1
|
Lalam N, Bhatta H, Sun X, Lu P, Ohodnicki P, Buric MP, Wright R. Multi-parameter distributed fiber optic sensing using double-Brillouin peak fiber in Brillouin optical time domain analysis. OPTICS EXPRESS 2023; 31:36590-36602. [PMID: 38017807 DOI: 10.1364/oe.498141] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 06/27/2023] [Accepted: 09/28/2023] [Indexed: 11/30/2023]
Abstract
In this paper, we demonstrate a multi-parameter fiber sensing system based on stimulated Brillouin scattering in a double-Brillouin peak specialty fiber with enhanced Brillouin gain response. The amplitude level of the second Brillouin gain peak, which originated from the higher-order acoustic modes, has been improved with an approximately similar amplitude level to the first Brillouin gain peak from the fundamental acoustic mode. Compared to other multi-Brillouin peak fibers presented in the literature, the proposed fiber significantly reduces the measured Brillouin frequency shift error, thus improving strain and temperature accuracies. By utilizing the sensitivity values of the strain and temperature associated with each Brillouin gain spectrum (BGS) peak, a successful discriminative measurement of strain and temperature is performed with an accuracy of ±13 μɛ, and ±0.5 °C, respectively. The proposed double-Brillouin peak fiber appears to be a possible alternative to other multi-BGS peak fibers, for instance, large effective area fiber and dispersion compensating fibers, which are inherently accompanied by large measurement errors due to the weak Brillouin gain values originating from the higher-order acoustic modes. The demonstrated results show different strain and temperature coefficients of 47 kHz/µɛ, 1.15 MHz/°C for peak 1 and 51 kHz/µɛ, 1.37 MHz/°C for peak 2. Moreover, the enhanced BGS peak gains having nearly the same amplitude levels enable the discriminative measurement of strain and temperature. Such fibers in Brillouin interrogation eliminate the need for complex monitoring setups and reduce measurement errors. We recommend that for long-distance natural gas pipeline monitoring, where discriminative strain and temperature measurement is crucial, the proposed double-Brillouin peak fiber can be highly beneficial.
Collapse
|
2
|
Zhang Z, You G, Qin Y, Peng J, Xie S, Jiang X, Wang C, Yu R, Shen Y, Xiao L. Fabrication and Characterization of an Optimized Low-Loss Two-Mode Fiber for Optoacoustic Sensing. MICROMACHINES 2022; 13:1774. [PMID: 36296127 PMCID: PMC9611410 DOI: 10.3390/mi13101774] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Figures] [Subscribe] [Scholar Register] [Received: 09/20/2022] [Revised: 10/08/2022] [Accepted: 10/15/2022] [Indexed: 06/16/2023]
Abstract
An optimized multi-step index (MSI) 2-LP-mode fiber is proposed and fabricated with low propagation loss of 0.179 dB/km, low intermodal crosstalk and excellent bend resistance. We experimentally clarified the characteristics of backward Brillouin scattering (BBS) and forward Brillouin scattering (FBS) induced by radial acoustic modes (R0,m) in the fabricated MSI 2-LP-mode fiber, respectively. Via the use of this two-mode fiber, we demonstrated a novel discriminative measurement method of temperature and acoustic impedance based on BBS and FBS, achieving improved experimental measurement uncertainties of 0.2 °C and 0.019 kg/(s·mm2) for optoacoustic chemical sensing. The low propagation loss of the sensing fiber and the new measurement method based on both BBS and FBS may pave the way for long-distance and high spatial resolution distributed fiber sensors.
Collapse
Affiliation(s)
- Zelin Zhang
- Zhongtian Technology Advanced Materials Co., Ltd., Zhongtian Technology Group, Nantong 226010, China
- Advanced Fiber Devices and Systems Group, Key Laboratory of Micro and Nano Photonic Structures (MoE), Key Laboratory for Information Science of Electromagnetic Waves (MoE), Shanghai Engineering Research Center of Ultra-Precision Optical Manufacturing, School of Information Science and Technology, Fudan University, Shanghai 200433, China
| | - Guanglei You
- Zhongtian Technology Fiber Co., Ltd., Zhongtian Technology Group, Nantong 226010, China
| | - Yu Qin
- Zhongtian Technology Advanced Materials Co., Ltd., Zhongtian Technology Group, Nantong 226010, China
- Advanced Fiber Devices and Systems Group, Key Laboratory of Micro and Nano Photonic Structures (MoE), Key Laboratory for Information Science of Electromagnetic Waves (MoE), Shanghai Engineering Research Center of Ultra-Precision Optical Manufacturing, School of Information Science and Technology, Fudan University, Shanghai 200433, China
| | - Jianqin Peng
- College of Physics, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
| | - Shuhong Xie
- Zhongtian Technology Group, Nantong 226463, China
| | - Xinli Jiang
- Zhongtian Technology Group, Nantong 226463, China
| | - Caoyuan Wang
- Advanced Fiber Devices and Systems Group, Key Laboratory of Micro and Nano Photonic Structures (MoE), Key Laboratory for Information Science of Electromagnetic Waves (MoE), Shanghai Engineering Research Center of Ultra-Precision Optical Manufacturing, School of Information Science and Technology, Fudan University, Shanghai 200433, China
| | - Ruowei Yu
- Advanced Fiber Devices and Systems Group, Key Laboratory of Micro and Nano Photonic Structures (MoE), Key Laboratory for Information Science of Electromagnetic Waves (MoE), Shanghai Engineering Research Center of Ultra-Precision Optical Manufacturing, School of Information Science and Technology, Fudan University, Shanghai 200433, China
| | - Yichun Shen
- Zhongtian Technology Advanced Materials Co., Ltd., Zhongtian Technology Group, Nantong 226010, China
| | - Limin Xiao
- Advanced Fiber Devices and Systems Group, Key Laboratory of Micro and Nano Photonic Structures (MoE), Key Laboratory for Information Science of Electromagnetic Waves (MoE), Shanghai Engineering Research Center of Ultra-Precision Optical Manufacturing, School of Information Science and Technology, Fudan University, Shanghai 200433, China
| |
Collapse
|
3
|
Rjeb A, Ragheb AM, Esmail MA, Fathallah H, Alshebeili SA. Discriminative strain and temperature sensing using a ring-hyperbolic tangent fiber sensor. OPTICS EXPRESS 2022; 30:34612-34628. [PMID: 36242470 DOI: 10.1364/oe.471647] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 07/27/2022] [Accepted: 08/26/2022] [Indexed: 06/16/2023]
Abstract
Brillouin fiber sensors have demonstrated strong capability in discriminative and high-sensitivity multiparameter measurements. In this study, we proposed and numerically investigated novel ring core fiber-based stimulated Brillouin scattering for the simultaneous measurement of temperature and strain. The novel fiber, referred to as ring hyperbolic tangent (R-HTAN) fiber, is characterized by a shape parameter (α) that controls the optical refractive index and longitudinal acoustic velocity profiles. Numerical modal simulations indicated that the Brillouin gain spectrum contained multiple widely spaced and high-gain peaks, which were attributed to the strong interaction between the optical linearly polarized mode (i.e., LP0,1 as a pump wave) and multiple high-order longitudinal acoustic modes. The designed R-HTAN fiber enabled the discriminative sensing of temperature and strain with levels that clearly surpassed values recently reported in the literature. In case of straight R-HTAN fiber (α = 0), the maximum C(α=0)T and C(α=0)ε are 1.928 MHz/ ∘C and 0.087 MHz, respectively. In case of graded R-HTAN fiber (α = 1), the maximum C(α=1)T and C(α=1)ε are 1.872 MHz/ ∘C and 0.0842 MHz/μɛ, respectively. The errors associated with temperature measurements (maximum δT(α=0) = 0.0846 ∘C and maximum δT(α=1) = 7.4184 ∘C) and strain measurements (maximum δɛ(α=0) = 0.7250 μɛ and maximum δɛ(α=1) = 7.4184 μɛ) demonstrated that the proposed fiber could be a promising candidate for next-generation Brillouin sensing systems for enabling temperature and strain discrimination.
Collapse
|
4
|
Greenberg AP, Ma Z, Ramachandran S. Angular momentum driven dynamics of stimulated Brillouin scattering in multimode fibers. OPTICS EXPRESS 2022; 30:29708-29721. [PMID: 36299139 DOI: 10.1364/oe.462677] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 05/05/2022] [Accepted: 07/04/2022] [Indexed: 06/16/2023]
Abstract
The strength of stimulated Brillouin scattering (SBS) in optical fibers is largely governed by the spatial overlap between supported optical and acoustic modes, leading to a complicated amalgamation of photon-phonon interactions in multimode fibers. Here, we study SBS dynamics in ring-core fibers that support modes carrying orbital angular momentum (OAM), which result in distinctive characteristics. We find that the OAM SBS response, as well as modal content, strongly depends on the polarization state of the pump, as OAM modes in fiber have distinct propagation dynamics depending on whether the input is circularly or linearly polarized. This is in contrast to conventionally posited wisdom that SBS strength is independent of the pump's input polarization state in an isotropic material. This increased specificity can lead to interesting effects such as spatial phase conjugation even in the presence of stably transmitted, i.e. non-aberrated, spatial pump modes. More generally, we show that using OAM modes yields additional degrees of control over SBS interactions beyond more conventional parameters, such as effective area, acousto-optic spatial overlaps, and material composition.
Collapse
|
5
|
Intramode Brillouin Scattering Properties of Single-Crystal Lithium Niobate Optical Fiber. APPLIED SCIENCES-BASEL 2022. [DOI: 10.3390/app12136476] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 02/04/2023]
Abstract
Ordinary step-type fiber usually has only one obvious Brillouin scattering gain peak with a low gain coefficient, resulting in a poor sensing performance. As a promising material for nonlinear photonics, lithium niobate can significantly improve the Brillouin gain due to its higher refractive index when replaced with the core material. Furthermore, the higher-order acoustic modes make the Brillouin gain spectrum exhibit multiple scattering peaks, which could improve the performance of sensors. In this study, we simulated the Brillouin scattering properties of different modes of intramode in step-index lithium niobate core fibers. We analyzed the intramode-stimulated Brillouin scattering properties of different pump–Stokes pairs for nine LP modes (LP01, LP11, LP21, LP02, LP31, LP12, LP41, LP22, and LP03) guided in fiber. The results show that both the effective refractive index and Brillouin scattering frequency shift are decreased with the increase in the nine mode orders, and the values of which are 2.2413 to 2.1963, and 21.17 to 20.73 GHz, respectively. The typical back-stimulated Brillouin scattering gain is obtained at 1.7525 m−1·W−1. These simulation results prove that the Brillouin gain of the LiNbO3 optical fiber structure can be significantly improved, which will pave the way for better distributed Brillouin sensing and for improving the transmission capacity of communication systems.
Collapse
|
6
|
Bao X, Zhou Z, Wang Y. Review: distributed time-domain sensors based on Brillouin scattering and FWM enhanced SBS for temperature, strain and acoustic wave detection. PHOTONIX 2021; 2:14. [PMID: 34841256 PMCID: PMC8610014 DOI: 10.1186/s43074-021-00038-w] [Citation(s) in RCA: 10] [Impact Index Per Article: 3.3] [Reference Citation Analysis] [Abstract] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 05/24/2021] [Accepted: 07/15/2021] [Indexed: 06/02/2023]
Abstract
Distributed time-domain Brillouin scattering fiber sensors have been widely used to measure the changes of the temperature and strain. The linear dependence of the temperature and strain on the Brillouin frequency shift enabled the distributed temperature and strain sensing based on mapping of the Brillouin gain spectrum. In addition, an acoustic wave can be detected by the four wave mixing (FWM) associated SBS process, in which phase matching condition is satisfied via up-down conversion of SBS process through birefringence matching before and after the conversion process. Brillouin scattering can be considered as the scattering of a pump wave from a moving grating (acoustic phonon) which induces a Doppler frequency shift in the resulting Stokes wave. The frequency shift is dependent on many factors including the velocity of sound in the scattering medium as well as the index of refraction. Such a process can be used to monitor the gain of random fiber laser based on SBS, the distributed acoustic wave reflect the distributed SBS gain for random lasing radiation, as well as the relative intensity noise inside the laser gain medium. In this review paper, the distributed time-domain sensing system based on Brillouin scattering including Brillouin optical time-domain reflectometry (BOTDR), Brillouin optical time-domain analysis (BOTDA), and FWM enhanced SBS for acoustic wave detection are introduced for their working principles and recent progress. The distributed Brillouin sensors based on specialty fibers for simultaneous temperature and strain measurement are summarized. Applications for the Brillouin scattering time-domain sensors are briefly discussed.
Collapse
Affiliation(s)
- Xiaoyi Bao
- School of Electrical Engineering and Computer Science, University of Ottawa, Ottawa, Ontario K1N 6N5 Canada
- Department of Physics, University of Ottawa, 25 Templeton Street, Ottawa, Ontario K1N 6N5 Canada
| | - Zichao Zhou
- Department of Physics, University of Ottawa, 25 Templeton Street, Ottawa, Ontario K1N 6N5 Canada
| | - Yuan Wang
- School of Electrical Engineering and Computer Science, University of Ottawa, Ottawa, Ontario K1N 6N5 Canada
| |
Collapse
|
7
|
Wang H, Gao S, Baker C, Wang Y, Chen L, Bao X. Stimulated Brillouin scattering in a tapered dual-core As 2Se 3-PMMA fiber for simultaneous temperature and strain sensing. OPTICS LETTERS 2020; 45:3301-3304. [PMID: 32538968 DOI: 10.1364/ol.391734] [Citation(s) in RCA: 3] [Impact Index Per Article: 0.8] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 03/09/2020] [Accepted: 05/12/2020] [Indexed: 06/11/2023]
Abstract
Chalcogenide fibers are currently being used widely in nonlinear optical signal processing, as they exhibit ultrahigh nonlinearity. Here, we propose a sensor based on stimulated Brillouin scattering for simultaneous temperature and strain measurement in a dual-core tapered As2Se3-polymethyl methacrylate fiber using a Brillouin optical time-domain analysis system. Different Brillouin frequency responses under temperature and strain variations and the separation of Brillouin frequency shifts (BFSs) in two principal polarization axes are demonstrated experimentally over a 50-cm-long tapered dual-core hybrid microfiber. The temperature coefficients are -3.8272MHz/∘C and -3.3302MHz/∘C, and the strain coefficients are -0.06143MHz/µε and -0.03463MHz/µε. Due to the different temperature and strain dependences of Brillouin frequency peaks in two polarizations, temperature and strain resolutions of 1°C and 33µε are realized, respectively. Numerical simulations are also reported to account for the BFS difference in two polarization axes.
Collapse
|
8
|
Zhang Z, Lu Y, Pan Y, Bao X, Chen L. Trench-assisted multimode fiber used in Brillouin optical time domain sensors. OPTICS EXPRESS 2019; 27:11396-11405. [PMID: 31052984 DOI: 10.1364/oe.27.011396] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.2] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 01/22/2019] [Accepted: 03/30/2019] [Indexed: 06/09/2023]
Abstract
The trench-assisted multimode fiber TA-OM4 is used as a sensing fiber to achieve a higher signal-to-noise (SNR) in Brillouin optical time domain sensors, due to its high stimulated Brillouin threshold and high modulation instability threshold. The Brillouin gain spectrum (BGS), stimulated Brillouin scattering (SBS) and modulation instability (MI) thresholds of TA-OM4 at 1550 nm are characterized and demonstrated theoretically and experimentally. The SNR improvements of TA-OM4 over G655 and G657 at the end of 15.5 km-long fibers, which are respectively 1.1 dB and 2.3 dB are verified experimentally. We achieve a temperature uncertainty of 0.3°C in 15.5 km TA-OM4 with 5 m spatial resolution by use of a Brillouin optical time domain reflectometry (BOTDR) sensor. The good bend resistance and high SBS and MI thresholds of TA-OM4 with better SNR improvements over SMFs works at the extreme bending conditions.
Collapse
|
9
|
Fang J, Milione G, Stone J, Peng G, Li MJ, Ip E, Li Y, Ji PN, Huang YK, Huang MF, Murakami S, Shieh W, Wang T. Multi-parameter distributed fiber sensing with higher-order optical and acoustic modes. OPTICS LETTERS 2019; 44:1096-1099. [PMID: 30821779 DOI: 10.1364/ol.44.001096] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.4] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 10/23/2018] [Accepted: 01/25/2019] [Indexed: 06/09/2023]
Abstract
We propose a novel multi-parameter sensing technique based on a Brillouin optical time domain reflectometry in the elliptical-core few-mode fiber, using higher-order optical and acoustic modes. Multiple Brillouin peaks are observed for the backscattering of both the LP01 mode and LP11 mode. We characterize the temperature and strain coefficients for various optical-acoustic mode pairs. By selecting the proper combination of modes pairs, the performance of multi-parameter sensing can be optimized. Distributed sensing of temperature and strain is demonstrated over a 0.5-km elliptical-core few-mode fiber, with the discriminative uncertainty of 0.28°C and 5.81 με for temperature and strain, respectively.
Collapse
|
10
|
Recent Advances in Brillouin Optical Correlation-Domain Reflectometry. APPLIED SCIENCES-BASEL 2018. [DOI: 10.3390/app8101845] [Citation(s) in RCA: 8] [Impact Index Per Article: 1.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/16/2022]
Abstract
Distributed fiber-optic sensing based on Brillouin scattering has been extensively studied and many configurations have been developed so far. In this paper, we review the recent advances in Brillouin optical correlation-domain reflectometry (BOCDR), which is known as a unique technique with intrinsic single-end accessibility, high spatial resolution, and cost efficiency. We briefly discuss the advantages and disadvantages of BOCDR over other Brillouin-based distributed sensing techniques, and present the fundamental principle and properties of BOCDR with some special schemes for enhancing the performance. We also describe the recent development of a high-speed configuration of BOCDR (slope-assisted BOCDR), which offers a beyond-nominal-resolution detectability. The paper is summarized with some future prospects.
Collapse
|
11
|
Discrimination of Temperature and Strain in Brillouin Optical Time Domain Analysis Using a Multicore Optical Fiber. SENSORS 2018; 18:s18041176. [PMID: 29649148 PMCID: PMC5948480 DOI: 10.3390/s18041176] [Citation(s) in RCA: 14] [Impact Index Per Article: 2.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 03/06/2018] [Revised: 04/06/2018] [Accepted: 04/09/2018] [Indexed: 11/17/2022]
Abstract
Brillouin optical time domain analysis is the sensing of temperature and strain changes along an optical fiber by measuring the frequency shift changes of Brillouin backscattering. Because frequency shift changes are a linear combination of temperature and strain changes, their discrimination is a challenge. Here, a multicore optical fiber that has two cores is fabricated. The differences between the cores' temperature and strain coefficients are such that temperature (strain) changes can be discriminated with error amplification factors of 4.57 °C/MHz (69.11 μ ϵ /MHz), which is 2.63 (3.67) times lower than previously demonstrated. As proof of principle, using the multicore optical fiber and a commercial Brillouin optical time domain analyzer, the temperature (strain) changes of a thermally expanding metal cylinder are discriminated with an error of 0.24% (3.7%).
Collapse
|
12
|
Abstract
In this work, we demonstrate the measurement of the Brillouin gain spectra of vector modes in a few-mode fiber for the first time using a simple heterodyne detection technique. A tunable long period fiber grating is used to selectively excite the vector modes supported by the few-mode fiber. Further, we demonstrate the non-destructive measurement of the absolute effective refractive indices (neff) of vector modes with ~10−4 accuracy based on the acquired Brillouin frequency shifts of the modes. The proposed technique represents a new tool for probing and controlling vector modes as well as modes carrying orbital angular momentum in optical fibers with potential applications in advanced optical communications and multi-parameter fiber-optic sensing.
Collapse
|