Simultaneous compression, characterization and phase stabilization of GW-level 1.4 cycle VIS-NIR femtosecond pulses using a single dispersion-scan setup

Numerical study of a convective cooling strategy for increasing safe power levels in two-photon brain imaging

Two-photon excitation fluorescence microscopy has become an effective tool for tracking neural activity in the brain at high resolutions thanks to its intrinsic optical sectioning and deep penetration capabilities. However, advanced two-photon microscopy modalities enabling high-speed and/or deep-tissue imaging necessitate high average laser powers, thus increasing the susceptibility of tissue heating due to out-of-focus absorption. Despite cooling the cranial window by maintaining the objective at a fixed temperature, average laser powers exceeding 100-200 mW have been shown to exhibit the potential for altering physiological responses of the brain. This paper proposes an enhanced cooling technique for inducing a laminar flow to the objective immersion layer while implementing duty cycles. Through a numerical study, we analyze the efficacy of heat dissipation of the proposed method and compare it with that of the conventional, fixed-temperature objective cooling technique. The results show that improved cooling could be achieved by choosing appropriate flow rates and physiologically relevant immersion cooling temperatures, potentially increasing safe laser power levels by up to three times (3×). The proposed active cooling method can provide an opportunity for faster scan speeds and enhanced signals in nonlinear deep brain imaging.

Complementary dispersive mirror pair produced in one coating run based on desired non-uniformity

We report a novel one-coating-run method for producing an octave-spanning complementary dispersive mirror (DM) pair. The anti-phase group delay dispersion (GDD) oscillations are realized by two mirrors of the DM pair due to the certain thickness difference. Both mirrors are deposited within a single coating run enabled by the non-uniformity of the ion beam sputtering coating plant, which is obtained by tuning the distance between the source target and coating substrates. Since the DM pair is produced in a single deposition run, the GDD performance is more robust against deposition errors than that of the conventional complementary DM pair, in which two separated coating runs are necessary. Moreover, the new DM pair is compatible for both laser polarizations under the same angle of incidence, which could effectively reduce the difficulties of alignment for their implementation in laser systems than the double angle DM pair. The new DM pair is successfully applied to compress pulses from a Ti: Sapphire laser system down to 4.26 fs in pulse duration.

Temporal characterization of broadband femtosecond laser pulses by surface third-harmonic dispersion scan with ptychographic retrieval

We present a new, to the best of our knowledge, variant of dispersion scan (d-scan) based on surface third-harmonic generation (STHG) and a ptychographic algorithm tailored for full retrieval (amplitude and phase) of broadband laser pulses. We demonstrate the technique by temporally measuring and compressing few-cycle pulses with 7 fs and 2.5 nJ from a Ti:sapphire oscillator, using a sapphire window as the nonlinear medium. The results are in very good agreement with standard second-harmonic d-scan measurements based on a nonlinear crystal. The intrinsically broadband and phase-matching-independent nature of STHG make this technique very suitable for the characterization of ultrashort laser pulses over a broad wavelength range extending into the mid-infrared.

Spectral phase sensitivity of frequency resolved optical switching for broadband IR pulse characterization

In this work, we demonstrate the sensitivity of the frequency-resolved optical switching (FROSt) technique to detect a small amount of spectral phase shift for the precise characterization of ultrashort laser pulses. We characterized fs pulses centered at 1.75 µm that are spectrally broadened up to 700 nm of bandwidth in a hollow-core fiber and subsequently compressed down to 2.3 optical cycle duration by propagation in the air at atmospheric pressure. By inserting thin fused silica windows of different thicknesses in the beam path, we accurately retrieve group delay dispersion (GDD) variations as small as 10 fs². Such GDD variations correspond to a change of the pulse duration of only 0.2 fs for a Fourier transform limited 2-cycle pulse at 1.75 µm (i.e., 11.8 fs). The capability to measure such tiny temporal variations thus demonstrates that the FROSt technique has sufficient sensitivity to precisely characterize single-cycle pulses.

Phase-locking of time-delayed attosecond XUV pulse pairs

We present a setup for the generation of phase-locked attosecond extreme ultraviolet (XUV) pulse pairs. The attosecond pulse pairs are generated by high harmonic generation (HHG) driven by two phase-locked near-infrared (NIR) pulses that are produced using an actively stabilized Mach-Zehnder interferometer compatible with near-single cycle pulses. The attosecond XUV pulses can be delayed over a range of 400 fs with a sub-10-as delay jitter. We validate the precision and the accuracy of the setup by XUV optical interferometry and by retrieving the energies of Rydberg states of helium in an XUV pump-NIR probe photoelectron spectroscopy experiment.

Acousto-optic modulator based dispersion scan for phase characterization and shaping of femtosecond mid-infrared pulses

Compression, shaping and characterization of broadband mid-infrared (MIR) pulses based on an acousto-optic modulator (AOM) pulse shaper is presented. Characterization of the spectral phase is achieved by an AOM-shaper based implementation of a dispersion scan (d-scan). The abilities of the setup are demonstrated by imprinting several test phases with increasing complexity on broadband MIR pulses centered at 3.2 µm and retrieval of the imprinted phases with the presented d-scan method. Phase characterization with d-scan in combination with an evolutionary algorithm allows us to compress the MIR pulses below 50 fs FWHM autocorrelation after the shaper.

Simultaneous Observation of Carrier-Specific Redistribution and Coherent Lattice Dynamics in 2H-MoTe2 with Femtosecond Core-Level Spectroscopy

We employ few-femtosecond extreme ultraviolet (XUV) transient absorption spectroscopy to reveal simultaneously the intra- and interband carrier relaxation and the light-induced structural dynamics in nanoscale thin films of layered 2H-MoTe₂ semiconductor. By interrogating the valence electronic structure via localized Te 4d (39-46 eV) and Mo 4p (35-38 eV) core levels, the relaxation of the photoexcited hole distribution is directly observed in real time. We obtain hole thermalization and cooling times of 15 ± 5 fs and 380 ± 90 fs, respectively, and an electron-hole recombination time of 1.5 ± 0.1 ps. Furthermore, excitations of coherent out-of-plane A_1g (5.1 THz) and in-plane E_1g (3.7 THz) lattice vibrations are visualized through oscillations in the XUV absorption spectra. By comparison to Bethe-Salpeter equation simulations, the spectral changes are mapped to real-space excited-state displacements of the lattice along the dominant A_1g coordinate. By directly and simultaneously probing the excited carrier distribution dynamics and accompanying femtosecond lattice displacement in 2H-MoTe₂ within a single experiment, our work provides a benchmark for understanding the interplay between electronic and structural dynamics in photoexcited nanomaterials.

Compact in-line temporal measurement of laser pulses with amplitude swing

A method of ultrashort laser pulse reconstruction is presented, consisting on the analysis of the nonlinear signal obtained from the interference of the pulse with a replica of itself at a given time delay while varying the relative amplitude between the pulses. The resulting spectral traces are analyzed both analytically and numerically, showing the encoding of the input pulse spectral phase. A reconstruction algorithm is discussed and applied to extract the spectral phase and, jointly to the measured spectral amplitude, reconstructing the pulse. In order to validate the technique, an experimental in-line implementation of the characterization concept is compared to the results from a stablished technique, obtaining a good agreement at different input pulse cases. In sum, a new technique is presented, showing the capability to reconstruct a broad range of temporal pulse durations while its implementation is robust and straightforward, able to be easily adapted to diverse pulse duration and central wavelength ranges.

Detection and elimination of pulse train instabilities in broadband fibre lasers using dispersion scan

We use self-calibrating dispersion scan to experimentally detect and quantify the presence of pulse train instabilities in ultrashort laser pulse trains. We numerically test our approach against two different types of pulse instability, namely second-order phase fluctuations and random phase instability, where the introduction of an adequate metric enables univocally quantifying the amount of instability. The approach is experimentally demonstrated with a supercontinuum fibre laser, where we observe and identify pulse train instabilities due to nonlinear propagation effects under anomalous dispersion conditions in the photonic crystal fibre used for spectral broadening. By replacing the latter with an all-normal dispersion fibre, we effectively correct the pulse train instability and increase the bandwidth of the generated coherent spectrum. This is further confirmed by temporal compression and measurement of the output pulses down to 15 fs using dispersion scan.

Efficient table-top dual-wavelength beamline for ultrafast transient absorption spectroscopy in the soft X-ray region

We present a table-top beamline providing a soft X-ray supercontinuum extending up to 370 eV from high-order harmonic generation with sub-13 fs 1300 nm driving pulses and simultaneous production of sub-5 fs pulses centered at 800 nm. Optimization of high harmonic generation in a long and dense gas medium yields a photon flux of  ~ 1.4 × 106 photons/s/1% bandwidth at 300 eV. The temporal resolution of X-ray transient absorption experiments with this beamline is measured to be 11 fs for 800 nm excitation. This dual-wavelength approach, combined with high flux and high spectral and temporal resolution soft X-ray absorption spectroscopy, is a new route to the study of ultrafast electronic dynamics in carbon-containing molecules and materials at the carbon K-edge.

Subcycle mid-infrared coherent transients at 4 MHz repetition rate applicable to light-wave-driven scanning tunneling microscopy

We produce subcycle mid-infrared (MIR) pulses at a 4 MHz repetition rate via the optical rectification (OR) of sub-10 fs near-infrared pulses delivered by an optical parametric chirped pulse amplifier. The coherent MIR pulses generated in a GaSe crystal under an ultrabroadband phase-matching condition contain only 0.58-0.85 oscillation cycles within the full width at half-maximum of the intensity envelope. The use of OR enables excellent phase stability of 56 mrad over 5.6 h, which is confirmed by field-resolved detection using electro-optic sampling. An electromagnetic simulation using a finite integration technique reveals that the peak field strength can easily exceed 10 V/nm owing to the field enhancement resulting from focusing MIR pulses onto a tunnel junction.

Generation of a single-cycle pulse using a two-stage compressor and its temporal characterization using a tunnelling ionization method

A single-cycle laser pulse was generated using a two-stage compressor and characterized using a pulse characterization technique based on tunnelling ionization. A 25-fs, 800-nm laser pulse was compressed to 5.5 fs using a gas-filled hollow-core fibre and a set of chirped mirrors. The laser pulse was further compressed, down to the single-cycle limit by propagation through multiple fused-silica plates and another set of chirped mirrors. The two-stage compressor mitigates the development of higher-order dispersion during spectral broadening. Thus, a single-cycle pulse was generated by compensating the second-order dispersion using chirped mirrors. The duration of the single-cycle pulse was 2.5 fs, while its transform-limited duration was 2.2 fs. A continuum extreme ultraviolet spectrum was obtained through high-harmonic generation without applying any temporal gating technique. The continuum spectrum was shown to have a strong dependence on the carrier-envelope phase of the laser pulse, confirming the generation of a single-cycle pulse.

All-optical measurement of the complete waveform of octave-spanning ultrashort light pulses

We demonstrate the complete temporal characterization of the optical waveform of visible near-infrared octave-spanning ultrashort laser pulses, using an all-optical, all-solid-state, and fully inline dispersion-scan device based only on second-harmonic generation.

Direct measurement of intense sub-4-fs pulses in a gas target by 3rd-harmonic dispersion-scan

We demonstrate the on-target temporal characterization of sub-4-fs pulses by third-harmonic dispersion-scan, using a minimal in-line setup where a gas target optimized for high-harmonic generation doubles as nonlinear medium, obtaining excellent agreement with independent SEA-F-SPIDER measurements.

Self-calibrating d-scan: measuring ultrashort laser pulses on-target using an arbitrary pulse compressor

In most applications of ultrashort pulse lasers, temporal compressors are used to achieve a desired pulse duration in a target or sample, and precise temporal characterization is important. The dispersion-scan (d-scan) pulse characterization technique usually involves using glass wedges to impart variable, well-defined amounts of dispersion to the pulses, while measuring the spectrum of a nonlinear signal produced by those pulses. This works very well for broadband few-cycle pulses, but longer, narrower bandwidth pulses are much more difficult to measure this way. Here we demonstrate the concept of self-calibrating d-scan, which extends the applicability of the d-scan technique to pulses of arbitrary duration, enabling their complete measurement without prior knowledge of the introduced dispersion. In particular, we show that the pulse compressors already employed in chirped pulse amplification (CPA) systems can be used to simultaneously compress and measure the temporal profile of the output pulses on-target in a simple way, without the need of additional diagnostics or calibrations, while at the same time calibrating the often-unknown differential dispersion of the compressor itself. We demonstrate the technique through simulations and experiments under known conditions. Finally, we apply it to the measurement and compression of 27.5 fs pulses from a CPA laser.

Universal route to optimal few- to single-cycle pulse generation in hollow-core fiber compressors

Gas-filled hollow-core fiber (HCF) pulse post-compressors generating few- to single-cycle pulses are a key enabling tool for attosecond science and ultrafast spectroscopy. Achieving optimum performance in this regime can be extremely challenging due to the ultra-broad bandwidth of the pulses and the need of an adequate temporal diagnostic. These difficulties have hindered the full exploitation of HCF post-compressors, namely the generation of stable and high-quality near-Fourier-transform-limited pulses. Here we show that, independently of conditions such as the type of gas or the laser system used, there is a universal route to obtain the shortest stable output pulse down to the single-cycle regime. Numerical simulations and experimental measurements performed with the dispersion-scan technique reveal that, in quite general conditions, post-compressed pulses exhibit a residual third-order dispersion intrinsic to optimum nonlinear propagation within the fiber, in agreement with measurements independently performed in several laboratories around the world. The understanding of this effect and its adequate correction, e.g. using simple transparent optical media, enables achieving high-quality post-compressed pulses with only minor changes in existing setups. These optimized sources have impact in many fields of science and technology and should enable new and exciting applications in the few- to single-cycle pulse regime.

Strategies for achieving intense single-cycle pulses with in-line post-compression setups

Intense few- and single-cycle pulses are powerful tools in different fields of science Today, third- and higher-order terms in the remnant spectral phase of the pulses remain a major obstacle for obtaining high-quality few- and single-cycle pulses from in-line post-compression setups. In this Letter, we show how input pulse shaping can successfully be applied to standard post-compression setups to minimize the occurrence of high-order phase components during nonlinear propagation and to directly obtain pulses with durations down to 3 fs. Furthermore, by combining this pulse shaping of the input pulse with new-generation broadband chirped mirrors and material addition for remnant third-order phase correction, pulses down to 2.2 fs duration have been measured.

Compact single-shot d-scan setup for the characterization of few-cycle laser pulses

We present a compact implementation of the ultrashort pulse measurement technique based on dispersion scans (d-scan), allowing single-shot measurement of few-cycle pulses. The main novelty in our design, making our setup extremely compact and simple, is the use, after a prism, of a spherical mirror in an off-axis geometry. The intentionally introduced strong astigmatism makes it possible to image the output of the crystal in one direction while focusing it in the other direction, resulting in the output face of the prism being imaged into a line in the second-harmonic crystal. The technique is validated by comparing measured dispersion scans, retrieved spectral phases and temporal profiles of this single-shot system with standard d-scan results.

Inline self-diffraction dispersion-scan of over octave-spanning pulses in the single-cycle regime

We present an implementation of dispersion-scan based on self-diffraction (SD d-scan) and apply it to the measurement of over octave-spanning sub-4-fs pulses. The results are compared with second-harmonic generation (SHG) d-scan. The efficiency of the SD process is derived theoretically and compared with the spectral response retrieved by the d-scan algorithm. The new SD d-scan has a robust inline setup and enables measuring pulses with over-octave spectra, single-cycle durations, and wavelength ranges beyond those of SHG crystals, such as the ultraviolet and the deep-ultraviolet.

Interferometric time-domain ptychography for ultrafast pulse characterization

A novel pulse characterization method is presented, favorably combining interferometric frequency-resolved optical gating (FROG) and time-domain ptychography. This new variant is named ptychographic-interferometric frequency-resolved optical gating (πFROG). The measurement device is simple, bearing similarity to standard second-harmonic FROG, yet with a collinear beam geometry and an added bandpass filter in one of the correlator arms. The collinear beam geometry allows tight focusing and circumvents possible geometrical distortion effects of noncollinear methods, making πFROG especially suitable for the characterization of unamplified few-cycle pulses. Moreover, the direction-of-time ambiguity afflicting most second-order FROG variants is eliminated. Possible group delay dispersion of pulses leads to a characteristic tilt in the πFROG traces, allowing the detection of uncompensated dispersion without a retrieval. Using nanojoule, three-cycle pulses at 800 nm, the πFROG method is tested, and the results are compared with spectral phase interferometry for direct electric field reconstruction measurements. Measured pulse durations agree within a fraction of a femtosecond. As a further test, the πFROG measurements are repeated with added group delay dispersion, and found to accurately reproduce the dispersion computed with Sellmeier equations.

53 W average power CEP-stabilized OPCPA system delivering 5.5 TW few cycle pulses at 1 kHz repetition rate

We present a high peak and average power optical parametric chirped pulse amplification system driven by diode-pumped Yb:KGW and Nd:YAG lasers running at 1 kHz repetition rate. The advanced architecture of the system allows us to achieve >53 W average power combined with 5.5 TW peak power, along with sub-220 mrad CEP stability and sub-9 fs pulse duration at a center wavelength around 880 nm. Broadband, background-free, passively CEP stabilized seed pulses are produced in a series of cascaded optical parametric amplifiers pumped by the Yb:KGW laser, while a diode-pumped Nd:YAG laser system provides multi-mJ pump pulses for power amplification stages. Excellent stability of output parameters over 16 hours of continuous operation is demonstrated.

Generating high-contrast, near single-cycle waveforms with third-order dispersion compensation

Femtosecond laser pulses lasting only a few optical periods hold the potential for probing and manipulating the electronic degrees of freedom within matter. However, the generation of high-contrast, few-cycle pulses in the high power limit still remains nontrivial. In this Letter, we present the application of ammonium dihydrogen phosphate (ADP) as an optical medium for compensating for the higher-order dispersion of a carrier-envelope stable few-cycle waveform centered at 735 nm. The ADP crystal is capable of removing the residual third-order dispersion present in the spectral phase of an input pulse, resulting in near-transform-limited 2.9 fs pulses lasting only 1.2 optical cycles in duration. By utilizing these high-contrast, few-cycle pulses for high-harmonic generation, we are able to produce nanojoule-scale, isolated attosecond pulses.

Simultaneous generation of sub-5-femtosecond 400 nm and 800 nm pulses for attosecond extreme ultraviolet pump-probe spectroscopy

Few-cycle laser pulses with wavelengths centered at 400 nm and 800 nm are simultaneously obtained through wavelength separation of ultrashort, spectrally broadened Vis-NIR laser pulses spanning 350-1100 nm wavelengths. The 400 nm and 800 nm pulses are separately compressed, yielding pulses with 4.4 fs and 3.8 fs duration, respectively. The pulse energy exceeds 5 μJ for the 400 nm pulses and 750 μJ for the 800 nm pulses. Intense 400 nm few-cycle pulses have a broad range of applications in nonlinear optical spectroscopy, which include the study of photochemical dynamics, semiconductors, and photovoltaic materials on few-femtosecond to attosecond time scales. The ultrashort 400 nm few-cycle pulses generated here not only extend the spectral range of the optical pulse for NIR-XUV attosecond pump-probe spectroscopy but also pave the way for two-color, three-pulse, multidimensional optical-XUV spectroscopy experiments.

Broadband 7-fs diffractive-optic-based 2D electronic spectroscopy using hollow-core fiber compression

We demonstrate noncollinear coherent two-dimensional (2D) electronic spectroscopy for which broadband pulses are generated in an argon-filled hollow-core fiber pumped by a 1-kHz Ti:Sapphire laser. Compression is achieved to 7 fs duration (TG-FROG) using dispersive mirrors. The hollow fiber provides a clean spatial profile and smooth spectral shape in the 500-700 nm region. The diffractive-optic-based design of the 2D spectrometer avoids directional filtering distortions and temporal broadening from time smearing. For demonstration we record data of cresyl-violet perchlorate in ethanol and use phasing to obtain broadband absorptive 2D spectra. The resulting quantum beating as a function of population time is consistent with literature data.

A Dual-Colour Architecture for Pump-Probe Spectroscopy of Ultrafast Magnetization Dynamics in the Sub-10-femtosecond Range

Current time-resolution-limited dynamic measurements clearly show the need for improved techniques to access processes on the sub-10-femtosecond timescale. To access this regime, we have designed and constructed a state-of-the-art time-resolved magneto-optic Kerr effect apparatus, based on a new dual-color scheme, for the measurement of ultrafast demagnetization and precessional dynamics in magnetic materials. This system can operate well below the current temporal ranges reported in the literature, which typically lie in the region of around 50 fs and above. We have used a dual-colour scheme, based on ultra broadband hollow-core fibre and chirped mirror pulse compression techniques, to obtain unprecedented sub-8-fs pump and probe pulse durations at the sample plane. To demonstrate the capabilities of this system for ultrafast demagnetization and precessional dynamics studies, we have performed measurements in a ferrimagnetic GdFeCo thin film. Our study has shown that the magnetization shows a sudden drop within the first picosecond after the pump pulse, a fast recovery (remagnetization) within a few picoseconds, followed by a clear oscillation or precession during a slower magnetization recovery. Moreover, we have experimentally confirmed for the first time that a sub-10-fs pulse is able to efficiently excite a magnetic system such as GdFeCo.

Single-shot implementation of dispersion-scan for the characterization of ultrashort laser pulses

We demonstrate a single-shot ultrafast diagnostic, based on the dispersion-scan (d-scan) technique. In this implementation, rather than translating wedges to vary the dispersion as in scanning d-scan, the pulse to be measured experiences a spatially varying amount of dispersion in a prism. The resulting beam is then imaged into a second-harmonic generation crystal and an imaging spectrometer is used to measure the two-dimensional trace, which is analyzed using the d-scan retrieval algorithm. We compare the single-shot implementation with the scanning d-scan for the measurement of sub-3.5-fs pulses from a hollow core fiber pulse compressor. We show that the retrieval algorithm used to extract amplitude and phase of the pulse provides comparable results, proving the validity of the new single-shot implementation in the near single-cycle regime.

Carrier-envelope-phase insensitivity in high-order harmonic generation driven by few-cycle laser pulses

We present evidence for self-stabilization of the relative spectral phase of high-order harmonic emission against intensity variations of the driving field. Our results demonstrate that, near the laser focus, phase matching of the harmonic field from a macroscopic target can compensate for the intensity dependence of the intrinsic phase of the harmonics emitted by a single radiator. As a consequence, we show experimentally and theoretically the insensitivity of the harmonic spectra produced at the laser focus against variations of the carrier-envelope phase (CEP) of a sub-two-cycle driving field. In addition, the associated attosecond pulse trains exhibit phase locking against CEP changes of the few-cycle driver.