Optimization by Box-Behnken design for environmental contaminants removal using magnetic nanocomposite

In this study, a CoO-Fe2O3/SiO2/TiO2 (CIST) nanocomposite was synthesized and utilized as an adsorbent to remove methylene blue (MB), malachite green (MG), and copper (Cu) from aqueous environments. The synthesized nanocomposite was characterized using field emission scanning electron microscopy (FE-SEM), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and X-ray diffraction (XRD). Input parameters included pH (3-10), contact time (10-30 min), adsorbent amount (0.01-0.03 g), and pollutant concentration (20-60 mg L-1). The effects of these parameters on the removal process efficiency were modeled and optimized using the response surface methodology (RSM) based on the Box-Behnken design (BBD). The RSM-BBD method demonstrated the capability to develop a second-degree polynomial model with high validity (R2 ˃ 0.99) for the removal process. The optimization results using the RSM-BBD method revealed a removal efficiency of 98.01%, 93.06%, and 88.26% for MB, MG, and Cu, respectively, under optimal conditions. These conditions were a pH of 6, contact time of 10 min, adsorbent amount of 0.025 g, and concentration of 20 mg L-1. The synthesized adsorbent was recovered through five consecutive adsorption-desorption cycles using hydrochloric acid. The results showed an approximately 12% reduction from the first to the seventh cycle. Also, MB, MG, and Cu removal from real water samples in optimal conditions was achieved in the range of 81.69-98.18%. This study demonstrates the potential use of CIST nanocomposite as an accessible and reusable option for removing MB, MG, and Cu pollutants from aquatic environments.

Adsorptive removal of heavy metals from wastewater using Cobalt-diphenylamine (Co-DPA) complex

Heavy metals like Cadmium, Lead, and Chromium are the pollutants emitted into the environment through industrial development. In this work, a new diphenylamine coordinated cobalt complex (Co-DPA) has been synthesized and tested for its efficiency in removing heavy metals from wastewater, and its adsorption capacity was investigated. The effectiveness of heavy metals removal by Co-DPA was evaluated by adjusting the adsorption parameters, such as adsorbent dose, pH, initial metals concentration, and adsorption period. Heavy metal concentrations in real sample were 0.267, 0.075, and 0.125 mg/L for Cd2+, Pb2+, and Cr3+ before using as-synthesized Co-DPA to treat wastewater. After being treated with synthesized Co-DPA the concentration of heavy metals was reduced to 0.0129, 0.00028, 0.00054 mg/L for Cd2+, Pb2+, and Cr3+, respectively, in 80 min. The removal efficiency was 95.6%, 99.5%, and 99.5% for the respective metals. The adsorption process fitted satisfactorily with Freundlich isotherm with R2(0.999, 0.997, 0.995) for Cd2+, Pb2+, and Cr3+, respectively. The kinetic data obeyed the pseudo-second order for Cd2+ and Cr2+ and the pseudo-first order for Pb2+. Based on the results obtained within the framework of this study, it is concluded that the as-synthesized Co-DPA is a good adsorbent to eliminate heavy metal ions like Cd2+, Pb2+, and Cr3+from wastewater solution. In general, Co-DPA is a promising new material for the removal of heavy metal ions from water.

Enhanced degradation of Rhodamine B dye by Fenton/peracetic acid and photo-Fenton/peracetic acid processes

In this research, the efficiency of advanced oxidation processes (AOPs) including Fenton−Peracetic Acid (PAA) and photo-Fenton− PAA in the removal of the Rodamine B (RhB) dye from aqueous solutions were studied. Investigating the effect of operating parameters such as pH (3–9), contact time (2–30 min), PAA concentration (10–80 mg/L), FeCl3.7H2O concentration (10–100 mg/L), and dye concentration (25–500 mg/L) on the performance of AOPs in removal of RhB was considered. The results showed that by decreasing pH and dye concentration, RhB removal efficiency increased. The optimal conditions for removal of RhB using Fenton− PAA process were determined to be as follows: dye concentration = 50 mg/L, pH = 3, PAA concentration = 50 mg/L, contact time = 10 min, and FeCl3 = 50 mg/L; in these conditions, removal efficiency of the RhB was 99.9%. In contrast, the photo-Fenton− PAA process was able to remove this amount of dye in just 5 min. The high performance of the system in a short time is attributed to the synergistic effect of the photo-Fenton− PAA process in the presence of UV. Finally, RhB dye was completely degraded by the photo-Fenton− PAA process and converted into CO2 and H2O products. In general, the photo-Fenton− PAA process compared to other methods can be used as a suitable and reliable method for the treatment of effluents of the dyeing industry and discharge them to the environment.