Influence of miscibility phenomenon on crystalline polymorph transition in poly(vinylidene fluoride)/acrylic rubber/clay nanocomposite hybrid

Hierarchically Structured Porous Piezoelectric Polymer Nanofibers for Energy Harvesting

Hierarchically porous piezoelectric polymer nanofibers are prepared through precise control over the thermodynamics and kinetics of liquid-liquid phase separation of nonsolvent (water) in poly(vinylidene fluoride-trifluoroethylene) (P(VDF-TrFE)) solution. Hierarchy is achieved by fabricating fibers with pores only on the surface of the fiber, or pores only inside the fiber with a closed surface, or pores that are homogeneously distributed in both the volume and surface of the nanofiber. For the fabrication of hierarchically porous nanofibers, guidelines are formulated. A detailed experimental and simulation study of the influence of different porosities on the electrical output of piezoelectric nanogenerators is presented. It is shown that bulk porosity significantly increases the power output of the comprising nanogenerator, whereas surface porosity deteriorates electrical performance. Finite element method simulations attribute the better performance to increased volumetric strain in bulk porous nanofibers.

Nuomici-Inspired Universal Strategy for Boosting Piezoresistive Sensitivity and Elasticity of Polymer Nanocomposite-Based Strain Sensors

Electrically conductive polymer composites (CPCs) are potential alternatives to conventional strain gauges due to their tunable sensitivity and strain ranges. Currently, to achieve very high piezoresistive sensitivity in thermoplastic-based CPCs with Gauge factors G_F above 20 at low tensile strains (ε ≤ 5%) is a big challenge, but critical for structural health monitoring application in infrastructures. Here, inspired by the unique structures of a famous Chinese food, nuomici, we coat carbon nanotubes (CNTs) onto sticky acrylic rubber (AR) granules (ARG) to form nuomici-like CNT@ARG composite granules, which are employed as unique conductive filler to fabricate highly piezoresistive and flexible CPCs based on poly(vinylidene fluoride) (PVDF). This strategy of localizing CNTs densely on the surface of touching rubbery particles resulted in a much more sensitive elastic conductive network built by the CNT@AR composite and showed a big gain effect. The resultant PVDF/CNT@AR nanocomposites (AR content ranging from 0 to 10 wt %) show extremely high piezoresistive sensitivity at low strain, depending on the AR content. In particular, the G_F value of PVDF with 1.5 wt % CNT@10 wt % AR is 41 at 5% strain, which is more than one magnitude higher than that (ca. 3) of traditional PVDF/CNT nanocomposite sensors. Moreover, the elongation at break increases by about 60% with the addition of 1.5 wt CNT@10 wt % AR. This study introduces a universal effective strategy for tailoring the mechanical properties and strain sensitivity of conductive network in CPCs, which is critical for the fabrication of high-performance strain sensors.

A facile method to enhance ferroelectric properties in PVDF nanocomposites

PVDF/Nanoclay physical compatibilization a facile method to enhance ferroelectric properties.

Effects of dynamic vulcanization on the kinetics of isothermal crystallization in a miscible polymeric blend

Is it possible to determine the state of phase separation using the free energy of folding parameter?

Enhanced ferroelectric properties of electrospun poly(vinylidene fluoride) nanofibers by adjusting processing parameters

This contribution investigates the ferroelectric properties and polymorphism evolution of poly(vinylidene fluoride) (PVDF) mats prepared through electrospinning solutions of PVDF in pure N,N-dimethylformamide (DMF) and DMF/acetone mixtures with different weight ratios.

Does dynamic vulcanization induce phase separation?

Immiscible and miscible blends of poly(vinylidene fluoride) (PVDF) and acrylic rubber (ACM) were subjected to dynamic vulcanization to investigate the effect of crosslinking on phase separation. As a result of different processability, mixing torque behavior of miscible and immiscible blends was significantly different from one another. Scanning electron microscopy (SEM) was used to investigate the morphology of the system. After dynamic vulcanization, submicron ACM droplets were observed in the samples near the binodal curve of the system under mixing conditions. Small angle X-ray scattering (SAXS) and differential scanning calorimetry (DSC) analysis were used to investigate the effect of dynamic vulcanization on the lamellar structure of the system. It was shown that for samples near the boundary of phase separation, increasing the crosslink density led to a decrease in the lamellar long period (L) as a sign of increment of crosslink density induced phase decomposition. Effects of shear rate on the final morphology of the system were investigated by changing the mixing temperature and by comparing the results of dynamic vulcanization at one phase and two phase regions.