Optimized optical coupling to silica-clad photonic crystal waveguides

OFDR analysis of Si photonics FMCW LiDAR chip

We experimentally analyzed the internal reflection and loss of each component in a Si photonics frequency-modulated continuous-wave light detection and ranging (FMCW LiDAR) device using optical frequency domain reflectometry (OFDR) with a spatial resolution of better than 2.5 µm. Sweeping the incident laser wavelength by 120 nm, the reflections and losses of wire waveguides, widened waveguides, and optical switches on the chip were individually revealed. The slow-light grating (SLG) beam scanner, which has a limited working wavelength range, was evaluated with a spatial resolution of >10 µm by narrowing the wavelength sweep range. Consequently, a strong reflection was observed at the transition between the wire waveguide and the SLG, which can be a noise source in the FMCW LiDAR. Additionally, this study showed that the OFDR can be an important analysis tool for Si photonics integrated circuits. To our knowledge, this is the first demonstration, showing that the OFDR can be an important analysis tool for Si photonic integrated circuits.

Ultra-narrow, highly efficient power splitters and waveguides that exploit the TE01 Mie-resonant bandgap

In this paper, ultra-narrow and highly-efficient straight and Ω-shaped waveguides, and Y-shaped and T-shaped optical power splitters composed of two rows of two-dimensional germanium rods in air are designed and simulated. The position-disordering effect on the waveguides is considered. Finite-difference time-domain numerical simulation results for two rows of straight and Ω-shaped waveguides with no position disordering at the normalized frequency of a λ=0.327 show optical transmission of 90%, and two rows of Y-shaped and T-shaped power splitters with no position disordering have transmissions >46% for each output branch at the normalized frequency of a λ=0.327. Also, the straight and Ω-shaped waveguides with four rows of germanium rods tolerated position disordering of η = 10%. The proposed ultra-narrow waveguides and power splitters are vital components in high-density and all-dielectric optical integrated circuits.

Space-time-domain observation of high-speed optical beam scanning in a thermo-optic Si photonic crystal slow-light beam scanner

We developed a thermo-optically controlled nonmechanical optical beam scanner using a Si photonic crystal slow-light waveguide with a diffraction grating to achieve on-chip light detection and ranging (LIDAR). This Letter applies pre-emphasis signals to the thermo-optic control, and the cutoff frequency increases to 500 kHz. Observing the beam scanning in the space-time domain showed that the turn-on and turn-off times of the scanner for a rectangular drive voltage were 10 µs and reduced to 2.7 µs when the pre-emphasis signals were optimized. This new, to the best of our knowledge, result enables a frame rate of 29 fps for 12,800 resolution points in LIDAR.

Particle swarm optimization of silicon photonic crystal waveguide transition

Slow light generated through silicon (Si) photonic crystal waveguides (PCWs) is useful for improving the performance of Si photonic devices. However, the accumulation of coupling loss between a PCW and Si optical wiring waveguides is a problem when slow-light devices are connected in a series in a photonic integrated circuit. Previously, we reported a tapered transition structure between these waveguides and observed a coupling loss of 0.46 dB per transition. This Letter employed particle swarm optimization to engineer the arrangement of photonic crystal holes to reduce loss and succeeded in demonstrating theoretical loss value of 0.12 dB on average in the wavelength range of 1540-1560 nm and an experimental one of 0.21 dB. Crucially, this structure enhances the versatility of slow light.

Two-dimensional beam-steering device using a doubly periodic Si photonic-crystal waveguide

We demonstrate a nonmechanical, on-chip optical beam-steering device using a photonic-crystal waveguide with a doubly periodic structure that repeats the increase and decrease of the hole diameter. We fabricated the device using a complementary metal-oxide-semiconductor process. We obtained a beam-deflection angle of 24° in the longitudinal direction, while maintaining a divergence angle of 0.3°. Four such waveguides were integrated, and one was selected by a Mach-Zehnder optical switch. We obtained lateral beam steering by placing a cylindrical lens above these waveguides. By combining the lateral and longitudinal beam steering, we were able to scan the collimated beam in two dimensions, with 80 × 4 resolution points.