Ultrasensitive refractometer based on helical long-period fiber grating near the dispersion turning point

Solid rocket motor propellant health monitoring based on oxide-doped curved long-period fiber grating

A kind of curved long-period fiber grating(CLPFG) engraved by CO2 laser based on oxide-doped fiber was designed to monitor the structural integrity of propellant. The mechanical damage characteristics of the propellant were analyzed. The sensor model is constructed and the refractive index modulation characteristics of the CLPFG are analyzed. The strain coupling characteristics and the strain transfer efficiency of the interface between the CLPFG and the propellant are clarified. Propellant modules with implanted CLPFG were fabricated. The novel grating sensor has been effectively coated and structurally packaged. Conducted experiments on strain and temperature of propellant modules. The large strain measurement of propellant from 0 με to 24000 με is realized. Solved the thorny problem of large strain measurement for propellants. In addition, the temperature discrimination measurement in the temperature range of 30 ℃ to 250 ℃ can be realized. Sensor exhibit extremely high stability characteristics and has good compatibility with propellants. The sensor implantation and extraction structure has been designed to improve the survival rate of the sensor inside the solid rocket motors (SRM). Sensors can accurately measure the mechanical and thermal state parameters of propellants, providing effective data support for the health management of SRM.

Temperature-insensitive high-sensitivity refractive index sensor based on a thinned helical fiber grating with an intermediate period

A temperature-insensitive high-sensitivity refractive index sensor is proposed and experimentally demonstrated, which is based on utilization of a thinned helical fiber grating but with an intermediate period (THFGIP). Attributed to the reduced diameter and an intermediate period of the grating, the proposed sensor has a high surrounding refractive-index (SRI) sensitivity and a low temperature sensitivity. The average SRI sensitivity of the proposed sensor is up to 829.9 nm/RIU in the range of 1.3410-1.4480 RIU. Moreover, unlike the traditional sensitivity-enhancement method by increasing the waveguide dispersion factor, here the waveguide dispersion factor at the resonant wavelength was decreased by reducing the diameter of the fiber grating and as a result, the crosstalk effect due to the temperature change can be further suppressed. The proposed temperature-insensitive SRI sensor has the superiorities of simple structure, ease fabrication, and low cost, which could be found more potential applications in the SRI sensing fields.

Fiber laser cascaded with an MZ interferometer for simultaneous measurement of temperature and refractive index

A fiber laser with strong spontaneous emission and high signal-to-noise ratio is proposed and experimentally demonstrated for simultaneous measurement of temperature and refractive index (RI). By cascading a single MZ interferometer, the power and the emission spectrum of the fiber laser are modulated by surrounding temperature and RI. The dual parameters are determined from the measured power change and interference dip shift. A temperature sensitivity of 0.146 dB/°C (-0.06n m/∘ C) in the range from 20°C to 90°C at an RI of 1.3910 and an RI sensitivity of -156.07d B/R I U (153.70 nm/RIU) in the range from 1.3333 to 1.3910 at 20°C are achieved.

Fabrication of High-Sensitivity Optical Fiber Sensor by an Improved Arc-Discharge Heating System

We proposed a high-sensitivity optical fiber sensor based on a dual-resonance helical long-period fiber grating (HLPG). The grating is fabricated in a single-mode fiber (SMF) by using an improved arc-discharge heating system. The transmission spectra and the dual-resonance characteristics of the SMF-HLPG near the dispersion turning point (DTP) were studied through simulation. In the experiment, a four-electrode arc-discharge heating system was developed. The system can keep the surface temperature of optical fiber relatively constant during the grating preparation process, which shows an advantage in preparing high-quality triple- and single-helix HLPGs. In particular, benefiting from this manufacturing system, the SMF-HLPG operating near the DTP was successfully prepared directly by arc-discharge technology, without secondary processing of the grating. As a typical application example of the proposed SMF-HLPG, physical parameters such as temperature, torsion, curvature and strain can be measured with high sensitivity by monitoring the variation of the wavelength separation in the transmission spectrum. Therefore, the proposed sensor and its fabrication technology have potential application prospects in practical sensing measurement.

Ultrasensitive Optical Fiber Sensors Working at Dispersion Turning Point: Review

Optical fiber sensors working at the dispersion turning point (DTP) have served as promising candidates for various sensing applications due to their ultrahigh sensitivity. In this review, recently developed ultrasensitive fiber sensors at the DTP, including fiber couplers, fiber gratings, and interferometers, are comprehensively analyzed. These three schemes are outlined in terms of operation principles, device structures, and sensing applications. We focus on sensitivity enhancement and optical transducers, we evaluate each sensing scheme based on the DTP principle, and we discuss relevant challenges, aiming to provide some clues for future research.