Effect of Er: YAG Laser on Microtensile Bond Strength of Bleached Dentin to Composite

Evaluation of the microleakage of class V composite restoration after cavity treatment with Erbium, CO2 lasers, Papain, and Bromelain enzymes

OBJECTVES

Different surface preparation and treatment methods may have dissimilar effects on the microleakage of composite resin. This study was conducted to determine the deproteinizing effect of 10% bromelain enzyme, 10% papain enzyme, CO2 , and erbium-YAG laser in regard to decrease in the microleakage of composite restorations.

MATERIALS AND METHODS

Thirty teeth were selected and 60 class V cavities were prepared on the lingual and buccal sides. They were divided into six groups (n = 10): Group 1, phosphoric acid gel; Group 2, bromelain enzyme 10%; Group 3, papain enzyme 10%; Group 4, mixed papain and bromelain enzymes 10%; Group 5, CO2 laser; and Group 6, erbium-YAG laser. They were stored in basic fuchsine and dye penetration was evaluated. Kruskal-Wallis and Mann-Whitney tests were used for statistical analysis, p < 0.05 RESULTS: In both occlusal and gingival margins, comparison of microleakage between groups 1, 2, 3, 4, and 5 showed no significant differences (p = 1) and group 6 had a significant difference with other groups (p ˂ 0.001).

CONCLUSIONS

Microleakage of composite resin in the dentin surface was not affected significantly using either bromelain or papain 10% enzymes or erbium laser. However, CO2 laser had a negative effect on the enamel and dentin margins and increased the microleakage. Erbium laser showed a better effect than enzymes on microleakage.

An In Vitro Study regarding the Wear of Composite Materials Following the Use of Dental Bleaching Protocols

Composite materials used in dental restorations are considered resistant, long-lasting and aesthetic. As the wear of restorations is an important element in long-term use, the aim of this study was to evaluate the surface condition of nanohybrid and microfilled composite resins, after being subjected to the erosive action of dental bleaching protocols. This paper reflects a comparative study between one nanofilled composite and three microfilled composites used in restorations. For each composite, three sets of samples (under the form of composite discs) were created: a control group, an "office bleach" group with discs bleached with 40% hydrogen peroxide gel, and a "home bleach" group with discs bleached with 16% carbamide peroxide gel. Wear was numerically determined as the trace and the coefficients of friction obtained using a tribometer, the ball-on-disk test method, and two balls: alumina and sapphire. For all composite groups, there were statistically significant differences between the wear corresponding to the control and bleaching groups, for both testing balls. Regarding the composite type, the largest traces were recorded for GC Gradia direct anterior, for all groups, using the alumina ball. In contrast, for the sapphire ball, 3M ESPE Filtek Z550 was characterized by the largest traces. With respect to the friction coefficients, the "office bleach" group recorded the largest values, no matter the composite or the ball type used. The 3M ESPE Valux Plus composite recorded the largest friction coefficients for the alumina ball, and 3M ESPE Filtek Z550 for the sapphire ball. Overall, the "office bleach" group was characterized by higher composite wear, compared to the "home bleach" protocol or control group. Nanofilled composite resins showed superior wear resistance to microfilled resins after undergoing a bleaching protocol.

In vitro attrition wear resistance of four types of paste-like bulk-fill composite resins

Background

Recently, the application of bulk-fill composite resins has increased significantly. Attrition wear and the consequently increased surface roughness of composite resins are among the causes of restoration failure in the posterior teeth. This study aimed to compare the attrition wear and surface roughness of four types of bulk-fill composite resins compared to a conventional composite resin.

Methods

EverX-Posterior, X-tra fil, SonicFill 2, and Filtek Bulk-Fill composites (bulk-fill) and Z250 composite (conventional resin composite) were evaluated. Thirty cylindrical specimens (n = 6) were weighed and monitored for 24 h until their weight was stabilized. The primary surface roughness of the specimens was measured by a profilometer. The specimens were then subjected to attrition wear in a chewing simulator. Next, the specimens were weighed, and the surface roughness was measured again. Data were analyzed by one-way ANOVA and Tukey’s post-hoc test at P < 0.05 significance level.

Results

According to one-way ANOVA, the difference in weight loss was significant among the groups (P = 0.004) but the difference in surface roughness of the groups was not significant after the attrition wear (P > 0.05). Tukey’s post-hoc test showed that the weight loss of bulk-fill composites was not significantly different from that of Z250 conventional composite after the attrition wear (P > 0.05).

Conclusion

Within the limitations of this study, it appears that the tested bulk-fill composite resins are comparable to the conventional composite regarding their attrition wear, increased surface roughness, and weight loss.

Supplementary Information

The online version contains supplementary material available at 10.1186/s12903-022-02393-x.

Effects of remaining dentin thickness on the bond strength of bleached dentin

Background

The bond strength of resin composites to dentin was reported to be related to either the remaining dentin thickness (RDT) or bleaching treatment. However, information is limited regarding the effects of RDT on the bond strength of bleached dentin. The present study aimed to investigate the effects of RDT on the microshear bond strength (μSBS) of resin cement to bleached dentin.

Methods

A total of 120 dentin specimens were prepared and randomly divided into 2 groups: a bleaching group (group B) and a control group (group C). Hydrogen peroxide with a concentration of 35% (Ultradent, USA) was applied on the dentin surface for 2 × 1 d for group B, while no bleaching treatment was performed for group C. After the treatment, the specimens were finished and polished to obtain different RDTs (2, 1, and 0.5 mm) and divided into 3 groups of 20 specimens each. The bonding procedure was performed using Panavia V5 (Kuraray, Japan) with a bonding area of 0.785 mm². For each group, half of the specimens were subjected to 5000 thermal cycles (subgroup T), while the other half did not receive thermocycling (subgroup N) (n = 10). The specimens were then subjected to the μSBS test using a universal testing machine. Data were analyzed by a three-way analysis of variance (α = 0.05). The fracture modes of the specimens were confirmed with a measuring microscope. Representative specimens with different fracture modes were observed with scanning electron microscopy (SEM).

Results

The μSBS values were significantly affected by bleaching treatment (p < 0.001), whereas no significant effect was observed for thermocycling (p = 0.293). In terms of RDT, a significantly different μSBS value was found among the subgroups with different RDTs in group C (p = 0.003). However, the RDT did not significantly affect the μSBS values of bleached dentin in group B (p = 0.779). The μSBS values were significantly lower in group B than in group C (p < 0.001). A higher percentage of adhesive failure was observed in group B than in group C.

Conclusion

Based on the present findings, it can be concluded that the RDT did not affect the bond strength of resin cement to bleached dentin.

Clinical significance

Since RDT did not affect the bond strength of resin cement to bleached dentin, bonding procedures should not be performed immediately after intracoronal bleaching, even if the dentin is planned to be removed due to a tooth preparation process.