Explosive Strength of the Knee Extensors: The Influence of Criterion Trial Detection Methodology on Measurement Reproducibility

Assessment of ankle plantar flexor neuromuscular properties: A reliability study

This study aimed to determine test-retest reliability of ankle plantar flexor neuromuscular properties in healthy people to improve understanding of additional measurement and analysis procedures that may be used in outcome assessment. Ten healthy participants (age 29.60 ± 5.36 years) volunteered. Isometric torque_max, rate of torque development (RTD), rate of electromyography rise (RER), impulse, electromechanical delay (EMD), torque steadiness, and torque sensing were obtained during two testing sessions 60 min apart. ICC values ranged from 0.81 to 0.99, indicating good to excellent test-retest reliability. Lower bands of the 95% CIs were all above 0.75 apart from the early phase measures (≤50 ms) derived from explosive torque-time and EMG-time curves, which were between 0.32 and 0.73, indicating poor to moderate reliability. Heteroscedasticity was observed for RTD, impulse, and EMD. LOA as a function of the mean (X̅) for these measures ranged from mean_difference ± 0.25X̅ to ± 0.68X̅. EMD showed excellent reliability (ICC = 0.90; 95% CI [0.63, 0.98]). Torque sensing and torque steadiness showed good reliability (0.81 ≤ ICC ≤ 0.89). Thus, ankle plantar flexor neuromuscular properties showed good to excellent test-retest reliability. However, reliability of measures in the early phase of muscle contraction were consistently lower than the late phase.

Specificity of eccentric hamstring training and the lack of consistency between strength assessments using conventional test devices

Hamstring injuries are endemic, but influences of test-specific training and the application of different test methods on decision making remain elusive. Sport-students were randomised to isokinetic (IG) or Nordic hamstring (NG) exercise or a control group (CG) for six weeks. Training and testing procedures were matched to biomechanical parameters. Hamstring strength (EPT), work, muscle soreness (visual analogue scale (VAS)), biceps femoris (BF_lh) muscle size and architecture were assessed. Anthropometrics and strength parameters did not differ at baseline. Yet, body mass normalised EPT, and work revealed a significant group × time × device effect, with a significant main effect for devices. Experimental conditions triggered meaningful increases in EPT compared to the control group, but the effects were higher when recorded on the training device. Despite significant group × time interactions, normalised average work on the NHD was only higher in the NG compared to CG of the left leg (+ 35%). No effects were found for BF_lh parameters. Hamstrings showed a high training specificity, but adaptations likely remain undetected owing to the low sensitivity of conventional test devices. Moreover, strength increase of ~ 15% does not necessarily have to be reflected in BF_lh parameters.

Familiarization and Reliability of the Isometric Knee Extension Test for Rapid Force Production Assessment

Despite the rising interest in the use of portable force sensors during isometric exercises to inform on neuromuscular performance, the design of practical field-based methods to obtain reliable measures is an ongoing challenge. We aim at identifying the intra-session and test-retest reliability of a rapid, isometric knee extension test to evaluate the maximal voluntary concentric force (MVC), rate of force development (RFD) and impulse following a field-based approach. On two occasions, 14 athletes unfamiliar with the test completed three sets of 2 s ballistic contractions (as fast and hard as possible) with 30 s rest. Raw and filtered data were collected in real time using a portable force sensor. RFD and impulse were highly reliability during “late” phases of the contraction (0–250 ms) since the first session (coefficient of variation (CV) < 9.8%). Earlier phases (0–150 ms) achieved a moderate reliability after one familiarization session (CV < 7.1%). Measures at 0–50 ms did not reach sufficient reliability (CV~14%). MVC was accurately assessed. Dominant limbs were not importantly altered by the familiarization. In opposite, non-dominant limbs showed large variations. New evidence is provided about the positive effects of a single familiarization session to improve the reliability the isometric knee extension test for rapid force production assessment. Coaches and practitioners may benefit of from these findings to conduct practical and reliable assessments of the rapid force production using a portable force sensor and a field-based approach.

Device and method matter: A critical evaluation of eccentric hamstring muscle strength assessments

Equivocal findings exist on isokinetic and Nordic hamstring exercise testing of eccentric hamstring strength capacity. Here, we propose a critical comparison of the mechanical output of hamstring muscles as assessed with either a dynamometer (IKD) or a Nordic hamstring device (NHD). Twenty-five volunteers (26 ± 3 years) took part in a counterbalanced repeated-measures protocol on both devices. Eccentric peak torque, work, angle of peak torque, bilateral strength ratios, and electromyography activity of the biceps femoris long head, semitendinosus and gastrocnemius muscles were assessed. There was a very poor correlation in eccentric peak torque between the devices (r < 0.58), with a systematic and proportional bias toward lower torque values on the IKD (~28%) and a high typical error (~19%) in IKD and NHD measurements comparison. Furthermore, participants performed a higher total eccentric work on IKD, reached peak torques at greater knee extension angles, and showed a greater side-to-side strength difference compared to the Nordic hamstring exercise. Gastrocnemius muscle activity was lower during the Nordic hamstring exercise. Reliability was low for work on NHD and for angle of peak torque and bilateral strength ratios on either device. We conclude that the evaluation of eccentric knee flexor strength depends on the testing conditions and even under standardized procedures, the IKD and NHD measure a different trait. Both tests have limitations in terms of assessing strength differences within an individual, and measurements of the angle of peak torque or side-to-side differences in eccentric knee flexor strength revealed low reliability and should be considered with caution.

Mechanisms to Attenuate Load in the Intact Limb of Transtibial Amputees When Performing a Unilateral Drop Landing

Individuals with unilateral transtibial amputations experience greater work demand and loading on the intact limb compared with the prosthetic limb, placing this limb at a greater risk of knee joint degenerative conditions. It is possible that increased loading on the intact side may occur due to strength deficits and joint absorption mechanics. This study investigated the intact limb mechanics utilized to attenuate load, independent of prosthetic limb contributions and requirements for forward progression, which could provide an indication of deficiencies in the intact limb. Amputee and healthy control participants completed 3 unilateral drop landings from a 30-cm drop height. Joint angles at touchdown; range of motion; coupling angles; peak powers; and negative work of the ankle, knee, and hip were extracted together with isometric quadriceps strength measures. No significant differences were found in the load or movement mechanics (P ≥ .31, g ≤ 0.42), despite deficits in isometric maximum (20%) and explosive (25%) strength (P ≤ .13, g ≥ 0.61) in the intact limb. These results demonstrate that, when the influence from the prosthetic limb and task demand are absent, and despite deficits in strength, the intact limb adopts joint mechanics similar to able-bodied controls to attenuate limb loading.