Widely-tunable single-frequency diamond Raman laser

Multiphonon-coupling yellow laser in Yb:La2CaB10O19 crystal

Yellow lasers at 590 nm have many extensive applications in our daily life, but extremely difficult to attain by traditional solid-state laser technology, owing to the absence of highly-efficient transition channels at this spectral range. In this work, we proposed a cooperative lasing mechanism to obtain the yellow light emission, with multiphonon-assisted electronic transitions and phase-matched frequency-doubling. Based on the predictable configurational coordinate model, we can calculate the multiphonon-assisted emission step-by-step. Using Yb3+-doped La2CaB10O19 crystal as an example, it is capable of producing yellow laser at 581-590 nm, with a maximum output power of 4.83 W and a high slope efficiency of 31.6%. To the best of our knowledge, it represents the highest power of solid-state yellow laser realized in one single crystal pumped by a laser diode. This power scaling can be assigned to the amplified phonon-assisted emission beyond the fluorescence spectrum, and optimized crystal angle for phase-matching condition. Such a compact, low-cost, and high-power laser device, provides an alternative candidate for the spectral "yellow-gap" where no practical solid-state laser exists at present.

High power tunable Raman fiber laser at 1.2 μm waveband

Development of a high power fiber laser at special waveband, which is difficult to achieve by conventional rare-earth-doped fibers, is a significant challenge. One of the most common methods for achieving lasing at special wavelength is Raman conversion. Phosphorus-doped fiber (PDF), due to the phosphorus-related large frequency shift Raman peak at 40 THz, is a great choice for large frequency shift Raman conversion. Here, by adopting 150 m large mode area triple-clad PDF as Raman gain medium, and a novel wavelength-selective feedback mechanism to suppress the silica-related Raman emission, we build a high power cladding-pumped Raman fiber laser at 1.2 μm waveband. A Raman signal with power up to 735.8 W at 1252.7 nm is obtained. To the best of our knowledge, this is the highest output power ever reported for fiber lasers at 1.2 μm waveband. Moreover, by tuning the wavelength of the pump source, a tunable Raman output of more than 450 W over a wavelength range of 1240.6-1252.7 nm is demonstrated. This work proves PDF's advantage in high power large frequency shift Raman conversion with a cladding pump scheme, thus providing a good solution for a high power laser source at special waveband.

Secondary Raman and Brillouin mode suppression in two- and three-mirror-cavity diamond Raman lasers

We report an investigation into secondary mode suppression in single longitudinal mode (SLM) 1240 nm diamond Raman lasers. For a three-mirror V-shape standing-wave cavity incorporating an intra-cavity LBO crystal to suppress secondary modes, we achieved stable SLM output with a maximum output power of 11.7 W and a slope efficiency 34.9%. We quantify the level of χ⁽²⁾ coupling necessary to suppress secondary modes including those generated by stimulated Brillouin scattering (SBS). It is found that SBS-generated modes often coincide with higher-order spatial modes in the beam profile and can be suppressed using an intracavity aperture. Using numerical calculations, it is shown that the probability for such higher-order spatial modes is higher for an apertureless V-cavity than in two-mirror cavities due its contrasting longitudinal mode-structure.

Realization of CW single-frequency tunable Ti:sapphire laser with immunity to the noise of the pump source

All-solid-state continuous-wave (CW) single-frequency tunable Ti:sapphire (Ti:S) laser is an important source in quantum optics and atomic physics. However, intracavity etalon (IE) locking is easily influenced by the intensity noise of the pump source in the low frequency band. In order to address this issue, a differential detector with dual-photodiodes (PDs) is designed and employed in the experiment. Both PDs are used to detect the lights of the pump source and the built Ti:S laser, respectively. As a result, the influence of the intensity noise of the pump source on the stability of the IE locking is successfully eliminated and the IE is stably locked to the oscillating longitudinal-mode of the laser. On this basis, a stable CW single-frequency tunable Ti:S laser is realized. The presented method is beneficial to attain a stable single-frequency tunable laser with immunity to the intensity noise of the pump source.

Modulation depth and bandwidth analysis of planar thermo-optic diamond actuators

Thermo-optic actuators based on bulk materials are considered too slow in applications such as laser frequency control. The availability of high-quality optical materials that have extremely fast thermal response times, such as diamond, present an opportunity for increasing performance. Here, diamond thermal actuators are investigated for configurations that use a planar thermal resistive layer applied to a heat-sinked rectangular prism. A general analytical formulation is obtained which simplifies substantially for high thermal conductivity such as diamond. Expressions for modulation depth, bandwidth and power requirements are obtained as functions of modulator dimensions and heat-transfer coefficients. For a 1 mm × 1 mm cross-section diamond at wavelength of 1 μm, around 450 W of applied heat power is needed to achieve a π phase shift at a modulation frequency of 2 kHz.

A Review of the High-Power All-Solid-State Single-Frequency Continuous-Wave Laser

High-power all-solid-state single-frequency continuous-wave (CW) lasers have been applied in basic research such as atomic physics, precision measurement, radar and laser guidance, as well as defense and military fields owing to their intrinsic advantages of high beam quality, low noise, narrow linewidth, and high coherence. With the rapid developments of sciences and technologies, the traditional single-frequency lasers cannot meet the development needs of emerging science and technology such as quantum technology, quantum measurement and quantum optics. After long-term efforts and technical research, a novel theory and technology was proposed and developed for improving the whole performance of high-power all-solid-state single-frequency CW lasers, which was implemented by actively introducing a nonlinear optical loss and controlling the stimulated emission rate (SER) in the laser resonator. As a result, the output power, power and frequency stabilities, tuning range and intensity noise of the single-frequency lasers were effectively enhanced.