Interferometric temperature-insensitive strain measurement with different-diameter fiber Bragg gratings

Optical Fibre-Based Sensors for Oil and Gas Applications

Oil and gas (O&G) explorations moving into deeper zones for enhanced oil and gas recovery are causing serious safety concerns across the world. The sensing of critical multiple parameters like high pressure, high temperature (HPHT), chemicals, etc., are required at longer distances in real-time. Traditional electrical sensors operate less effectively under these extreme environmental conditions and are susceptible to electromagnetic interference (EMI). Hence, there is a growing demand for improved sensors with enhanced measurement capabilities and also sensors that generates reliable data for enhanced oil and gas production. In addition to enhanced oil and gas recovery, the sensing technology should also be capable of monitoring the well bore integrity and safety. The sensing requirements of the O&G industry for improved sensing in deeper zones include increased transmission length, improved spatial coverage and integration of multiple sensors with multimodal sensing capability. This imposes problems like signal attenuation, crosstalks and cross sensitivities. Optical fibre-based sensors are expected to provide superior sensing capabilities compared to electrical sensors. This review paper covers a detailed review of different fibre-optic sensing technologies to identify a feasible sensing solution for the O&G industry.

A Composite Fabry-Perot Interferometric Sensor with the Dual-Cavity Structure for Simultaneous Measurement of High Temperature and Strain

In this paper, an optical fiber composite Fabry-Perot interferometric (CFPI) sensor capable of simultaneous measurement of high temperature and strain is presented. The CFPI sensor consists of a silica-cavity intrinsic Fabry-Perot interferometer (IFPI) cascading an air-cavity extrinsic Fabry-Perot interferometer (EFPI). The IFPI is constructed at the end of the transmission single-mode fiber (SMF) by splicing a short piece of photonic crystal fiber (PCF) to SMF and then the IFPI is inserted into a quartz capillary with a reflective surface to form a single-ended sliding EFPI. In such a configuration, the IFPI is only sensitive to temperature and the EFPI is sensitive to strain, which allows the achieving of temperature-compensated strain measurement. The experimental results show that the proposed sensor has good high-temperature resistance up to 1000 °C. Strain measurement under high temperatures is demonstrated for high-temperature suitability and stable strain response. Featuring intrinsic safety, compact structure and small size, the proposed CFPI sensor may find important applications in the high-temperature harsh environment.

Enhanced strain and temperature sensing by reduced graphene oxide coated etched fiber Bragg gratings

This Letter reports on an etched fiber Bragg grating (eFBG) sensor coated with reduced graphene oxide (RGO) having enhanced sensitivity for physical parameters such as strain and temperature. The synergetic effect of the changes in grating pitch and refractive index of RGO with change in temperature or strain enhances the shift in Bragg wavelength (λ_B). The RGO-coated eFBG sensors exhibit a strain sensitivity of 5.5 pm/μϵ (∼5 times that of bare fiber Bragg gratings) and temperature sensitivity of 33 pm/°C (∼3 times that of bare fiber Bragg gratings). The resolutions of ∼1  μϵ and ∼0.3°C have been obtained for strain and temperature respectively, using RGO-coated eFBG sensors.

Optical Fiber Sensors for Aircraft Structural Health Monitoring

Aircraft structures require periodic and scheduled inspection and maintenance operations due to their special operating conditions and the principles of design employed to develop them. Therefore, structural health monitoring has a great potential to reduce the costs related to these operations. Optical fiber sensors applied to the monitoring of aircraft structures provide some advantages over traditional sensors. Several practical applications for structures and engines we have been working on are reported in this article. Fiber Bragg gratings have been analyzed in detail, because they have proved to constitute the most promising technology in this field, and two different alternatives for strain measurements are also described. With regard to engine condition evaluation, we present some results obtained with a reflected intensity-modulated optical fiber sensor for tip clearance and tip timing measurements in a turbine assembled in a wind tunnel.

Multiwavelength Raman-fiber-laser-based long-distance remote sensor for simultaneous measurement of strain and temperature

We propose a simple and flexible multiwavelength Raman-fiber-laser-based long-distance remote-sensing scheme for simultaneous measurement of strain and temperature by use of fiber Bragg gratings. By combining two uniform fiber Bragg gratings with a tunable chirped fiber grating, we readily achieve simultaneous two-channel sensing probes with a high extinction ratio of more than approximately 50 dB over a 50-km distance. When strain and temperature are applied, lasing wavelength separation and shift occur, respectively, since the two uniform fiber Bragg gratings have identical material composition and different cladding diameters. This allows simultaneous measurement of strain and temperature for long-distance sensing applications of more than 50 km.

Transfer-matrix approach based on modal analysis for modeling corrugated long-period fiber gratings

A transfer-matrix method is developed for modeling a corrugated long-period fiber grating. Cladding-mode resonance in such a corrugated structure can be controlled by the applied tensile stress based on the photoelastic effect. A first-order vectorial perturbation expansion is used to derive the mode fields of the two basic regions under the strain-induced index perturbation. Because the etched cladding radius is much smaller than the unetched radius, the effect of the corrugated structure on cladding modes cannot be treated as a small perturbation. Thus the conventional coupled-mode theory is inadequate for the modeling of such a structure. Based on a self-consistent mode-matching technique, mode coupling within the corrugated structure can be described by a set of transfer matrices. We apply the formulation to the calculation of the transmission spectra of a corrugated long-period grating and compare the calculated with the experimental results. The transfer-matrix approach is found to account well for the features of the transmission spectra of the corrugated long-period gratings.

Dynamic-strain measurement with dual-grating fiber sensor

A dual-grating sensor head, which was designed for temperature-insensitive strain measurement, was used to measure fast-varying strain perturbations. Using a Mach-Zehnder interferometer technique, we obtained ~0.1-muepsilon (microstrain) rms resolution with a 200-Hz strain input. The feasibility of measuring a dynamic-strain with a static-strain measuring configuration was also demonstrated.