Wavelength-switchable ultra-narrow linewidth fiber laser enabled by a figure-8 compound-ring-cavity filter and a polarization-managed four-channel filter

Near thermal noise limit, 5W single frequency fiber laser base on the ring cavity configuration

In this study, we present an ultralow noise single-frequency fiber laser operating at 1550 nm, utilizing a traveling-wave ring cavity configuration. The frequency noise of the laser approaches the thermal noise limit, achieving a white noise level of 0.025 Hz2/Hz, resulting in an instantaneous linewidth of 0.08 Hz. After amplification, the output power reaches 4.94 W while maintaining the same low white noise level as the laser oscillator. The integration linewidths of the laser oscillator and amplifier are 221 Hz and 665 Hz, respectively, with both exhibiting relative intensity noises that approach the quantum shot noise limit. To the best of our knowledge, this work shows the lowest frequency noise combined with relatively high power for this type of ring cavity fiber laser.

2 µm band four-wavelength-switchable narrow linewidth fiber laser enabled by fs-laser direct-written polarization-dependent parallel fiber Bragg gratings

We propose and experimentally demonstrate a four-wavelength-switchable single-longitudinal-mode (SLM) narrow linewidth thulium-holmium co-doped fiber laser (THDFL) using two polarization-dependent parallel fiber Bragg gratings (PD-PFBGs). The PD-PFBGs, fabricated using femtosecond (fs) laser direct-writing technology in a standard single-mode fiber (SMF) via a point-by-point method, are used as a four-channel reflection filter. Two FBGs are inscribed in parallel in the fiber core along the axial direction and are uniquely positioned symmetrically on either side of the centerline. This configuration enables polarization-dependent multi-channel filtering capability, which further allows for polarization-control-based four-wavelength-switchable operations of the THDFL. SLM lasing is accomplished by utilizing a simple dual-ring sub-cavity filter. An exceptional output performance of the THDFL is achieved, including an optical signal-to-noise ratio (SNR) of >72 dB, maximum power and wavelength fluctuations of 0.350 dB and 0.024 nm, respectively, and a linewidth of <2 kHz, for all four single-wavelength operations lasing at ∼2000 nm. These performance indicators suggest that the THDFL can be applied in free-space optical communication, atmospheric monitoring, and Lidar.

Effective linewidth compression of a single-longitudinal-mode fiber laser with randomly distributed high scattering centers in the fiber induced by femtosecond laser pulses

Femtosecond lasers can be used to create many functional devices in silica optical fibers with high designability. In this work, a femtosecond laser-induced high scattering fiber (HSF) with randomly distributed high scattering centers is used to effectively compress the linewidth of a fiber laser for the first time. A dual-wavelength, single-longitudinal-mode (SLM) erbium-doped fiber laser (EDFL) is constructed for the demonstration, which is capable of switching among two single-wavelength operations and one dual-wavelength operation. We find that the delayed self-heterodyne beating linewidth of the laser can be reduced from >1 kHz to <150 Hz when the length of the HSF in the laser cavity increases from 0 m to 20 m. We also find that the intrinsic Lorentzian linewidth of the laser can be compressed to several Hz using the HSF. The efficiency and effectiveness of linewidth reduction are also validated for the case that the laser operates in simultaneous dual-wavelength lasing mode. In addition to the linewidth compression, the EDFL shows outstanding overall performance after the HSF is incorporated. In particular, the optical spectrum and SLM lasing state are stable over long periods of time. The relative intensity noise is as low as <-150 dB/Hz@>3 MHz, which is very close to the shot noise limit. The optical signal-to-noise ratios of >85 dB for single-wavelength operation and >83 dB for dual-wavelength operation are unprecedented over numerous SLM fiber lasers reported previously. This novel method for laser linewidth reduction is applicable across gain-medium-type fiber lasers, which enables low-cost, high-performance, ultra-narrow linewidth fiber laser sources for many applications.

Fiber Bragg grating-based linear-cavity fiber laser

A fiber Bragg grating-based linear-cavity fiber laser is proposed and demonstrated experimentally. A single-mode fiber Bragg grating is used as a wavelength selector in the fundamental mode, and four few-mode fiber Bragg gratings are used to reflect LP₀₁ mode, LP₁₁ mode, LP₂₁ mode and LP₀₂ mode at the same wavelength. Different modes can be reflected at the same wavelength between a single-mode fiber Bragg grating and four few-mode fiber Bragg gratings to form four sub-linear-cavities. This fiber laser, which enables simultaneous lasing of LP₀₁ mode, LP₁₁ mode, LP₂₁ mode and LP₀₂ mode at the same wavelength, plays an important role in the field of mode-division multiplexing fiber-optic communications.