for carrier diffusion studies.

A Plasmonic Chip-Scale Refractive Index Sensor Design Based on Multiple Fano Resonances

In this paper, multiple Fano resonances preferred in the refractive index sensing area are achieved based on sub-wavelength metal-insulator-metal (MIM) waveguides. Two slot cavities, which are placed between or above the MIM waveguides, can support the bright modes or the dark modes, respectively. Owing to the mode interferences, dual Fano resonances with obvious asymmetrical spectral responses are achieved. High sensitivity and high figure of merit are investigated by using the finite-difference time-domain (FDTD) method. In view of the development of chip-scale integrated photonics, two extra slot cavities are successively added to the structure, and consequently, three and four ultra-sharp Fano peaks with considerable performances are obtained, respectively. It is believed that this proposed structure can find important applications in the on-chip optical sensing and optical communication areas.

Plasmonic Multichannel Refractive Index Sensor Based on Subwavelength Tangent-Ring Metal⁻Insulator⁻Metal Waveguide

In this paper, a multichannel refractive index sensor based on a subwavelength metal⁻insulator⁻metal (MIM) waveguide coupled with tangent-ring resonators is proposed. When two tangent-ring resonators were placed above the MIM waveguide, Fano resonance with asymmetrical line shape appeared in the transmission spectrum due to the interference between the light⁻dark resonant modes. The sensitivity and figure of merit were as high as 880 nm/RIU and 964, respectively. Through adding more tangent-ring resonators, multiple Fano resonances with ultrasharp peaks/dips were achieved in the wavelength range of 800⁻2000 nm. Besides, negative group delays were also observed in the Fano resonant dips. Two-dimensional finite-difference time-domain (FDTD) method was used to simulate and analyze the performances of the proposed structures. These kinds of multiring structures can find important applications in the on-chip optical sensing and optical communication areas.

Refractive Index Sensor Based on a Metal-Insulator-Metal Waveguide Coupled with a Symmetric Structure

In this study, a new refractive index sensor based on a metal–insulator–metal waveguide coupled with a notched ring resonator and stub is designed. The finite element method is used to study the propagation characteristics of the sensor. According to the calculation results, the transmission spectrum exhibits a typical Fano resonance shape. The phenomenon of Fano resonance is caused by the coupling between the broadband spectrum and narrowband spectrum. In the design, the broadband spectrum signal is generated by the stub, while the narrowband spectrum signal is generated by the notched ring resonator. In addition, the structural parameters of the resonators and the structure filled with media of different refractive indices are varied to study the sensing properties. The maximum achieved sensitivity of the sensor reached 1071.4 nm/RIU. The results reveal potential applications of the coupled system in the field of sensors.

Plasmon-induced transparency based on a triangle cavity coupled with an ellipse-ring resonator

In this paper, a novel compact plasmonic system is introduced to realize the phenomenon of plasmon-induced transparency. The proposed device consists of a triangle defect coupled with an ellipse-ring resonator based on a metal-insulator-metal platform. By the finite-difference time-domain method, the transmission characteristics are numerically studied in detail. In order to verify the simulation results, the coupled mode theory is utilized. In the following, the effect of geometrical parameters, namely, the major and minor radii of the ellipse-ring and the gap between cavities, are investigated. Moreover, the fundamental factors of transmission spectra including intrinsic Drude loss and refractive index of dielectric region are studied. As a result, the transmission peak is obtained near 70% and the full width at half-maximum is close to 28 nm. The sensitivity and figure of merit of the proposed structure are 860 nm/RIU and 31.6  RIU^-1, respectively. The mentioned compact structure has the ability and potential to be used in integrated optical circuits like slow light devices, nanoscale filters and nanosensors.

Dynamically tunable plasmon induced absorption in graphene-assisted metallodielectric grating

The dynamically tunable plasmon induced absorption (PIA) effect is demonstrated in a graphene-assisted metallodielectric grating structure. Two methods are employed to achieve the tunable PIA effect in the mid-infrared region: one is based on controlling the chemical potential of graphene by adjusting the gate voltage, the other is related to varying the refractive index of interlayer. Our calculated results reveal that high tunability in amplitude and bandwidth of the PIA effect can be achieved by using the above-mentioned methods. Compared with previous results, our scheme is much easier to fabricate and has significant applications in modulators, absorbers and sensors.

Dual-band unidirectional reflectionless phenomena in an ultracompact non-Hermitian plasmonic waveguide system based on near-field coupling

Dual-band unidirectional reflectionlessness and coherent perfect absorption (CPA) are demonstrated in a non-Hermitian plasmonic waveguide system based on near-field coupling between a single resonator and the resonant modes of two resonators showing an electromagnetically induced-transparency-like (EIT-like) effect. The non-Hermitian plasmonic system consists of three metal-insulator-metal (MIM) resonators coupled to a MIM plasmonic waveguide.

Analogue of electromagnetically induced absorption with double absorption windows in a plasmonic system

We report the observation of an analog of double electromagnetically induced absorption (EIA) in a plasmonic system consisting of two disk resonators side-coupled to a discrete metal-insulator-metal (MIM) waveguide. The finite-difference time-domain (FDTD) simulation calculations show that two absorption windows are obtained and can be easily tuned by adjusting the parameters of the two resonance cavities. The consistence between the coupled-model theory and FDTD simulation results verify the feasibility of the proposed system. Since the scheme is easy to be fabricated, our proposed configuration may thus be applied to narrow-band filtering, absorptive switching, and absorber applications.

Tunable Fano Resonance in Asymmetric MIM Waveguide Structure

A plasmonic waveguide coupled system that uses a metal-insulator-metal (MIM) waveguide with two silver baffles and a coupled ring cavity is proposed in this study. The transmission properties of the plasmonic system were investigated using the finite element method. The simulation results show a Fano profile in the transmission spectrum, which was caused by the interaction of the broadband resonance of the Fabry-Perot (F-P) cavity and the narrow band resonance of the ring cavity. The Fabry-Perot (F-P) cavity in this case was formed by two silver baffles dividing the MIM waveguide. The maximum sensitivity of 718 nm/RIU and the maximum figure of merit of 4354 were achieved. Furthermore, the effects of the structural parameters of the F-P cavity and the ring cavity on the transmission properties of the plasmonic system were analyzed. The results can provide a guide for designing highly sensitive on-chip sensors based on surface plasmon polaritons.

Refractive Index Sensor Based on Fano Resonances in Metal-Insulator-Metal Waveguides Coupled with Resonators

A surface plasmon polariton refractive index sensor based on Fano resonances in metal–insulator–metal (MIM) waveguides coupled with rectangular and ring resonators is proposed and numerically investigated using a finite element method. Fano resonances are observed in the transmission spectra, which result from the coupling between the narrow-band spectral response in the ring resonator and the broadband spectral response in the rectangular resonator. Results are analyzed using coupled-mode theory based on transmission line theory. The coupled mode theory is employed to explain the Fano resonance effect, and the analytical result is in good agreement with the simulation result. The results show that with an increase in the refractive index of the fill dielectric material in the slot of the system, the Fano resonance peak exhibits a remarkable red shift, and the highest value of sensitivity (S) is 1125 nm/RIU, RIU means refractive index unit. Furthermore, the coupled MIM waveguide structure can be integrated with other photonic devices at the chip scale. The results can provide a guide for future applications of this structure.

Tailored Fano resonance and localized electromagnetic field enhancement in Ag gratings

Metallic gratings can support Fano resonances when illuminated with EM radiation, and their characteristic reflectivity versus incident angle lineshape can be greatly affected by the surrounding dielectric environment and the grating geometry. By using conformal oblique incidence thin film deposition onto an optical grating substrate, it is possible to increase the grating amplitude due to shadowing effects, thereby enabling tailoring of the damping processes and electromagnetic field couplings of the Fano resonances, hence optimizing the associated localized electric field intensity. To investigate these effects we compare the optical reflectivity under resonance excitation in samples prepared by oblique angle deposition (OAD) and under normal deposition (ND) onto the same patterned surfaces. We observe that by applying OAD method, the sample exhibits a deeper and narrower reflectivity dip at resonance than that obtained under ND. This can be explained in terms of a lower damping of Fano resonance on obliquely deposited sample and leads to a stronger localized electric field. This approach opens a fabrication path for applications where tailoring the electromagnetic field induced by Fano resonance can improve the figure of merit of specific device characteristics, e.g. quantum efficiency (QE) in grating-based metallic photocathodes.

Low-dimensional gap plasmons for enhanced light-graphene interactions

Graphene plasmonics has become a highlighted research area due to the outstanding properties of deep-subwavelength plasmon excitation, long relaxation time, and electro-optical tunability. Although the giant conductivity of a graphene layer enables the low-dimensional confinement of light, the atomic scale of the layer thickness is severely mismatched with optical mode sizes, which impedes the efficient tuning of graphene plasmon modes from the degraded light-graphene overlap. Inspired by gap plasmon modes in noble metals, here we propose low-dimensional hybrid graphene gap plasmon waves for large light-graphene overlap factor. We show that gap plasmon waves exhibit improved in-plane and out-of-plane field concentrations on graphene compared to those of edge or wire-like graphene plasmons. By adjusting the chemical property of the graphene layer, efficient and linear modulation of hybrid graphene gap plasmon modes is also achieved. Our results provide potential opportunities to low-dimensional graphene plasmonic devices with strong tunability.

Tuning Fano resonances with a nano-chamber of air

By designing a polymer-film-coated asymmetric metallic slit structure that only contains one nanocavity side-coupled with a subwavelength plasmonic waveguide, the Fano resonance is realized in the experiment. The Fano resonance originates from the interference between the narrow resonant spectra of the radiative light from the nanocavity and the broad nonresonant spectra of the directly transmitted light from the slit. The lateral dimension of the asymmetric slit is only 825 nm. Due to the presence of the soft polymer film, a nano-chamber of air is constructed. Based on the opto-thermal effect, the air volume in the nano-chamber is expanded by a laser beam, which blueshifts the Fano resonance. This tunable Fano resonance in such a submicron slit structure with a nano-chamber is of importance in the highly integrated plasmonic circuits.

Tunable high quality factor in two multimode plasmonic stubs waveguide

We numerically investigate the optical characteristics of a metal-dielectric-metal (MDM) waveguide side-coupled with two identical multimode stub resonators. Double plasmon-induced transparency (PIT) peaks with narrow full width at half maximum (FWHM) and high quality factor (Q-factor) can be observed in this structure. The Q-factors of PIT peaks in two stub resonators system are larger than those in single stub resonator system. A multimode coupled-radiation oscillator theory (MC-ROT), which is derived from ROT, is proposed to analyze the spectral response in the multimode system for the first time. The analytical results are confirmed by the finite-difference time-domain (FDTD) simulation results. We can also find that the Q-factors of the two PIT peaks have an opposite evolution tendency with the change of the stubs parameters and the maximum can reach to 427. These results may provide some applications for ultrasensitive sensors, switches and efficient filters.

Tunable nanoplasmonic sensor based on the asymmetric degree of Fano resonance in MDM waveguide

We first report a simple nanoplasmonic sensor for both universal and slow-light sensing in a Fano resonance-based waveguide system. A theoretical model based on the coupling of resonant modes is provided for the inside physics mechanism, which is supported by the numerical FDTD results. The revealed evolution of the sensing property shows that the Fano asymmetric factor p plays an important role in adjusting the FOM of sensor, and a maximum of ~4800 is obtained when p = 1. Finally, the slow-light sensing in such nanoplasmonic sensor is also investigated. It is found that the contradiction between the sensing width with slow-light (SWS) and the relevant sensitivity can be resolved by tuning the Fano asymmetric factor p and the quality factor of the superradiant mode. The presented theoretical model and the pronounced features of this simple nanoplasmonic sensor, such as the tunable sensing and convenient integration, have significant applications in integrated plasmonic devices.

Spectral separation of optical spin based on antisymmetric Fano resonances

We propose a route to the spectral separation of optical spin angular momentum based on spin-dependent Fano resonances with antisymmetric spectral profiles. By developing a spin-form coupled mode theory for chiral materials, the origin of antisymmetric Fano spectra is clarified in terms of the opposite temporal phase shift for each spin, which is the result of counter-rotating spin eigenvectors. An analytical expression of a spin-density Fano parameter is derived to enable quantitative analysis of the Fano-induced spin separation in the spectral domain. As an application, we demonstrate optical spin switching utilizing the extreme spectral sensitivity of the spin-density reversal. Our result paves a path toward the conservative spectral separation of spins without any need of the magneto-optical effect or circular dichroism, achieving excellent purity in spin density superior to conventional approaches based on circular dichroism.

Polarization-selective dynamically tunable multispectral Fano resonances: decomposing of subgroup plasmonic resonances

We analyze the design of near infrared all-optical controllable and dynamically tunable multispectral Fano resonances based on subgroup decomposition of plasmonic resonances in hybrid nanoslits antenna plasmonic system. The theoretical investigation complemented with numerical simulations show that the Fano resonance lines shape can be tailored efficiently and continuously with the nanoslits geometry and the variation of the polarization states of the incident light. The subgroup decomposition of the spectral profile and the modification of plasmonic resonances lineshape that leads to the Fano-type profile of transmission is investigated and revealed. The separate contribution from individual spectral of single-slit array subgroup is attributed to the resulting overall multispectral Fano lineshape of the proposed T-shaped slits array at their corresponding spectral peaks zone. The polarization-selective tunability of the multispectral Fano resonances in the planar hybrid plasmonic system creates new avenues for designing multi-channel multi-wavelength tunable Fano effect.

A graphene based tunable terahertz sensor with double Fano resonances

We propose an ultrasensitive terahertz (THz) sensor consisting of a subwavelength graphene disk and an annular gold ring within a unit cell. The interference between the resonances arising from the graphene disk and the gold ring gives rise to Fano type resonances and enables ultrasensitive sensing. Our full wave electromagnetic simulations show frequency sensitivity as high as 1.9082 THz per refractive index unit (RIU) and a figure of merit (FOM) of 6.5662. Furthermore, the sensing range can be actively tuned by adjusting the Fermi level of graphene.

Tunable control of electromagnetically induced transparency analogue in a compact graphene-based waveguide

An easily-integrated compact graphene-based waveguide structure is proposed to achieve an analogue of electromagnetically induced transparency (EIT) effect at terahertz frequencies. The structure is composed of a graphene waveguide and two identical-shape graphene ribbons located parallel on the same side of the waveguide at different distances, in which the closer and the farther ribbons behave as the bright and the dark resonators, respectively. The EIT-like effect is caused by the destructive interference of the two resonators. By shifting the Fermi energy levels of ribbons, the transparency window can be dynamically tuned. The structure may offer another way for tunable integrated optical devices.

Electromagnetically induced absorption in detuned stub waveguides: a simple analytical and experimental model

We give an analytical and experimental demonstration of a classical analogue of the electromagnetic induced absorption (EIA) in a simple photonic device consisting of two stubs of lengths d1 and d2 grafted at the same site along a waveguide. By detuning the lengths of the two stubs (i.e. δ = d(2) - d(1)) we show that: (i) the amplitudes of the electromagnetic waves in the two stubs can be written following the two resonators model where each stub plays the role of a radiative resonator with low Q factor. The destructive interference between the waves in the two stubs may give rise to a sharp resonance peak with high Q factor in the transmission as well as in the absorption. (ii) The transmission coefficient around the resonance induced by the stubs can be written following a Fano-like form. In particular, we give an explicit expression of the position, width and Fano parameter of the resonances as a function of δ. (iii) By taking into account the loss in the waveguides, we show that at the transmission resonance, the transmission (reflection) increases (decreases) as a function of δ. Whereas the absorption goes through a maximum around 0.5 for a threshold value δth which depends on the attenuation in the system and then falls to zero. (iv) We give a comparison between the phase of the determinant of the scattering matrix, the so-called Friedel phase and the phase of the transmission amplitude. (v) The effect of the boundary conditions at the end of the resonators on the EIA resonance is also discussed. The analytical results are obtained by means of the Green's function method, whereas the experiments are carried out using coaxial cables in the radio-frequency regime. These results should have important consequences for designing integrated devices such as narrow-frequency optical or microwave filters and high-speed switches.

Widely tunable SPP bandgap in a nonlinear metal-insulator-metal waveguide

In this article, we propose a novel kind of widely tunable surface plasmon polaritons (SPP) bandgap in a Kerr nonlinear metal-insulator-metal waveguide. By two identical gratings, the pump beam is coupled to two opposing SPP waves, which interfere with each other and results in SPP standing wave in the region between the two gratings. The refractive index of the Kerr nonlinear material is then periodically modulated by the SPP standing wave, and a SPP bandgap is formed. The position of the SPP bandgap can be tuned from 1.4 μm to 1.75 μm by adjusting the pump wavelength, and the relationship between the transmittance contrast of the bandgap and the pump power is also studied. Comparing with existing methods that directly modulate the refractive index (RI) or the width of the waveguide, in our work, the periodic modulation of the RI comes from the interference of the pump light, which can greatly simplify the fabrication. This work may find applications in the design of novel nonlinear devices for future all-optical integrated circuits.

Nanoscale conducting oxide PlasMOStor

We experimentally demonstrate an ultracompact PlasMOStor, a plasmon slot waveguide field-effect modulator based on a transparent conducting oxide active region. By electrically modulating the conducting oxide material deposited into the gaps of highly confined plasmonic slot waveguides, we demonstrate field-effect dynamics giving rise to modulation with high dynamic range (2.71 dB/μm) and low waveguide loss (∼0.45 dB/μm). The large modulation strength is due to the large change in complex dielectric function when the signal wavelength approaches the surface plasmon resonance in the voltage-tuned conducting oxide accumulation layer. The results provide insight about the design of ultracompact, nanoscale modulators for future integrated nanophotonic circuits.

Fano resonances in THz metamaterials composed of continuous metallic wires and split ring resonators

We demonstrate theoretically and experimentally that Fano resonances can be obtained in terahertz metamaterials that are composed of periodic continuous metallic wires dressed with periodic split ring resonators. An asymmetric Fano lineshape has been found in a narrow frequency range of the transmission curve. By using a transmission line combined with lumped element model, we are able to not only fit the transmission spectra of Fano resonance which is attributed to the coupling and interference between the transmission continuum of continuous metallic wires and the bright resonant mode of split ring resonators, but also reveal the capacitance change of the split ring resonators induced frequency shift of the Fano resonance. Therefore, the proposed theoretical model shows more capabilities than conventional coupled oscillator model in the design of Fano structures. The effective parameters of group refractive index of the Fano structure are retrieved, and a large group index more than 800 is obtained at the Fano resonance, which could be used for slow light devices.

Plasmon-induced transparency in a single multimode stub resonator

We investigate electromagnetically induced transparency (EIT)-like effect in a metal-dielectric-metal (MDM) waveguide coupled to a single multimode stub resonator. Adjusting the geometrical parameters of the stub resonator, we can realize single or double plasmon-induced transparency (PIT) windows in the plasmonic structure. Moreover, the consistency between analytical results and finite difference time domain (FDTD) simulations reveals that the PIT results from the destructive interference between resonance modes in the stub resonator. Compared with previous EIT-like scheme based on MDM waveguide, the plasmonic system takes the advantages of easy fabrication and compactness. The results may open up avenues for the control of light in highly integrated optical circuits.

Independently tunable double Fano resonances in asymmetric MIM waveguide structure

In this paper, an asymmetric plasmonic structure composed of a MIM (metal-insulator-metal) waveguide and a rectangular cavity is reported, which can support double Fano resonances originating from two different mechanisms. One of Fano resonance originates from the interference between a horizontal and a vertical resonance in the rectangular cavity. And the other is induced by the asymmetry of the plasmonic structure. Just because the double Fano resonances originate from two different mechanisms, each Fano resonance can be well tuned independently by changing the parameters of the rectangular cavity. And during the tuning process, the FOMs (figure of merit) of both the Fano resonances can keep unchanged almost with large values, both larger than 650. Such, the transmission spectra of the plasmonic structure can be well modulated to form transmission window with the position and the full width at half maximum (FWHM) can be tuned freely, which is useful for the applications in sensors, nonlinear and slow-light devices.

Plasmon-induced transparency in metal-insulator-metal waveguide side-coupled with multiple cavities

We have demonstrated the analogue of electromagnetically induced transparency (EIT) in the metal-insulator-metal plasmonic waveguide, which consists of a bus waveguide side-coupled with a series of slot cavities. By finite-difference time-domain simulations, it is found that the resonance wavelength of the slot cavity can be controlled by adjusting the length of the cavity. Moreover, the EIT-like response is strongly dependent on the coupling separation between the corresponding adjacent cavities. Multiple-peak plasmon-induced transparency can be realized by cascading multiple cavities with different lengths and suitable cavity-cavity separations. This ultracompact plasmonic waveguide system may find important applications for multichannel plasmonic filter, nanoscale optical switching, and slow-light devices in highly integrated optical circuits and networks.

On-chip plasmon-induced transparency based on plasmonic coupled nanocavities

On-chip plasmon-induced transparency offers the possibility of realization of ultrahigh-speed information processing chips. Unfortunately, little experimental progress has been made to date because it is difficult to obtain on-chip plasmon-induced transparency using only a single meta-molecule in plasmonic circuits. Here, we report a simple and efficient strategy to realize on-chip plasmon-induced transparency in a nanoscale U-shaped plasmonic waveguide side-coupled nanocavity pair. High tunability in the transparency window is achieved by covering the pair with different organic polymer layers. It is possible to realize ultrafast all-optical tunability based on pump light-induced refractive index change of a graphene cover layer. Compared with previous reports, the overall feature size of the plasmonic nanostructure is reduced by more than three orders of magnitude, while ultrahigh tunability of the transparency window is maintained. This work also provides a superior platform for the study of the various physical effects and phenomena of nonlinear optics and quantum optics.

Fano resonances in a single defect nanocavity coupled with a plasmonic waveguide

Two Fano resonances are theoretically predicted in a single defect nanocavity, consisting of a rectangular cavity with a small stub defect, side-coupled with a plasmonic waveguide. These two Fano resonances are found to originate from two different mechanisms. One is caused by the excitation of a high-order resonant mode in the rectangular cavity owing to the structural breaking, and the other is attributed to the inherent resonant mode in the small stub defect. The narrow high-order mode and inherent mode couple with the broad low-order resonant mode in the rectangular cavity, giving rise to two Fano resonances. Because of the different origins, these two Fano resonances exhibit quite different responses to the variations of the structural dimensions. This has important applications in highly sensitive and multiparameter sensing in the complicated environments.