Cavity Preparation by Laser in Primary Teeth: Effect of 2 Levels of Energy Output on the Shear Bond Strength of Composite Restoration to Dentin

Evaluation of the bond strengths of restorative materials to primary tooth dentin treated with different pulpotomy techniques

The aim of this study was to investigate the changes of different pulpotomy techniques on the primary tooth dentin and to evaluate the effects of these pulpotomy methods on the shear bond strength of restorative materials to primary tooth dentin. Two hundred and forty dentin specimens were distributed randomly to the study groups as; control, ferric sulphate, Biodentine® , Nd:YAG laser, photobiomodulation, and atmospheric pressure cold plasma (APCP). After the application of pulpotomy methods, samples were again randomly divided to two restorative materials (glass hybrid and composite resin) (n = 20) and shear bond strength (SBS) test was performed. Then, 12 new dentin specimens were prepared for all groups for surface analysis. Surface examination (n = 12) and fracture analyses (n = 240) were carried out with scanning electron microscope (SEM). Statistical significance range was accepted as α <.05 for all data. A statistically significant difference was obtained among all study groups for glass hybrid material as well as composite material (p <.05). While the highest mean SBS value was obtained with Nd:YAG laser (7.58 ± 0.60 MPa), the lowest value was observed with Biodentine® (6.70 ± 0.91 MPa; p = .001) for glass hybrid material. For composite material, the highest mean SBS value was calculated for Nd:YAG laser (13.79 ± 1.24 MPa), while the lowest value was obtained with ferric sulphate (10.17 ± 1.45 MPa; p = .001). Fracture modes were mainly adhesive and mixed type according to SEM analysis. Moreover, morphological changes were observed with SEM on the dentin surfaces of ferric sulphate, Biodentine® and Nd:YAG laser. Within the limitations of this study, Nd:YAG laser increased the shear bond strength values in groups of composite resin. RESEARCH HIGHLIGHTS: In this article, we report the results of the shear bonding strength test of two restorative materials (glass-hybrid vs. composite resin) to primary tooth dentin following the application of five different pulpotomy techniques (ferric sulfate, Biodentine® , Nd:YAG laser, photobiomodulation, and atmospheric pressure cold plasma) were reported. This article will contribute to the literature that there are considerably limited researches concerning the bond strength of glass hybrid to primary dentin and also atmospheric pressure cold plasma in pulpotomies. The SEM examination was performed in two stages in this study; the morphological changes in both treated dentin surfaces and the surfaces of the samples subjected to the shear bond strength test.

Optical changes of human dentin after non-vital bleaching and effect of Er,Cr:YSGG laser on micro-shear bond strength of a self-etch and an etch-and-rinse adhesive system

The aim was to evaluate the optical changes of bleached human dentin and the efficacy of Er,Cr:YSGG laser on micro-shear bond strength (μSBS) of two adhesive systems for immediate and delayed applications. Seventy-two human dentin specimens (1 mm) were obtained. Colour measurements of 30 specimens (control and bleaching groups) were made at baseline, after bleaching and a 7-day delay. Differences at colour (ΔE₀₀), translucency (ΔTP₀₀) and whiteness (ΔWI_D) were calculated by recorded data. Forty-two specimens were used to compare μSBS of a self-etch (Clearfil SE Bond [SE]) and an etch-and-rinse (Prime&Bond NT [PBNT]) adhesive to bleached dentin. Additional to a negative group, six groups were contemplated for each adhesive, considering the time of composite application (immediate, delayed) and whether additional surface treatment by laser (1 W, 2 W) or not. Colour and μSBS data were statistically analysed. For optical analysis, only ΔE₀₀ and ΔWI_D calculated for the difference between baseline and bleaching were found significantly different for control and bleaching groups. Whiteness of bleached specimens was remarkably decreased after a 7-day delay. Despite immediate applications of SE showing lower μSBS than negative control, delayed applications showed no significant differences except that of the 2 W laser etching. For PBNT, laser etching increased μSBS for both of the immediate and delayed applications, and no significant difference was observed from negative control. Related with the preferred adhesive system, Er,Cr:YSGG laser etching can be an alternative for optimal bond strength of immediate restorations, but the clinicians should always keep in mind that perceived colour and whiteness will change by the passing time which can affect the shade match.