Plasmon-enhanced strong exciton-polariton coupling in single microwire-based heterojunction light-emitting diodes

Ultraviolet Exciton-Polariton Light-Emitting Diode in a ZnO Microwire Homojunction

Low-dimensional ZnO, possessing well-defined side facets and optical gain properties, has emerged as a promising material to develop ultraviolet coherent light sources. However, the realization of electrically driven ZnO homojunction luminescence and laser devices is still a challenge due to the absence of a reliable p-type ZnO. Herein, the sample of p-type ZnO microwires doped by Sb (ZnO:Sb MWs) was synthesized individually. Subsequently, the p-type conductivity was examined using a single-MW field-effect transistor. Upon optical pumping, a ZnO:Sb MW showing a regular hexagonal cross-section and smooth sidewall facets can feature as an optical microcavity, which is evidenced by the achievement of whispering-gallery-mode lasing. By combining an n-type ZnO layer, a single ZnO:Sb MW homojunction light-emitting diode (LED), which exhibited a typical ultraviolet emission at a wavelength of 379.0 nm and a line-width of approximately 23.5 nm, was constructed. We further illustrated that strong exciton-photon coupling can occur in the as-constructed p-ZnO:Sb MW/n-ZnO homojunction LED by researching spatially resolved electroluminescence spectra, contributing to the exciton-polariton effect. Particularly, varying the cross-sectional dimensions of ZnO:Sb wires can further modulate the exciton-photon coupling strengths. We anticipate that the results can provide an effective exemplification to realize reliable p-type ZnO and tremendously promote the development of low-dimensional ZnO homojunction optoelectronic devices.

Interface engineering enhanced near-infrared electroluminescence in an n-ZnO microwire/p-GaAs heterojunction

Interface engineering in the fabrication of low-dimensional optoelectronic devices has been highlighted in recent decades to enhance device characteristics such as reducing leakage current, optimizing charge transport, and modulating the energy-band structure. In this paper, we report a dielectric interface approach to realize one-dimensional (1D) wire near-infrared light-emitting devices with high brightness and enhanced emission efficiency. The light-emitting diode is composed of a zinc oxide microwire covered by a silver nanolayer (Ag@ZnO MW), magnesium oxide (MgO) buffer layer, and p-type gallium arsenide (GaAs) substrate. In the device structure, the insertion of a MgO dielectric layer in the n-ZnO MW/p-GaAs heterojunction can be used to modulate the device features, such as changing the charge transport properties, reducing the leakage current and engineering the band alignment. Furthermore, the cladding of the Ag nanolayer on the ZnO MW can optimize the junction interface quality, thus reducing the turn-on voltage and increasing the current injection and electroluminescence (EL) efficiency. The combination of MgO buffer layer and Ag nanolayer cladding can be utilized to achieve modulating the carrier recombination path, interfacial engineering of heterojunction with optimized band alignment and electronic structure in these carefully designed emission devices. Besides, the enhanced near-infrared EL and improved physical contact were also obtained. The study of current transport modulation and energy-band engineering proposes an original and efficient route for improving the device performances of 1D wire-type heterojunction light sources.

Electrically driven whispering-gallery-mode microlasers in an n-MgO@ZnO:Ga microwire/p-GaN heterojunction

In emerging miniaturized applications, semiconductor micro/nanostructures laser devices have drawn great public attentions of late years. The device performances of micro/nanostructured microlasers are highly restricted to the different reflective conditions at various side surfaces of microresonators and junction interface quality. In this study, an electrically driven whispering-gallery-mode (WGM) microlaser composed of a Ga-doped ZnO microwire covered by a MgO layer (MgO@ZnO:Ga MW) and a p-type GaN substrate is illustrated experimentally. Incorporating a MgO layer on the side surfaces of ZnO:Ga MWs can be used to reduce light leakage along the sharp edges and the ZnO:Ga/GaN interface. This buffer layer incorporation also enables engineering the energy band alignment of n-ZnO:Ga/p-GaN heterojunction and manipulating the current transport properties. The as-constructed n-MgO@ZnO:Ga MW/p-GaN heterojunction device can emit at an ultraviolet wavelength of 375.5 nm and a linewidth of about 25.5 nm, achieving the excitonic-related recombination in the ZnO:Ga MW. The broadband spectrum collapsed into a series of sharp peaks upon continuous-wave (CW) operation of electrical pumping, especially for operating current above 15.2 mA. The dominant emission line was centered at 378.5 nm, and the line width narrowed to approximately 0.95 nm. These sharp peaks emerged from the spontaneous emission spectrum and had an average spacing of approximately 5.5 nm, following the WGM cavity modes. The results highlight the significance of interfacial engineering for optimizing the performance of low-dimensional heterostructured devices and shed light on developing future miniaturized microlasers.

The Deformation Behavior and Bending Emissions of ZnO Microwire Affected by Deformation-Induced Defects and Thermal Tunneling Effect

The realization of electrically pumped emitters at micro and nanoscale, especially with flexibility or special shapes is still a goal for prospective fundamental research and application. Herein, zinc oxide (ZnO) microwires were produced to investigate the luminescent properties affected by stress. To exploit the initial stress, room temperature in situ elastic bending stress was applied on the microwires by squeezing between the two approaching electrodes. A novel unrecoverable deformation phenomenon was observed by applying a large enough voltage, resulting in the formation of additional defects at bent regions. The electrical characteristics of the microwire changed with the applied bending deformation due to the introduction of defects by stress. When the injection current exceeded certain values, bright emission was observed at bent regions, ZnO microwires showed illumination at the bent region priority to straight region. The bent emission can be attributed to the effect of thermal tunneling electroluminescence appeared primarily at bent regions. The physical mechanism of the observed thermoluminescence phenomena was analyzed using theoretical simulations. The realization of electrically induced deformation and the related bending emissions in single microwires shows the possibility to fabricate special-shaped light sources and offer a method to develop photoelectronic devices.

Plasmon-enabled spectrally narrow ultraviolet luminescence device using Pt nanoparticles covered one microwire-based heterojunction

Owing to great luminescent monochromaticity, high stability, and independent of automatic color filter, low dimensional ultraviolet light-emitting diodes (LEDs) via the hyperpure narrow band have attracted considerable interest for fabricating miniatured display equipments, solid state lighting sources, and other ultraviolet photoelectrical devices. In this study, a near-ultraviolet LED composed of one Ga-doped ZnO microwire (ZnO:Ga MW) and p-GaN layer was fabricated. The diode can exhibit bright electroluminescence (EL) peaking at 400.0 nm, with a line width of approximately 35 nm. Interestingly, by introducing platinum nanoparticles (PtNPs), we achieved an ultraviolet plasmonic response; an improved EL, including significantly enhanced light output; an observed blueshift of main EL peaks of 377.0 nm; and a reduction of line width narrowing to 10 nm. Working as a powerful scalpel, the decoration of PtNPs can be employed to tailor the spectral line profiles of the ultraviolet EL performances. Also, a rational physical model was built up, which could help us study the carrier transportation, recombination of electrons and holes, and dynamic procedure of luminescence. This method offers a simple and feasible way, without complicated fabricating technology such as an added insulating layer or core shell structure, to realize hyperpure ultraviolet LED. Therefore, the proposed engineering of energy band alignment by introducing PtNPs can be employed to build up high performance, high spectral purity luminescent devices in the short wavelengths.

Plasmon-enhanced strong exciton-polariton coupling in single microwire-based heterojunction light-emitting diodes: erratum

We provide a revised figure and the corrected related expressions of our previous publication [Opt. Express29(2), 1023(2021)10.1364/OE.414113].