Physical and Functional Properties of Powders Obtained during Spray Drying of Cyani flos Extracts

Edible flowers are a potential source of bioactive ingredients and are also an area of scientific research. Particularly noteworthy are Cyani flos, which have a wide range of uses in herbal medicine. The below study aimed to investigate the influence of selected soluble fiber fractions on the selected properties of physical and biochemical powders obtained during spray drying a water extract of Cyani flos. The drying efficiency for the obtained powders was over 60%. The obtained powders were characterized by low moisture content (≤4.99%) and water activity (≤0.22). The increase in the addition of pectin by the amount of 2-8% in the wall material resulted in a decrease in hygroscopicity, water solubility, and protection of flavonoids and anthocyanins both before and after digestion in the tested powders in comparison to the sample with only inulin as a carrier. Additionally, it was noted that all samples were characterized by high bioaccessibility when determining antioxidant properties and xanthine oxidase inhibition.

Ultrasound affects physical and chemical properties of Jerusalem artichoke and chicory inulin

Jerusalem artichoke (Helianthus tuberosus L.) and Chicory (Cichorium intybus L.) have a heterogeneous collection of fructose polymers, known as inulin. This study was aimed to explore the effects of ultrasound (US) and autoclave (AC) on inulin physico-chemical properties as well as investigate structural characterizations and relationships with inulin physico-chemical properties. More specifically, Jerusalem artichoke powder (JA, 69.99% inulin in dry basis), purified inulin from Jerusalem artichoke (PJAI) and chicory inulin (CI) were studied to determine the effects of both treatments on reducing sugar contents, degree of polymerization (DP), water-holding capacity (WHC) and particle size. US (90 W, 20 KHZ) treatments had increased reducing sugar content up to 12.27% for PJAI, 10.86% for JA powder and 2.18% for CI. HPLC analysis showed that the DP of inulin decreased for PJAI after 2 min US treatment. WHC analysis showed that both treatments did not have significant effects (p > .05) on WHC for JA powder. This study suggests that US can be a preferable treatment for reducing the DP of inulin from JA for designing variety of food formulations. PRACTICAL APPLICATIONS: Ultrasound treatments could result in more inulin breaking down into reducing sugars, and in the decrease of inulin DP. This research suggested that the DP of inulin might be a very important factor in ultrasound treatment for their affect in the absorption of energy from ultrasound. Therefore, ultrasound can be a desirable treatment for changing the degree of polymerization of inulin from JA for designing different food products. Future studies need to investigate the relationship between the viscosity of inulin solution and the de-polymerization of inulin caused by ultrasound treatment.

Encapsulation of Active Ingredients in Food Industry by Spray-Drying and Nano Spray-Drying Technologies

Since its invention in 1872 by Samuel Percy, the spray drying of food products has been widely used, whether in products consumed by babies in milk formulations, powdered sweets and cocoa soluble in milk for children, or food supplements rich in proteins, vitamins, and minerals for adults. All of these products were first formulated in solution and then converted into powders to facilitate the transport and preservation of the properties during storage. In recent years, novel technologies such as nano spray drying have emerged for the development of food formulations with high-cost active ingredients. The aim of the present work is to present a review of the literature reported in the last 10 years related to these technologies. The basis of the spray-drying technologies i.e., conventional and nano, are described and compared, emphasizing the instrumental processing conditions for achieving a desired product. Examples of some unwanted reactions presented during the encapsulation of active ingredients are provided.

Influence of the Physical State of Spray-Dried Flavonoid-Inulin Microparticles on Oxidative Stability of Lipid Matrices

The effect of the physical state of flavonoid-inulin microparticles (semi-crystalline/amorphous) on the oxidative stability of lipid matrices was studied. Epicatechin (E) and quercetin (Q) microparticles with inulin were formulated at two infeed temperatures (15 °C and 90 °C) by spray drying. X-ray diffraction analyses showed that flavonoid-inulin microparticles obtained at feed temperature of 15 °C were semi-crystalline (E-In-15, 61.2% and Q-In-15, 60%), whereas those at 90 °C were amorphous (Q-In-90, 1.73 and Q-In-90 2.30%). Semi-crystalline state of flavonoid-inulin microparticles enhanced the EE (68.8 and 67.8% for E and Q, respectively) compared to amorphous state (41.6 and 51.1% for E and Q, respectively). However, amorphous Q-microparticles showed the highest antioxidant activity both in methyl linoleate and sunflower oil, increasing the induction period and decreasing the polar compounds and polymer triglyceride formation during long-term oxidation study. Therefore, the physical state of spray-dried flavonoid-inulin microparticles may determine their antioxidant activity in lipid matrices.

Evaluation of the Spray Drying Conditions of Blueberry Juice-Maltodextrin on the Yield, Content, and Retention of Quercetin 3-d-Galactoside

The influence of the processing conditions during the spray drying of mixtures of blueberry juice (BJ) and maltodextrin (MX) was determined quantitatively by the analysis of variance (ANOVA), and qualitatively by the surface response plots (SRP). The effect of two independent variables (inlet temperature, and MX concentration), and one categorical variable (type of MX), was determined on the yield (Y), content (Q), and retention (R) of the antioxidant quercetin 3-d-galactoside. From the ANOVA results, the concentration was the main variable affecting Y and Q, while temperature had a negligible effect, and the low molecular weight MXs exhibited a better response. The physicochemical characterization showed that the powder appearance and microstructure remained unaffected, but size and morphology of the particles varied with the processing conditions. This study established the optimal processing conditions for the spray drying of BJ-MX, and the application limits of the MXs based on the molecular weight distribution.