1
|
Liu M, Jiang M, Zhao Q, Tang K, Sha S, Li B, Kan C, Shi DN. Ultraviolet Exciton-Polariton Light-Emitting Diode in a ZnO Microwire Homojunction. ACS APPLIED MATERIALS & INTERFACES 2023; 15:13258-13269. [PMID: 36866718 DOI: 10.1021/acsami.2c19806] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/18/2023]
Abstract
Low-dimensional ZnO, possessing well-defined side facets and optical gain properties, has emerged as a promising material to develop ultraviolet coherent light sources. However, the realization of electrically driven ZnO homojunction luminescence and laser devices is still a challenge due to the absence of a reliable p-type ZnO. Herein, the sample of p-type ZnO microwires doped by Sb (ZnO:Sb MWs) was synthesized individually. Subsequently, the p-type conductivity was examined using a single-MW field-effect transistor. Upon optical pumping, a ZnO:Sb MW showing a regular hexagonal cross-section and smooth sidewall facets can feature as an optical microcavity, which is evidenced by the achievement of whispering-gallery-mode lasing. By combining an n-type ZnO layer, a single ZnO:Sb MW homojunction light-emitting diode (LED), which exhibited a typical ultraviolet emission at a wavelength of 379.0 nm and a line-width of approximately 23.5 nm, was constructed. We further illustrated that strong exciton-photon coupling can occur in the as-constructed p-ZnO:Sb MW/n-ZnO homojunction LED by researching spatially resolved electroluminescence spectra, contributing to the exciton-polariton effect. Particularly, varying the cross-sectional dimensions of ZnO:Sb wires can further modulate the exciton-photon coupling strengths. We anticipate that the results can provide an effective exemplification to realize reliable p-type ZnO and tremendously promote the development of low-dimensional ZnO homojunction optoelectronic devices.
Collapse
Affiliation(s)
- Maosheng Liu
- College of Physics, MIIT Key Laboratory of Aerospace Information Materials and Physics, Key Laboratory for Intelligent Nano Materials and Devices, Nanjing University of Aeronautics and Astronautics, No. 29 Jiangjun Road, Nanjing 211106, China
| | - Mingming Jiang
- College of Physics, MIIT Key Laboratory of Aerospace Information Materials and Physics, Key Laboratory for Intelligent Nano Materials and Devices, Nanjing University of Aeronautics and Astronautics, No. 29 Jiangjun Road, Nanjing 211106, China
| | - Qinzhi Zhao
- College of Physics, MIIT Key Laboratory of Aerospace Information Materials and Physics, Key Laboratory for Intelligent Nano Materials and Devices, Nanjing University of Aeronautics and Astronautics, No. 29 Jiangjun Road, Nanjing 211106, China
| | - Kai Tang
- College of Physics, MIIT Key Laboratory of Aerospace Information Materials and Physics, Key Laboratory for Intelligent Nano Materials and Devices, Nanjing University of Aeronautics and Astronautics, No. 29 Jiangjun Road, Nanjing 211106, China
| | - Shulin Sha
- College of Physics, MIIT Key Laboratory of Aerospace Information Materials and Physics, Key Laboratory for Intelligent Nano Materials and Devices, Nanjing University of Aeronautics and Astronautics, No. 29 Jiangjun Road, Nanjing 211106, China
| | - Binghui Li
- State Key Laboratory of Luminescence and Applications, Changchun Institute of Optics Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033, China
| | - Caixia Kan
- College of Physics, MIIT Key Laboratory of Aerospace Information Materials and Physics, Key Laboratory for Intelligent Nano Materials and Devices, Nanjing University of Aeronautics and Astronautics, No. 29 Jiangjun Road, Nanjing 211106, China
| | - Da Ning Shi
- College of Physics, MIIT Key Laboratory of Aerospace Information Materials and Physics, Key Laboratory for Intelligent Nano Materials and Devices, Nanjing University of Aeronautics and Astronautics, No. 29 Jiangjun Road, Nanjing 211106, China
| |
Collapse
|
2
|
Xu H, Xu J, Jiang M, Liu M, Tang K, Kan C, Shi D. Exciton-polariton light-emitting diode based on a single ZnO superlattice microwire heterojunction with performance enhanced by Rh nanostructures. Phys Chem Chem Phys 2023; 25:5836-5848. [PMID: 36745472 DOI: 10.1039/d2cp05446a] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/18/2023]
Abstract
One-dimensional (1D) wirelike superlattice micro/nanostructures have received considerable attention for potential applications due to their versatility and capability for modulating optical and electrical characteristics. In this study, 1D superlattice microwires (MWs), which are made of undoped ZnO and Ga-doped ZnO with periodic and alternating crystalline layers (ZnO/ZnO:Ga), were synthesized individually. Under optical excitation, a series of resonance peaks in the photoluminescence spectrum can be ascribed to polariton emission, which originates from the coupling interaction of the 1D photonic crystal and confined excitons along the wire direction. Using a p-type GaN layer as the hole transport layer, a kind of waveguide light source based on an individual ZnO/ZnO:Ga superlattice MW was proposed and constructed. By analysing the spatially resolved electroluminescence spectra, the observed multipeak was ascribed to exciton-polariton emission with a vacuum Rabi splitting of about 275 meV. Cladding with Rh nanostructures gives rise to appropriate ultraviolet plasmons, and the Rabi splitting energy of our device was enhanced up to 413 meV. The exciton-polariton properties were further examined using angle-resolved electroluminescence measurements. Therefore, individual superlattice MWs can act as optical microresonators to achieve photon-exciton coupling with a large Rabi splitting energy. The experimental results indicate that an individual ZnO/ZnO:Ga superlattice MW can be generally used in developing exciton-polariton luminescence/lasing light sources, particularly for constructing low-threshold/thresholdless lasers toward pragmatic applications.
Collapse
Affiliation(s)
- Haiying Xu
- College of Physics, MIIT Key Laboratory of Aerospace Information Materials and Physics, Key Laboratory for Intelligent Nano Materials and Devices, Nanjing University of Aeronautics and Astronautics, No. 29 Jiangjun Road, Nanjing 211106, China. .,College of Mathematics and Physics, Nanjing Institute of Technology, Nanjing, 211167, China
| | - Juan Xu
- College of Physics, MIIT Key Laboratory of Aerospace Information Materials and Physics, Key Laboratory for Intelligent Nano Materials and Devices, Nanjing University of Aeronautics and Astronautics, No. 29 Jiangjun Road, Nanjing 211106, China.
| | - Mingming Jiang
- College of Physics, MIIT Key Laboratory of Aerospace Information Materials and Physics, Key Laboratory for Intelligent Nano Materials and Devices, Nanjing University of Aeronautics and Astronautics, No. 29 Jiangjun Road, Nanjing 211106, China.
| | - Maosheng Liu
- College of Physics, MIIT Key Laboratory of Aerospace Information Materials and Physics, Key Laboratory for Intelligent Nano Materials and Devices, Nanjing University of Aeronautics and Astronautics, No. 29 Jiangjun Road, Nanjing 211106, China.
| | - Kai Tang
- College of Physics, MIIT Key Laboratory of Aerospace Information Materials and Physics, Key Laboratory for Intelligent Nano Materials and Devices, Nanjing University of Aeronautics and Astronautics, No. 29 Jiangjun Road, Nanjing 211106, China.
| | - Caixia Kan
- College of Physics, MIIT Key Laboratory of Aerospace Information Materials and Physics, Key Laboratory for Intelligent Nano Materials and Devices, Nanjing University of Aeronautics and Astronautics, No. 29 Jiangjun Road, Nanjing 211106, China.
| | - Daning Shi
- College of Physics, MIIT Key Laboratory of Aerospace Information Materials and Physics, Key Laboratory for Intelligent Nano Materials and Devices, Nanjing University of Aeronautics and Astronautics, No. 29 Jiangjun Road, Nanjing 211106, China.
| |
Collapse
|
3
|
Zhou X, Jiang M, Wu J, Liu M, Kan C, Shi D. Electrically driven whispering-gallery-mode microlasers in an n-MgO@ZnO:Ga microwire/p-GaN heterojunction. OPTICS EXPRESS 2022; 30:18273-18286. [PMID: 36221632 DOI: 10.1364/oe.457575] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 03/07/2022] [Accepted: 04/22/2022] [Indexed: 06/16/2023]
Abstract
In emerging miniaturized applications, semiconductor micro/nanostructures laser devices have drawn great public attentions of late years. The device performances of micro/nanostructured microlasers are highly restricted to the different reflective conditions at various side surfaces of microresonators and junction interface quality. In this study, an electrically driven whispering-gallery-mode (WGM) microlaser composed of a Ga-doped ZnO microwire covered by a MgO layer (MgO@ZnO:Ga MW) and a p-type GaN substrate is illustrated experimentally. Incorporating a MgO layer on the side surfaces of ZnO:Ga MWs can be used to reduce light leakage along the sharp edges and the ZnO:Ga/GaN interface. This buffer layer incorporation also enables engineering the energy band alignment of n-ZnO:Ga/p-GaN heterojunction and manipulating the current transport properties. The as-constructed n-MgO@ZnO:Ga MW/p-GaN heterojunction device can emit at an ultraviolet wavelength of 375.5 nm and a linewidth of about 25.5 nm, achieving the excitonic-related recombination in the ZnO:Ga MW. The broadband spectrum collapsed into a series of sharp peaks upon continuous-wave (CW) operation of electrical pumping, especially for operating current above 15.2 mA. The dominant emission line was centered at 378.5 nm, and the line width narrowed to approximately 0.95 nm. These sharp peaks emerged from the spontaneous emission spectrum and had an average spacing of approximately 5.5 nm, following the WGM cavity modes. The results highlight the significance of interfacial engineering for optimizing the performance of low-dimensional heterostructured devices and shed light on developing future miniaturized microlasers.
Collapse
|
4
|
Ma K, Li B, Zhou X, Jiang M, Liu Y, Kan C. Plasmon-enabled spectrally narrow ultraviolet luminescence device using Pt nanoparticles covered one microwire-based heterojunction. OPTICS EXPRESS 2021; 29:21783-21794. [PMID: 34265958 DOI: 10.1364/oe.431124] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 05/10/2021] [Accepted: 06/15/2021] [Indexed: 06/13/2023]
Abstract
Owing to great luminescent monochromaticity, high stability, and independent of automatic color filter, low dimensional ultraviolet light-emitting diodes (LEDs) via the hyperpure narrow band have attracted considerable interest for fabricating miniatured display equipments, solid state lighting sources, and other ultraviolet photoelectrical devices. In this study, a near-ultraviolet LED composed of one Ga-doped ZnO microwire (ZnO:Ga MW) and p-GaN layer was fabricated. The diode can exhibit bright electroluminescence (EL) peaking at 400.0 nm, with a line width of approximately 35 nm. Interestingly, by introducing platinum nanoparticles (PtNPs), we achieved an ultraviolet plasmonic response; an improved EL, including significantly enhanced light output; an observed blueshift of main EL peaks of 377.0 nm; and a reduction of line width narrowing to 10 nm. Working as a powerful scalpel, the decoration of PtNPs can be employed to tailor the spectral line profiles of the ultraviolet EL performances. Also, a rational physical model was built up, which could help us study the carrier transportation, recombination of electrons and holes, and dynamic procedure of luminescence. This method offers a simple and feasible way, without complicated fabricating technology such as an added insulating layer or core shell structure, to realize hyperpure ultraviolet LED. Therefore, the proposed engineering of energy band alignment by introducing PtNPs can be employed to build up high performance, high spectral purity luminescent devices in the short wavelengths.
Collapse
|
5
|
Ma K, Zhou X, Kan C, Xu J, Jiang M. Pt nanoparticles utilized as efficient ultraviolet plasmons for enhancing whispering gallery mode lasing of a ZnO microwire via Ga-incorporation. Phys Chem Chem Phys 2021; 23:6438-6447. [PMID: 33711087 DOI: 10.1039/d1cp00131k] [Citation(s) in RCA: 4] [Impact Index Per Article: 1.3] [Reference Citation Analysis] [Abstract] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/17/2022]
Abstract
Introducing nanostructured metals with ultraviolet plasmonic characters has attracted much attention for fabricating high performance optoelectronic devices in the shorter wavelength spectrum. In this work, platinum nanoparticles (PtNPs) with controlled plasmonic responses in ultraviolet wavelengths were successfully synthesized. To demonstrate the promising availability, PtNPs with desired sizes were deposited on a hexagonal ZnO microwire via Ga-doping (PtNPs@ZnO:Ga MW). Under ultraviolet illumination, typical near-band-edge emission of ZnO:Ga MW was considerably enhanced; meanwhile, the photocurrent is much larger than that of the bare MW. Thereby, the enhanced phenomena of a ZnO:Ga MW is related to localized surface plasmon resonances of the decorated PtNPs. A single MW with a hexagonal cross-section can be a potential platform to construct a whispering gallery mode (WGM) cavity due to its total inner wall reflection. Given this, the influence of PtNPs via ultraviolet plasmons on lasing features of the ZnO:Ga MW was tested. The lasing characteristics are significantly enhanced, including lasing output enhancement, a clear reduction of the threshold and the improvement of the quality factor. To exploit the working principle, PtNPs serving as powerful ultraviolet plasmons can couple with ZnO:Ga excitons, accelerating radiative recombination. Since fabricating stable, typical nanostructured metals with ultraviolet plasmons remains a challenging issue, the results illustrated in the work may offer a low-cost and efficient scheme for achieving plasmon-enhanced wide-bandgap semiconductor based ultraviolet optoelectronic devices with excellent performances.
Collapse
Affiliation(s)
- Kunjie Ma
- College of Science, MIIT Key Laboratory of Aerospace Information Materials and Physics, Key Laboratory for Intelligent Nano Materials and Devices, Nanjing University of Aeronautics and Astronautics, No. 29 Jiangjun Road, Nanjing 211106, China.
| | | | | | | | | |
Collapse
|
6
|
Kan C, Wu Y, Xu J, Wan P, Jiang M. Plasmon-enhanced strong exciton-polariton coupling in single microwire-based heterojunction light-emitting diodes. OPTICS EXPRESS 2021; 29:1023-1036. [PMID: 33726325 DOI: 10.1364/oe.414113] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.7] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 11/04/2020] [Accepted: 12/11/2020] [Indexed: 06/12/2023]
Abstract
Manipulating the strong light-matter coupling interaction in optical microresonators that are naturally formed by semiconductor micro- or nanostructures is crucial for fabricating high-performance exciton-polariton devices. Such devices can function as coherent light sources having considerably lower emission threshold. In this study, an exciton-polariton light-emitting diode (LED), made of a single ZnO microwire (MW) and a p-GaN substrate, serving as the hole injector, was fabricated, and its working characteristics, in the near-ultraviolet region, were demonstrated. To further improve the quality of the single ZnO MW-based optical microresonator, Ag nanowires (AgNWs) with ultraviolet plasmonic response were deposited on the MW. Apart from the improvement of the electrical and optical properties of the hexagonal ZnO MW, the optically pumped whispering-gallery-mode lasing characteristics were significantly enhanced. Furthermore, a single ZnO MW not covered, and covered by AgNWs, was used to construct a heterojunction LED. Compared with single bare ZnO MW-based LED, significant enhancement of the device performance was achieved, including a significant enhancement in the light output and a small emission band blueshift. Specifically, the exciton-polariton emission was observably enhanced, and the corresponding Rabi splitting energy (∼ 495 meV) was significantly higher than that of the bare ZnO MW-based LED (∼ 370 meV). That ultraviolet plasmons of AgNWs enhanced the exciton-polariton coupling strength was further confirmed via angle-resolved electroluminescence measurements of the single MW-based polaritonic devices, which clearly illustrated the presence of Rabi splitting and subband anti-crossing characteristics. The experimental results provide new avenues to achieve extremely high coupling strengths, which can accelerate the advancements in electrically driven high-efficiency polaritonic coherent emitters and nonlinear devices.
Collapse
|
7
|
Tang K, Jiang M, Wan P, Kan C. Continuous-wave operation of an electrically pumped single microribbon based Fabry-Perot microlaser. OPTICS EXPRESS 2021; 29:983-995. [PMID: 33726323 DOI: 10.1364/oe.412475] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 10/14/2020] [Accepted: 12/12/2020] [Indexed: 06/12/2023]
Abstract
Fabry-Perot (FP) mode microlasers have been popularized and applied widely in on-chip coherent light sources because of the unique advantages of directional output emission. In this work, a heterojunction light-emitting diode (LED) made of a Ga-doped ZnO (ZnO:Ga) microribbon and p-GaAs template is fabricated. And its electroluminescence characteristics of strong coupling of exciton-photon and polariton lasing, in the blue-violet spectrum, were demonstrated under continuous-wave operation of an electrical injection. In the device structure, a single microribbon with a rectangular-shaped cross section can achieve the FP-mode lasing action by the optical oscillation between the two lateral sides of the microcrystals in the ultraviolet spectrum. As the reverse-current is below the threshold value, the device can have radiative polaritonic lighting directly from bilateral sides of the microribbon, yielding strong coupling between excitons and FP-mode microresonator. And the exciton-polariton coupling strengths characterized by a Rabi splitting energy were extracted to be 500 meV. Further, when the input current increased more than a certain value, strong laser illuminating developed as two sharp peaks at the lower energy shoulder of the spontaneous emission peak, and these oscillating modes can dominate the waveguide EL spectra. The experimental results can provide us with further unambiguous evidence that the lasing is originated from the polariton resonances for the microribbon with strong exciton-polariton coupling. Since single microribbon based optical FP-mode microresonators do not require additional feedback mirrors, their compact size and resulting low thresholds make them a powerful candidate to construct on-chip coherent light sources for future integrated nanophotonic and optoelectronic circuitry.
Collapse
|