Adsorption and kinetic desorption study of 152+154 Eu(III) on multiwall carbon nanotubes from aqueous solution by using chelating resin and XPS methods

Neutron Activation Analysis of Rare Earth Element Extraction from Solution through a Surfactant-Assisted Dispersion of Carbon Nanotubes

We report the preparation of surfactant-assisted carbon nanotube dispersions using gum arabic, Triton X-100, and graphene oxide as dispersing agents for removing rare earth elements in an aqueous solution. The analytical tools, including (a) scanning electron microscopy and (b) neutron activation analysis, were utilized for qualitative and quantitative examinations, respectively. Neutron activation analysis was employed to quantitatively determine the percent of extraction of nuclides onto the carbon structure, while the images produced from the scanning electron microscope allowed the morphological structure of the surfactant-CNT complex to be analyzed. This report tested the effects responsible for nuclide removal onto CNTs, including the adsorbent to target mass ratio, the CNT concentration and manufacturing process, the pH, and the ionic radius. Observable trends in nuclide extraction were found for each parameter change, with the degree of dispersion displaying high dependency.

Development of Highest Value of the Measured Efficiency of Mesoporous Petal Shaped Europium (III) Doped Cobalt Tetroxide@Cupric Oxide Hybrid Nanomaterials for Enhanced Room Temperature Photoluminescence and Fluorescence Decay Properties

In our work, a novel series of europium (III) (Eu3+) (5, 10 and 15 wt %) doped cobalt tetroxide@cupric oxide (Co3O4@CuO) nanomaterials (NMs) were synthesized by facile coprecipitation method. The synthesized NMs were characterized by XRD (X-ray diffraction), FT-IR (Fourier transform infrared), UV (ultraviolet)-visible absorption spectra, XPS (X-ray photoelectron), BET (Brunauer-Emmett-Teller) analytical methods. Crystal structure studies revealed the formation of polycrystalline nature with monoclinic and cubic phase. The morphology studies of Eu3+x:Co3O4@CuO (x = 5, 10 and 15 wt %) showed petal shape nanoparticles (NPs) with agglomeration. Redshift in optical absorption spectra appeared with a significant impact on the optical band gap as Eu3+ concentration increases on Co3O4@CuO bimetallic oxide NMs. The chemical composition and valence state of the elements confirmed from XPS studies detected the presence of Eu, Cu, Co, O and C elements. An increase in the pore size and surface area resulted as the Eu3+ concentration increased on Co3O4@CuO NMs. However, room temperature photoluminescence (RTPL) spectra of Co3O4@CuO bimetallic oxide NMs at two different excitations (λ excitation = 280 nm, 320 nm) showed sharp, strong emission intensities located at near ultraviolet (NUV) region and weak emissions detected at far ultraviolet (FUV) regions of the RTPL spectrum. Further, visible range emission intensities were displayed by Eu3+:Co3O4@CuO (5, 10 and 15 wt %) NMs when exited at 280 nm. The characteristic white light emission peaks in the visible range of the RTPL spectra showed intense blue, green and orange colours. Emission intensity increases with an increase in Eu3+ concentration on Co3O4@CuO bimetallic oxide NMs. The fluorescence (FL) decay spectra of Eu3+ 10wt% and 15 wt%: Co3O4@CuO NMs showed a decay lifetime of 2.54 and 2.31 ns (ns) attributed to the dynamic, ultrafast excitation energy transfer between Eu3+ (dopant) and Co3O4@CuO (host) NMs. It is proposed that enhanced RTPL emission intensity and FL decay behavior of Eu3+x:Co3O4@CuO NMs closely related to the change in the optical band gap, variation in the crystallite size, formation of more number of oxygen vacancies in the crystal structure of hybrid nanomaterials.

Carboxylated carbon nanotubes corked with tetraalkylammonium cations: A concept of nanocarriers in aqueous solutions

An explicit water molecular dynamics simulations were used to probe (6,6) and (9,9) single-walled carbon nanotubes, functionalized with three carboxylate ion groups at each of the two openings, as potential nanocarriers in aqueous solutions. Three tetraalkylammonium cations (i.e., tetraethyl-, tetrapropyl-, and tetrabuthylammonium) were tested as corks to cap the nanotube openings. The variation of the sizes of the nanotubes (diameter) and of the cork cations (bulkiness) allowed us to select the proper corks that fit the nanotube openings best. Smaller tetraalkylammonium ions could easily fit the openings, but since they are less hydrophobic compared to their larger analogues they showed less affinity for the interior of the nanotubes. On the other hand, the hydrophobicity (and thus the affinity for the nanotubes) can be adjusted through the increase of tetraalkylammonium cation size, providing that the cork still fits the opening. Additionally, an external electric field was tested as a means of nanotube uncorking. The field is capable of disjoining corked ions from the functionalized nanotube openings, triggering in this way a potential cargo release stored inside the nanotubes.

Carbon nano tubes functionalized with novel functional group- amido-amine for sorption of actinides

The manuscript presents the results on the sorption of U(VI), Am(III) & Eu(III) from pH medium by a novel amido-amine functionalized multiwalled carbon nanotube (MWCNT). The novel functional group was introduced in the MWCNT by two step processes and characterized by various instrumental techniques like Scanning Electron Microscopy (SEM), Raman and X-ray Photoelectron Spectroscopy (XPS). The sorption process was found to be highly dependent on the pH of the solution with maximum sorption for both 233U, 241Am & 152+154Eu at pH 7.0. Kinetics of sorption was found to be fast with equilibrium reached in ∼15min and the sorption was found to be following pseudo 2nd order kinetics for the radionuclides. The sorption for both 233U and 152+154Eu followed Langmuir sorption model with maximum sorption capacity of 20.66mg/g and 16.1mg/g respectively. This has been explained by DFT calculations which shows that more negative solvation energy of U(VI) compared to Am(III) and Eu(III) and stronger U-MWCNT-AA complex is responsible for higher sorption capacity of U(VI) compared to Am(III) and Eu(III).The synthesized amido-amine functionalized MWCNT is a very promising candidate for removal of actinides and lanthanides from waste water solution with high efficiency.

Diglycolamic acid-functionalized multiwalled carbon nanotubes as a highly efficient sorbent for f-block elements: experimental and theoretical investigations

Diglycolamic acid-functionalized carbon nanotubes were employed for the efficient and selective separation of Pu⁴⁺, PuO₂²⁺ and Am³⁺.

Oxidation state selective sorption behavior of plutonium using N,N-dialkylamide functionalized carbon nanotubes: experimental study and DFT calculation

Selective phase separation of Pu⁴⁺ and PuO₂²⁺ was performed using N,N-dialkylamide functionalized multi-walled carbon nanotubes (AFMWCNTs).

Sorption behaviour of Pu4+ and PuO22+ on amido amine-functionalized carbon nanotubes: experimental and computational study

Amido amine-functionalized multi-walled carbon nanotubes (MWCNT-AA) were used for efficient and selective solid phase separation of plutonium(iv) and plutonium(vi).

Different Interaction Mechanisms of Eu(III) and (243)Am(III) with Carbon Nanotubes Studied by Batch, Spectroscopy Technique and Theoretical Calculation

Herein the sorption of Eu(III) and (243)Am(III) on multiwalled carbon nanotubes (CNTs) are studied, and the results show that Eu(III) and (243)Am(III) could form strong inner-sphere surface complexes on CNT surfaces. However, the sorption of Eu(III) on CNTs is stronger than that of (243)Am(III) on CNTs, suggesting the difference in the interaction mechanisms or properties of Eu(III) and (243)Am(III) with CNTs, which is quite different from the results of Eu(III) and (243)Am(III) interaction on natural clay minerals and oxides. On the basis of the results of density functional theory calculations, the binding energies of Eu(III) on CNTs are much higher than those of (243)Am(III) on CNTs, indicating that Eu(III) could form stronger complexes with the oxygen-containing functional groups of CNTs than (243)Am(III), which is in good agreement with the experimental results of higher sorption capacity of CNTs for Eu(III). The oxygen-containing functional groups contribute significantly to the uptake of Eu(III) and (243)Am(III), and the binding affinity increases in the order of ≡S-OH < ≡S-COOH < ≡S-COO(-). This paper highlights the interaction mechanism of Eu(III) and (243)Am(III) with different oxygen-containing functional groups of CNTs, which plays an important role for the potential application of CNTs in the preconcentration, removal, and separation of trivalent lanthanides and actinides in environmental pollution cleanup.

Nanomaterials and nanotechnologies in nuclear energy chemistry

With the rapid growth of human demands for nuclear energy and in response to the challenges of nuclear energy development, the world’s major nuclear countries have started research and development work on advanced nuclear energy systems in which new materials and new technologies are considered to play important roles. Nanomaterials and nanotechnologies, which have gained extensive attention in recent years, have shown a wide range of application potentials in future nuclear energy system. In this review, the basic research progress in nanomaterials and nanotechnologies for advanced nuclear fuel fabrication, spent nuclear fuel reprocessing, nuclear waste disposal and nuclear environmental remediation is selectively highlighted, with the emphasis on Chinese research achievements. In addition, the challenges and opportunities of nanomaterials and nanotechnologies in future advanced nuclear energy system are also discussed.

The removal of U(VI) from aqueous solution by oxidized multiwalled carbon nanotubes

Multiwalled carbon nanotubes (MWCNTs) have exhibited high sorption capacity for radionuclides due to the unique hollow structure and large surface area. In this study, surface properties of oxidized MWCNTs were characterized by using XRD, SEM, FTIR and potentiometric acid-base titration. The sorption of U(VI) on oxidized MWCNTs as a function of contact time, U(VI) concentration, pH, ionic strength, humic acid/fulvic acid (HA/FA) and carbonate was investigated by using batch technique. The removal of U(VI) by oxidized MWCNTs was strongly dependent on pH and ionic strength. The presence of HA/FA enhanced U(VI) removal on oxidized MWCNTs at low pH while inhibited U(VI) sorption at high pH. The mechanism of U(VI) sorption on oxidized MWCNTs was assumed to be cation exchange/outer-sphere surface complexation in acidic pH and to form precipitation under circum neutral conditions. The oxidized MWCNTs exhibit higher sorption capacity and stronger chemical affinity than pristine MWCNTs.

Chemical and structural characterization of carbon nanotube surfaces

To utilize carbon nanotubes (CNTs) in various commercial and scientific applications, the graphene sheets that comprise CNT surfaces are often modified to tailor properties, such as dispersion. In this article, we provide a critical review of the techniques used to explore the chemical and structural characteristics of CNTs modified by covalent surface modification strategies that involve the direct incorporation of specific elements and inorganic or organic functional groups into the graphene sidewalls. Using examples from the literature, we discuss not only the popular techniques such as TEM, XPS, IR, and Raman spectroscopy but also more specialized techniques such as chemical derivatization, Boehm titrations, EELS, NEXAFS, TPD, and TGA. The chemical or structural information provided by each technique discussed, as well as their strengths and limitations. Particular emphasis is placed on XPS and the application of chemical derivatization in conjunction with XPS to quantify functional groups on CNT surfaces in situations where spectral deconvolution of XPS lineshapes is ambiguous.

Europium adsorption on multiwall carbon nanotube/iron oxide magnetic composite in the presence of polyacrylic acid

This paper examines the interaction between Eu(III) and a multiwall carbon nanotube (MWCNT)/iron oxide magnetic composite in the absence and presence of poly(acrylic acid) (PAA). PAA was used as a surrogate for natural organic matter. The effects of pH, initial Eu(III) concentration, and PAA on Eu(III) adsorption on the magnetic composite were investigated using a batch technique. Percentage adsorption of Eu(III) on the magnetic composite increased with increasing pH and decreased with initial Eu(III) concentration. PAA adsorption on the magnetic composite decreased with increasing pH and was not obviously affected bythe presence of Eu(III). The presence of PAA resulted in strong enhancement of Eu(III) adsorption below pH 4.5. However, above pH 5, an increase in soluble Eu-PAA complexes resulted in a decrease in Eu(III) adsorption on the magnetic composite. With increasing PAA concentrations, maximum adsorption of Eu(III) decreased and the adsorption "edge" shifted toward a lower pH range. Obvious difference of Eu(III)/PAA addition sequences on Eu(III) adsorption was observed above pH 4. The Freundlich model fitted Eu(III) adsorption isotherms very well in the absence and presence of PAA. These results are important for estimating and optimizing the removal of organic and inorganic pollutants by the magnetic composite.

Aqueous suspensions of carbon nanotubes: surface oxidation, colloidal stability and uranium sorption

The objective of this study is to obtain information on the behaviour of carbon nanotubes (CNTs) as potential carriers of pollutants in the case of accidental CNT release to the environment and on the properties of CNTs as a potential adsorbent material in water purification. The effects of acid treatment of CNTs on (i) the surface properties, (ii) the colloidal stability and (iii) heavy metal sorption are investigated, the latter being exemplified by uranium(VI) sorption. There is a pronounced influence of surface treatment on the behaviour of the CNTs in aqueous suspension. Results showed that acid treatment increases the amount of acidic surface groups on the CNTs. Therefore, acid treatment has an increasing effect on the colloidal stability of the CNTs and on their adsorption capacity for U(VI). Another way to stabilise colloids of pristine CNTs in aqueous suspension is the addition of humic acid.

Removal of chromium from aqueous solution by using oxidized multiwalled carbon nanotubes

The batch removal of hexavalent chromium (Cr(VI)) from aqueous solution by using oxidized multiwalled carbon nanotubes (MWCNTs) was studied under ambient conditions. The effect of pH, initial concentration of Cr(VI), MWCNT content, contact time and ionic strength on the removal of Cr(VI) was also investigated. The removal was favored at low pH with maximum removal at pH <2. The adsorption kinetics was modeled by first-order reversible kinetics, pseudo-first-order kinetics, pseudo-second-order kinetics, and intraparticle diffusion models, respectively. The rate constants for all these kinetic models were calculated, and the results indicate that pseudo-second-order kinetics model was well suitable to model the kinetic adsorption of Cr(VI). The removal of chromium mainly depends on the occurrence of redox reaction of adsorbed Cr(VI) on the surface of oxidized MWCNTs to the formation of Cr(III), and subsequent the sorption of Cr(III) on MWCNTs appears as the leading mechanism for chromium uptake to MWCNTs. The presence of Cr(III) and Cr(VI) on oxidized MWCNTs was confirmed by the X-ray photoelectron spectroscopic analysis. The application of Langmuir and Freundlich isotherms are applied to fit the adsorption data of Cr(VI). Equilibrium data were well described by the typical Langmuir adsorption isotherm. Overall, the study demonstrated that MWCNTs can effectively remove Cr(VI) from aqueous solution under a wide range of experimental conditions, without significant Cr(III) release.