Numerical Analysis of Fiber/Air-Coupling Field for Annular Jet

Melt-blowing technology is an important method for directly preparing micro-nanofiber materials by drawing polymer melts with high temperature and high velocity air flow. During the drawing process, the melt-blowing fiber not only undergoes a phase change, but also has an extremely complex coupling effect with the drawing airflow. Therefore, in the numerical calculation of the flow field, the existence of melt-blowing fibers is often ignored. In this paper, based on the volume of fluid method, a numerical study of the flexible fiber/air-coupling flow field of an annular melt-blowing die is carried out with the aid of computational fluid dynamics software. The results show that the pressure distribution in the different central symmetry planes of the ring die at the same time was basically the same. However, the velocity distribution may have been different; the velocity on the spinning line varied with time; the pressure changes on the spinning line were small; and velocity fluctuations around the spinning line could cause whiplash of the fibers.

Airflow, Fiber Dynamic Whipping, and Final Fiber Diameter in Flush Sharp-Die Melt Blowing with Different Air-Slot Widths

Melt streams were attenuated into microfibers by high-speed airflow during melt blowing. The present work explored the effect of air-slot width on the fiber diameter and diameter evenness in flush sharp-die melt blowing. The airflow in different die melt blowing was first numerically simulated by the CFD approach. Then, the fiber dynamic whipping was captured by high-speed photography. Finally, a spinning experiment was implemented and the fiber diameters were measured. The result reveals that the sharp die with a larger air-slot width produces fibers with a larger diameter, but the uniformity is obviously better. This study reveals that the air flow, fiber whipping, and final fiber diameter are closely related to each other. The quality control of melt-blown fiber can be carried out by controlling the fiber whipping motion.

Experimental investigation on the three-dimensional flow field from a meltblowing slot die

To investigate the distribution characteristics of the three-dimensional flow field under the slot die, an online measurement of the airflow velocity was performed using a hot wire anemometer. The experimental results show that the air-slot end faces have a great influence on the airflow distribution in its vicinity. Compared with the air velocity in the center area, the velocity below the slot end face is much lower. The distribution characteristics of the three-dimensional flow field under the slot die would cause the fibers at different positions to bear inconsistent air force. The air velocity of the spinning centerline is higher than that around it, which is more conducive to fiber diameter attenuation. The violent fluctuation of the instantaneous velocity of the airflow could easily cause the meltblowing fiber to whip in the area close to the die.

Effect of slot end faces on the three-dimensional airflow field from the melt-blowing die

In order to investigate the effect of the slot ends of the melt-blowing die on the three-dimensional airflow field distribution and the fiber draft, the numerical calculation was carried out. The computational domain of the slot die was established with Gambit, and the flow field was calculated using FLUENT. Compared with the experimental data collected by a hot-wire anemometer, the numerical calculation results are credible. The results show that the slot end face has a certain influence on the three-dimensional flow field distribution under the melt-blowing die. The air velocity and temperature in the center region are quite different from those near the slot-end face. As the distance from the center of the flow field increases, the velocity and temperature on the spinning line begin to decrease. The velocity and temperature distributions of the spinning lines in the central area and nearby areas are almost the same; the temperature and velocity values on the spinning lines near the slot end are the lowest. The distribution characteristics of the three-dimensional airflow field could affect the uniformity of the fiber diameter and the meltblowing products.

Numerical Analysis of Airflow Fields from New Melt-Blowing Dies for Dual-Slot Jets

The melt-blowing process uses high-speed and high-temperature airflow from the die head to draw polymer melt into micron-sized fibers. In this work, to reduce the diameter of the melt-blowing fibers, three new slot dies have been designed based on the common slot die. With computational fluid dynamics technology, the two-dimensional flow fields from these new types of slot dies were numerically calculated. To verify the validity of the calculation, the simulation data was compared with the experimental data. The numerical result shows that the internal flow stabilizers could increase the velocity peak and the pressure peak on the centerline of the flow field and could reduce the reverse velocity, temperature decay, and maximum value of turbulence intensity near the die head. Compared with the common slot die, the slot dies with cuboid bosses could increase the air velocity and temperature on the spinning line in most areas and reduce the air pressure within 1.5 cm below the die. The slot dies with internal flow stabilizers and cuboid bosses have the optimal flow field performance and would be beneficial to the production of thinner fibers.