Ultrasonic supported dye removal by a novel biomass

Sumac Leaves (Rhus Coriaria L), were used as a possible adsorbent of Basic Blue 3 (BB3) removal. The main affecting parameters on adsorption such as concentration, pH and temperature were investigated. Adsorption equilibrium was reached in 30 min. The ultrasonic effect was also enhanced the dyestuff removal. Adsorption capacity was rised from 0.566 to 1.826 mg/g, as rising the concentration from 4 μg/mL to 10 μg/mL. Several isotherm models including Langmuir, Freundlich and Temkin were applied for explaining the adsorption mechanism. Temkin and Langmuir isotherm models describe the system well. Pseudo first order, pseudo second order and intra particle kinetics were evaluated. Pseudo second order diffusion model supports the adsoprption and also intra particle diffusion plays an important role for BB3 removal. Thermodynamics of the adsorption were commented. −2219.5 J/mol of Gibbs energy showed us a spontaneous and physical adsorption.

Ionizing radiation based advanced oxidation process for reactive orange 122 dye degradation and kinetics studies

In the current study, the degradation of reactive orange 122 (RO 122) dye was carried out under UV and gamma irradiation in presence of H2O2. The effect of variables such as UV exposure time, gamma-ray absorbed dose, initial concentration of dye and oxidant dose were investigated. The removal of 64.10, 58.84 and 55.46 (%) was observed for 50, 100 and 150 (mg/L) dye concentrations, respectively using UV radiation time of 150 (min). The degradation was enhanced to 80.39, 69.95 and 67.01 (%) when UV radiation was employed in the presence of H2O2 (0.5 mL/L) for above concentrations respectively. The degradation was further improved to 97, 92.54 and 81.32 (%) using 5 kGy absorbed dose along with H2O2 (0.5 mL/L). The reduction in chemical oxygen demand (COD) was 77, 64 and 57 (%) using UV/H2O2 (0.5 mL/L), while 63, 56 and 53 (%) in case of gamma/H2O2 for aforementioned concentrations. The removal efficiency (G-value), dose constants (k), dose indispensable for 50, 90 and 99 (%) degradation (D 0.5, D 0.90, and D 0.99) after the treatment with gamma radiation were determined. The G-value was noted as 0.46–0.0711 for 50–150 mg/L dye concentration for gamma irradiated samples which improved to 0.57–0.1204 for above mentioned concentrations in presence of H2O2. The FTIR analysis showed that all the peaks were disappeared using gamma/H2O2 at 5 kGy absorbed dose except a minor peak of −CO stretching. The degradation mechanism of dye followed pseudo-first-order kinetics. A significant decrease in peak area was observed by the HPLC analysis after treating the dye samples with gamma/H2O2 (0.5 mL/L) at absorbed dose of 5 kGy which has proven the process efficiency for dye degradation.

Green synthesis of iron nanoparticles and photocatalytic activity evaluation for the degradation of methylene blue dye

The present study focuses on iron nanoparticles (Fe NPs) biosynthesis, characterization and photocatalytic activity (PCA) appraisal for methylene blue dye degradation. A green rapid biogenic synthesis route was employed for synthesis of Fe NPs using banana peel extract. The synthesized Fe NPs was characterized by XRD (X-ray diffraction), SEM (scanning electron microscopy) and EDX (energy dispersive X-ray) techniques. These analysis confirmed the synthesis of zero valent Fe NPs with high crystallinity, purity and semi spherical in shape. The photocatalytic activity was assessed under ultra violet irradiation and under optimum conditions, 87% degradation of MB dye was obtained for 72 min of irradiation, which revealed promising catalytic efficiency of the Fe NPs. The result shows that photocatalytic activity of Fe NPs is promising and could possibly be used to treat dyes in industrial effluents and the use of green synthetic protocol is suggested due to its ecofriendly nature.

Size controlled synthesis of silver nanoparticles: a comparison of modified Turkevich and BRUST methods

In the present investigation, silver nanoparticles were synthesized and a comparative analysis was performed of modified Turkevich and BRUST methods. Silver nitrate precursor was reduced by trisodium citrate dihydrate and ascorbic acid was used as a surfactant. Based on Turkevich and BRUST methods, the process variables, i.e., temperature, reducing agent concentration, stirring speed, mode of injecting reducing agent/precursor to large excess volume of either precursor/reducing agent were studied. The size of the particles was preliminarily ascertained by DLS studies and it was found that modified BRUST method yielded silver nanoparticles with average particle size of 25 nm, while modified Turkevich method furnished nanoparticles with average particle size of 15 nm. The silver nanoparticles were characterized by employing the UV/visible, Zeta sizer, scanning electron microscopy (SEM) and energy dispersive microscopy (EDX) techniques. Results revealed that the silver nanoparticles size can be controlled by optimizing the conditions of modified Turkevich and BRUST methods.

Photovoltaic Properties of ZnO Films Co-Doped with Mn and La to Enhance Solar Cell Efficiency

In the present investigation, ZnO films co-doped with Mn and La were synthesized by the sol–gel technique. XRD analysis revealed that ZnO had a hexagonal structure. Mixed hexagonal and cubic phases appeared in ZnO containing Mn (1%) and La (1.5%). The grain size, d-spacing, unit cell, lattice parameters, atomic packing fraction, volume, strain, crystallinity, and bond length of co-doped ZnO films were determined as a function of doped ion contents. Through UV analysis, it was found that pristine ZnO had E_g = 3.5 eV, and it decreased when increasing the doping concentration, reaching the minimum value for the sample with 1% Mn and 1% La. The optical parameters of the films, such as absorption, transmittance, dielectric constants, and refractive index, were also analyzed. DSSCs were fabricated using the prepared ZnO films. For pure ZnO film, the values were: efficiency = 0.69%, current density = 2.5 mAcm⁻², and open-circuit voltage = 0.56 V. When ZnO was co-doped with Mn and La, the efficiency increased significantly. DSSCs with a ZnO photoanode co-doped with 1% Mn and 1% La exhibited maximum values of J_sc = 4.28 mAcm⁻², V_oc = 0.6 V, and efficiency = 1.89%, which is 174% better than pristine ZnO-based DSSCs. This material is good for the electrode of perovskite solar cells.

Kinetics of acid blue 40 dye degradation under solar light in the presence of CuO nanoparticles synthesized using Citrullus lanatus seeds extract

In view of eco-benign nature of green synthesis, in the present investigation, the CuO NPs are prepared using Citrullus lanatus seeds extract and photocatalytic degradation efficiency for Acid Blue 40 (AB-40) was evaluated. The CuO NPs were characterized by XRD (X-ray diffraction), SEM (scanning electron microscopy), EDX (energy dispersive X-ray), and FT-IR (Fourier transform infrared) techniques. The synthesized CuO NPs was in face centered monoclinic crystalline form with particle size in 40–60 nm range. The photocatalytic degradation potential of CuO NPs was assessed for acid blue 40 (AB-40) dye degradation and catalyst dose, concentration of dye, radiation exposure time and pH are considered for dye removal. The CuO NPs exhibited auspicious efficiency, an 84.89% dye removal was attained at optimal conditions and dye degradation followed BMG (Behnajady–Modirshahla–Ghanbery) kinetics model. Results revealed CuO NPs synthesized using C. lanatus seeds extract is photoactive catalyst and green route can be employed for CuO NPs fabrication for photocatalytic applications.

Biochar caged zirconium ferrite nanocomposites for the adsorptive removal of Reactive Blue 19 dye in a batch and column reactors and conditions optimizaton

Biochar caged zirconium ferrite (BC-ZrFe2O5) nanocomposites were fabricated and their adsorption capacity for Reactive Blue 19 (RB19) dye was evaluated in a fixed-bed column and batch sorption mode. The adsorption of dye onto BC-ZrFe2O5 NCs followed pseudo-second-order kinetics (R 2 = 0.998) and among isotherms, the experimental data was best fitted to Sips model as compared to Freundlich and Langmuir isotherms models. The influence of flow-rate (3–5 mL min−1), inlet RB19 dye concentration (20–100 mg L−1) and quantity of BC-ZrFe2O5 NCs (0.5–1.5 g) on fixed-bed sorption was elucidated by Box-Behnken experimental design. The saturation times (C t /C o  = 0.95) and breakthrough (C t /C o  = 0.05) were higher at lower flow-rates and higher dose of BC-ZrFe2O5 NCs. The saturation times decreased, but breakthrough was increased with the initial RB19 dye concentration. The treated volume was higher at low sorbent dose and influent concentration. Fractional bed utilization (FBU) increased with RB19 dye concentration and flow rates at low dose of BC-ZrFe2O5 NCs. Yan model was fitted best to breakthrough curves data as compared to Bohart-Adams and Thomas models. Results revealed that BC-ZrFe2O5 nanocomposite has promising adsorption efficiency and could be used for the adsorption of dyes from textile effluents.

State-of-art of silver and gold nanoparticles synthesis routes, characterization and applications: a review

To date, the noble metal-based nanoparticles have been used in every field of life. The Au and Ag nanoparticles (NPs) have been fabricated employing different techniques to tune the properties. In this study, the methodologies developed and adopted for the fabrication of Au and Ag have been discussed, which include physical, chemical and biological routes. The Au and Ag characteristics (morphology, size, shape) along with advantages and disadvantages are discussed. The Au and Ag NPs catalytic and biomedical applications are discussed. For the Ag and Au NPs characterization, SEM (scanning electron microscope), TEM (transmission electron microscope), FTIR (Fourier transform infra-red spectroscopy), XRD (X-rays diffraction) and DLS (dynamic light scattering) techniques are employed. The properties of Au and Ag NPs found dependent to synthesis approach, i.e., the size, shape and morphologies, which showed a promising Catalytic, drug delivery and antimicrobial agent applications. The review is a comprehensive study for the comparison of Au and Ag NPs synthesis, properties and applications in different fields.

Highly photosensitized Mg4 Si6O15 (OH)2·6H2O@guar gum nanofibers for the removal of methylene blue under solar light irradiation

In the present investigation, photosensitized nanofibers (NFs) based on guar gum (GG)/poly(vinyl alcohol) (PVA)/Mg4Si6O15(OH)2·6H2O (SP) (modified by 1, 4-diamminobutane [DAB]) was fabricated by electrospinning approach and same was used for the degradation of dye under solar light irradiation. For electrospinning of NFs, the acceleration voltage, nozzle flow rate and collector distance levels of 19,000 KV, 0.5 mL/h and 3 cm were optimum conditions along with 7% (w/v) blend of GG/PVA (1.4:5.6 wt/wt) and 0.01 g modified Mg4Si6O15(OH)2·6H2O. The exfoliation, intercalation and clay organophilization in GG/PVA/Mg4Si6O15(OH)2·6H2O (GG/PVA/SP) NFs were examined by FTIR analysis. The photocatalytic activity (PCA) of NF was studied under the solar light irradiation for methylene blue (MB) dye degradation. The photosensitized GG/PVA/SP2 (G3) showed promising PCA under visible light and G3 furnished higher degradation of MB dye (99.1%) within 10 min of irradiation. Results revealed that GG/PVA/SP based NFs are highly active under solar light, which can be applied for the treatment of wastewater.

Greener approach to substitute chemical reduction clearing process for fabric dyed with Foron Blue E-BL 150, Foron Rubine RD-GFL and Foron Brilliant Yellow S-6GL using indigenous resources

Fabric dyed with disperse dyes followed a reduction clearing process (RCP)/chemical clearing process (CCP) to remove the unfixed dye from the fabric. In the clearing process, unfixed dyes and chemicals are discharged into streams. To combat this issue, an environment friendly approaches is explored that is a biological clearing using indigenous fungal strains of white-rot fungi (Pleurotus ostreatus and Ganoderma lucidum). In this context, fabrics dyed with three disperse dyes (Foron Blue E-BL 150, Foron Rubine RD-GFL and Foron Brilliant Yellow S-6GL) were considered. The fabric cleared with biological clearing process improved the quality of fabric versus chemically cleared fabric and among the tested strains, G. lucidum showed higher efficiency for color strength improvement. However, no significant difference in tensile and tear strength of all fabric samples was observed. The quality of effluents in clearing reduction process for three dyes was assessed and it was observed that water quality parameters including chemical oxygen demand (COD), total organic carbon (TOC), biological oxygen demand (BOD), total suspended solids (TSS), pH, dissolved oxygen (DO) and total dissolved solids (TDS) improved significantly and results revealed that the biological clearing approach can substitute chemical reduction clearing process for fabric dyed with dyes, which is greener and eco-friendly versus conventional processes to avoid unfixed dyes discharge in to water bodies.

Kinetics and Equilibrium of Radioactive Metal Adsorption onto Sugarcane Bagasse Waste: Comparison of Batch and Column Adsorption Modes

Sugarcane bagasse waste biomass (SBWB) efficacy for the adsorption of Zr(IV) was investigated in batch and column modes. The process variables i.e. pH 1–4 (A), adsorbent dosage 0.0–0.3 g (B), and Zr(IV) ions initial concentration 25–200 mg/L (C) were studied. The experiments were run under central composite design (CCD) and data was analysed by response surface methodology (RSM) methodology. The factor A, B, C, AB interaction and square factor A2, C2 affected the Zr(IV) ions adsorption onto SBWB. The quadratic model fitted well to the adsorption data with high R2 values. The effect of bed height, flow rate and Zr(IV) ions initial concentration was also studied for column mode adsorption and efficiency was evaluated by breakthrough curves as well as Bed Depth Service and Thomas models. Bed height and Zr(IV) ions initial concentration enhanced the adsorption of capacity of Zr(IV) ions, whereas flow rate reduced the column efficiency.

Synthesis of Cu-doped MgO and its enhanced photocatalytic activity for the solar-driven degradation of disperse red F3BS with condition optimization

In the present study, Cu (2–12%) doped MgO was synthesized and characterized by SEM, XRD, EDX, and FTIR spectroscopy. The Cu concentration significantly affected the band gap and particle size, which ranged from 4.63 to 3.78 eV and from 27.2 to 79 nm, respectively. In addition, the photocatalytic activity (PCA) of Cu-doped MgO was monitored by the photocatalytic destruction of disperse red F3BS coralene dye, and four reaction variables such as dye concentration, catalyst dose, hydrogen peroxide concentration, and irradiation time, respectively, were optimized by response surface methodology (RSM). Dye degradation was significantly affected by these process variables, and a degradation rate of up to 93% was achieved under optimized conditions. The wastewater samples were also treated under optimized conditions and water quality variables, i.e., chemical oxygen demand (COD) and biochemical oxygen demand (BOD) were significantly improved after treatment. Cu-doped MgO exhibited excellent PCA under the solar-light exposure for the degradation of disperse red F3BS dye, which can be employed for the treatment of dye-containing effluents.

Synthesis and characterization of magnetically separable La1−x Bi x Cr1−y Fe y O3 and photocatalytic activity evaluation under visible light

A series of Bi and Fe doped La1−x Bi x Cr1−y Fe y O3 (x = 0.00–0.10 and y = 0.02–0.12) perovskites were fabricated through a facile microemulsion method and were characterized by XRD, DC electrical-resistivity, dielectric, VSM, and UV–Visible measurements. Orthorhombic phase of synthesized substituted chromite nanocrystallite was confirmed by powdered XRD analysis with crystallite size in 47.8–32.9 nm range. DC electrical resistivity was observed to increase from 1.70–39.99 × 108 Ω-cm. Dielectric parameters analyzed in frequency range of 20 kHz–20 MHz were decreased, while magnetic parameters were observed to increase with the increase in dopant (Bi+3 and Fe+3) concentration. Whereas coercivity values was low (narrow hysteresis loop), which indicate the soft ferromagnetic of the prepared material materials which are quite useful to employ in storage devices and electronics. Moreover, La1−x Bi x Cr1−y Fe y O3 degraded 90.80% Rhodamine B dye under visible light irradiation within 55 min. The increase in electrical resistivity, while decrease in dielectric parameters was also observed with increase in dopant concentration, ferromagnetic nature and excellent photocatalytic properties make this material suitable for high frequency energy devices, microwave appliances as well as an excellent magnetically separable photocatalyst for the purification of contaminated wastewater.

Chemically modified Quercus dilatata plant leaves for Pb (II), Cd (II), and Cr (VI) ions remediation from aqueous solution

The current investigation deals with the removal of Pb (II), Cd (II), and Cr (VI) ions by using chemically modified Quercus dilatata leaves (CMQDL) treated with nitric acid (HNO3), and calcium chloride (CaCl2). Batch biosorption experiments were performed to determine the optimal conditions of pH, biomass dose, temperature, contact time, and initial metal concentration for the utmost removal of heavy metals from water. The structural morphology and functionalities were explained by SEM and FTIR analysis. The maximum biosorption capacities for remediation of Pb (II), Cd (II), and Cr (VI) ions via CMQDL were 17.54, 20.408, 20.83 mg g−1, respectively at the optimal conditions. The Langmuir and Freundlich isotherm were applied to explore the equilibrium data however Freundlich isotherm model best evaluate the equilibrium data with high regression correlation coefficient (R2) values of 0.985, 0.826, and 0.919 for the elimination of Pb (II) Cd (II), and Cr (VI) ions, respectively. The kinetic study proposed that the remediation operation best obeyed the kinetic pseudo 2nd order model. The calculated thermodynamics functions like change in entropy (ΔS°), change in enthalpy (ΔH°) and Gibbs free energy (ΔG°) revealed that the removal of Pb (II) ions via the CMQDL was viable, exothermic and spontaneous, Cd (II) was endothermic and spontaneous and Cr (VI) was endothermic and non-spontaneous. The current study explored that CMQDL can be used for the remediation of Pb (II), Cd (II), and Cr (VI) ions, respectively.

Preparation, Physical Characterization and Adsorption Properties of Synthesized Co–Ni–Cr Nanocomposites for Highly Effective Removal of Nitrate: Isotherms, Kinetics and Thermodynamic Studies

In the current effort, the Co–Ni–Cr Nanocomposites were synthesized by chemical method and characterized by means of scanning electron micrographs (SEM), X-ray diffraction (XRD), Fourier trans from infra-red (FTIR), and vibration sample magnetization (VSM). In the final step, these nanoparticles were used to study the nitrate removal efficiency from aqueous solution. The effect of important factor including pH, concentration of Nitrate (NO3 −) ion, contact time and nanoparticle dose were studied in order to find the optimum adsorption conditions. A maximum of removal of the nitrate was observed at pH 4, initial concentration of 40 mg L−1, amount of nanoparticle of 0.06 g L−1 and contact time 60 min. The adsorption isotherm values were obtained and analyzed using the Langmuir, Frenudlich, Temkin and Dubinin–Radushkevich equations, the Temkin isotherm being the one that showed the best correlation coefficient (R2 = 0.999). In addition to, the adsorption kinetics studied by the pseudo-first-order, pseudo-second-order, Elovich model, Ritchie and intraparticle diffusion models. The experimental data fitted to pseudo-second-order (R2 = 0.999).

Hetero-structured Iron Molybdate Nanoparticles: Synthesis, Characterization and Photocatalytic Application

This study focuses on the synthesis of iron molybdate [Fe2(MoO4)3] nanoparticles (NPs) using simple co-precipitation process. The catalyst synthesized was characterized by advanced instrumental techniques such as XRD, SEM, EDX, TGA and FTIR, which confirmed the successful synthesis of NPs. Organic compound Rhodamine B (Rh. B) dye was selected for photo-degradation due to its complex structure and carcinogenic nature. Results exhibited that at neutral pH, the synthesized catalyst is highly effective for the degradation of Rh. B. For 20 mg/L initial concentration with an initial pH of 6.7, the degradation efficiency of Rh. B reaches 98  % within 180 min. Furthermore, the solution pH (1 to 11) affects the catalytic activity. This indicates that at neutral and/or alkaline pH, the usage of iron molybdate overwhelms the efficiency of Fenton-like reaction. It has been observed that Fe2(MoO4)3 showed excellent stability as after recycling it for 9 times its performance remained effective. Based on these data, the synthesized catalyst could be conveniently employed for degradation of toxic pollutants.

Sol–Gel Synthesis of Mesoporous Silica–Iron Composite: Kinetics, Equilibrium and Thermodynamics Studies for the Adsorption of Turquoise-Blue X-GB Dye

Mesoporous silica (MPS) and MPS-Fe composite was prepared via sol–gel technique and characterized by BET, FTIR, XRD, SEM and pZc. The MPS and MPS-Fe adsorption efficiencies were evaluated for a cationic dye Turquoise-blue X-GB. The MPS-Fe composite showed pore size and BET values of 9.52 nm and 309 m2/g, respectively. XRD and SEM analysis revealed the amorphous nature and uniform distribution of spherical partciles with average particle size of 50 nm of MPS-Fe composite. The points of zero (pZc) charge found to be 2.3 and 6.3 for MPS and MPS-Fe, respectively. The MPS and MPS-Fe showed promising efficiency for the adsorption of Turquoise-blue X-GB as a function of medium pH, contact time, dye initial concentration and temperature. Among, Freundlich, Langmuir, Harkins–Jura, Temkin, Doubinin–Radushkevich isotherms, the Turquoise-blue X-GB followed Langmuir isothermal model with adsorption capacities of 83.34 mg/g and 74.07 mg/g for MPS and MPS-Fe composite, respectively. Among kinetics models, pseudo second order kinetic model fitted to the dye adsorption with R2 values of 0.998 and 0.988 for MPS and MPS-Fe composite, respectively. The negative values of enthalpy (ΔH) and free energy (ΔG) revealed exothermic and spontaneous adsorption of dye at room temperature. Results revealed that MPS and MPS-Fe composite have promising potential for Turquoise-blue X-GB dye adsorption and could possibly be extended for the adsorption of dyes from textile effluents.

Effect of Hydrothermal Reaction Time on Electrical, Structural and Magnetic Properties of Cobalt Ferrite

Cobalt ferrite was synthesized by hydrothermal route in order to investigate the effect of hydrothermal reaction time on structural, magnetic and dielectric properties. The synthesized cobalt ferrite was characterized by X-ray diffraction, Fourier transform infrared and Vibrating-Sample Magnetometer (VMS). XRD data analysis confirmed the formation of cubic inverse spinel ferrite for complete time series as the high intensity peak corresponds to cubic normal spinel structure. The ionic radii, cation distribution among tetrahedral and octahedral sites, lattice parameters, X-ray density, bond lengths were also investigated cobalt ferrite prepared at different hydrothermal reaction time. The crystallite size was found to be in the range of 11.79–32.78 nm. Tolerance factor was near unity that also confirms the formation of cubic ferrites. VSM studies revealed the magnetic nature of cobalt ferrite. The coercivity (1076.3Oe) was observed for a sample treated for 11 h. The squareness ratio was 0.56 that is close to 0.5 which shows uniaxial anisotropy in cobalt ferrite. Frequency dependent dielectric properties i.e. dielectric constant, AC conductivity, tangent loss and AC resistivity are calculated with the help of Impedance Analyzer. Intrinsic cation vibration of cubic spinel ferrites are confirmed from FTIR analysis in the range of 400–4000 cm−1. In view of enhanced properties, this technique could possibly be used for the synthesis of cobalt ferrite for different applications.

ZnO/UV/H2O2 Based Advanced Oxidation of Disperse Red Dye

In view of promising efficiency of advanced oxidation process, ZnO/UV/H2O2 based advanced oxidation process (AOP) was employed for the degradation of Disperse Red-60 (DR-60) in aqueous medium. The process variables such as concentration of catalysts, reaction time, pH, dye initial concentration and H2O2 dose were evaluated for maximum degradation of dye. The maximum degradation of 97% was achieved at optimum conditions of H2O2 (0.9 mL/L), ZnO (0.6 g/L) at pH 9.0 in 60 min irradiation time. The analysis of treated dye solution revealed the complete degradation under the effect of ZnO/UV/H2O2 treatment. The water quality parameters were also studied of treated and un-treated dye solution and up to 79% COD and 60% BOD reductions were achieved when dye was treated with at optimum conditions. The dissolved oxygen increased up to 85.6% after UV/H2O2/ZnO treatment. The toxicity was also monitored using hemolytic and Ames tests and results revealed that toxicity (cytotoxicity and mutagenicity) was also reduced significantly. In view of promising efficiency of UV/H2O2/ZnO system, it could possibly be used for the treatment of wastewater containing toxic dyes.