Longitudinal Miniaturization of Fiber-Packed Capillary Column in High Temperature Gas Chromatography

Optimization of the in-needle extraction device for the direct flow of the liquid sample through the sorbent layer

In-needle extraction was applied for preparation of aqueous samples. This technique was used for direct isolation of analytes from liquid samples which was achieved by forcing the flow of the sample through the sorbent layer: silica or polymer (styrene/divinylbenzene). Specially designed needle was packed with three different sorbents on which the analytes (phenol, p-benzoquinone, 4-chlorophenol, thymol and caffeine) were retained. Acceptable sampling conditions for direct analysis of liquid sample were selected. Experimental data collected from the series of liquid samples analysis made with use of in-needle device showed that the effectiveness of the system depends on various parameters such as breakthrough volume and the sorption capacity, effect of sampling flow rate, solvent effect on elution step, required volume of solvent for elution step. The optimal sampling flow rate was in range of 0.5-2 mL/min, the minimum volume of solvent was at 400 µL level.

Rapid temperature-programmed separation and retention prediction on a novel packed-capillary column in gas chromatography

Novel packed-capillary columns for gas chromatography were developed with a thin-wall stainless-steel capillary of 1.0 mm i.d.; and rapid temperature-programmed separations have been carried out after a basic evaluation concerning the compatibility of these columns to the temperature program. With a numerical integration method, the retention of several test analytes during temperature-programmed elution was successfully estimated. In order to confirm the suitability of the packed-capillary columns to relatively fast temperature programming up to 40 degrees C/min, theoretically predicted retention data were compared with that actually measured. The results suggested a good separation performance of the newly developed packed-capillary columns as a particle-packed column conventionally used. Also, the compatibility to a rapid temperature-programmed operation was quite satisfactory for almost all of the separations currently done in typical analytical laboratories.

Retention behavior on aminoethyl-modified poly(p-phenylene terephthalamide) fiber stationary phases in gas chromatography

Surface derivatization of Kevlar, poly(p-phenylene terephthalamide), fiber has been studied along with the evaluation of the surface characteristics of the chemically-modified fiber as the stationary phase in packed-capillary gas chromatography (GC). Several experimental parameters in the derivatization reaction have been optimized, and the retention behavior of the surface-derivatized fibrous stationary phase has been investigated using various standard solutes, such as alkanes, alcohols and alkylbenzenes. By introducing aminoethyl functional groups onto the surface of the fibrous material, a specific selectivity for polar solutes has been observed.

Single fiber-in-capillary annular column for gas chromatographic separation

A method for preparation of a stationary phase-adjustable column with in-column stationary phase-coated fused-silica fiber annular column was successfully developed. The surface of a 0.12 mm o.d. bare optical fiber was first coated with a stationary phase and then inserted into a fused-silica capillary (non-coated or coated) as an annular column for gas chromatographic study. The optical fiber and capillary were coated with polydimethylsiloxane (SE-30) and polyethylene glycol 20 M (PEG-20 M) as nonpolar and polar stationary phases, respectively. Among the investigated annular and open tubular columns, the PEG-20 M-coated fiber-in-PEG-20 M-coated capillary annular column showed the highest column efficiency with a minimum plate height of 0.35 mm and an optimum gas velocity of 25 cm/s. When a SE-30/PEG-20 M-coated fiber-in-uncoated capillary annular column was applied to separate a 9-component complex mixture, the total analysis time was 5.3 min and the column length was 12 m. By contrast, when a SE-30-coated fiber-in-PEG-20 M-coated capillary annular column was used to separate the same 9-component mixture, the analysis time was reduced to 3.5 min and the column length was shortened by half to 6m. Our results show that the stationary phase-coated fiber-in-stationary phase-coated capillary annular column is a better choice for gas chromatographic separation as it is more efficient and flexible. In addition, the proposed annular column design provides flexibility in using two or even more types of stationary phases to achieve optimal analytical separation.

Understanding and design of existing and future chromatographic support formats

The present contribution reviews the use of alternative support formats as a means to surpass the chromatographic performance of the packed bed of spheres. First, a number of idealized structures are considered to obtain a general insight in how the performance of a chromatographic support depends on its shape and size, using the isocratic peak-capacity generation speed as the main performance indicator. Using this criterion, it is found that the packing density or, equivalently, the external porosity, is the most important of all geometrical shape factors. Depending on whether the sample consists of weakly or strongly retained components, the optimal external porosity can be expected to vary between 60% and a value near 100%. The optimal exploitation of a high external porosity, however, also requires overall shrinkage of the domain size, towards and into the sub-micron range. With the current fabrication technologies, this requirement seems difficult to achieve. In the presence of a lower limit on the characteristic support size, each range of desired plate numbers or peak capacities has its own optimal external porosity, ranging from a very low value (high packing density) for high speed, small peak capacity applications, to very high external porosities (low packing density) for applications requiring a very large peak capacity. Subsequently, the obtained theoretical insights are used to review and discuss the past and current research on alternative support formats. Finally, a number of emerging micro- and nano-fabrication technologies are introduced and their potential for the future production of supports with improved shape and homogeneity is discussed.

Miniaturized sample preparation needle: A versatile design for the rapid analysis of smoking-related compounds in hair and air samples

Miniaturized needle extraction device has been developed as a versatile sample preparation device designed for the rapid and simple analysis of smoking-related compounds in smokers' hair samples and environmental tobacco smoke. Packed with polymeric particle, the resulting particle-packed needle was employed as a miniaturized sample preparation device for the analysis of typical volatile organic compounds in tobacco smoke. Introducing a bundle of polymer-coated filaments as the extraction medium, the needle was further applied as a novel sample preparation device containing simultaneous derivatization/extraction process of volatile aldehydes. Formaldehyde (FA) and acetaldehyde (AA) in smoker's breath during the smoking were successfully derivatized with two derivatization reagents in the polymer-coated fiber-packed needle device followed by the separation and determination in gas chromatography (GC). Smokers' hair samples were also packed into the needle, allowing the direct extraction of nicotine from the hair sample in a conventional GC injector. Optimizing the main experimental parameters for each technique, successful determination of several smoking-related compounds with these needle extraction methods has been demonstrated.

Fiber-packed needle for dynamic extraction of aromatic compounds

A fiber-packed needle was developed as a novel extraction device for gas-chromatographic analysis of trace organic compounds in aqueous samples. In the extraction device, a bundle of the polymer-coated filaments as the sorbent material was longitudinally packed into a specially designed needle. The extraction was made by pumping the aqueous sample solution into the needle extraction device, and the subsequent desorption process was carried out with a flow of desorption solvent through the needle in a heated gas chromatograph injector. The needle device showed an excellent thermal stability for repeated use without any deterioration of extraction performance, and no carryover effect was observed after the optimization of the desorption conditions. Additionally, the extraction efficiency of the fiber-packed needle could be enhanced by optimizing the number of packed filaments. The selectivity for various compounds could be also tuned using an appropriate combination of the fibrous medium and the coating polymer. The relative standard deviation for run to run was from 3.88 to 4.55% (n = 5), and that for needle to needle was 7.21% (n = 3), clearly suggesting a good repeatability of the needle extraction technique developed. Upon successful optimization of the extraction conditions, a rapid extraction of trace organic compounds from an aqueous sample matrix was successfully demonstrated, where each extraction process was completed within 10 min.

Simultaneous derivatization/preconcentration of volatile aldehydes with a miniaturized fiber-packed sample preparation device designed for gas chromatographic analysis

A novel in-needle sample preparation device has been developed for the determination of volatile aldehydes in gaseous samples. The needle device is designed for the gas chromatographic (GC) analysis of aldehydes and ketones commonly found in typical in-house environments. In order to prepare the extraction device, a bundle of polymer-coated filaments was longitudinally packed into a specially designed needle. Derivatization reactions were prompted by 2,4-dinitrophenylhydrazine (NDPH) included in the needle, and so the aldehydes and ketones were derivatized to the corresponding hydrazones and extracted with the extraction needle. A reproducible extraction needle preparation process was established, along with a repeatable derivatization/extraction process that ensures the successful determination of aldehydes. The storage performance of the extraction needle was also evaluated at room temperature for three days. The results demonstrate the successful application of the fiber-packed extraction device to the preparation of a gaseous sample of aldehydes, and the future possibility of applying the extraction device to the analysis of in-house environments.