Diagnostic Potential of Panoramic Radiography and CBCT in Detecting Implant-Related Ex Vivo Injuries of the Inferior Alveolar Canal Border

Soft tissue simulant materials in X-ray-based imaging in dentomaxillofacial radiology: a scoping review

INTRODUCTION

In in-vitro dental radiographic research, simulation of soft tissue is required to replicate the clinical condition as close as possible. This study aimed to find out which soft tissue simulation material have been studied to use in dentomaxillofacial radiology and showed similarity in radiodensity to the soft tissues of the maxillofacial region.

METHODS

In this scoping review, Web of Science, Embase, Scopus, Google scholar and PubMed databases were searched on April 9, 2023, considering the following PICOS: Population: soft tissue simulants, Intervention: X-ray-based imaging, Comparison: -, Outcome: properties of the soft tissue simulants, Study design: in-vitro studies. Screening, study selection, and data extraction were performed by two independent researchers. A third team member was consulted in the case of disagreement. Quality assessment of the included studies was made using Quality Assessment Tool For In-Vitro Studies (QUIN Tool).

RESULTS

Of the initial 1172 articles retrieved in the database search, 13 studies were included in the review. Seven studies had a low risk of bias. In 8 studies, computed tomography (CT) or cone beam computed tomography (CBCT), in 4 studies intraoral radiography, and in 2 studies panoramic radiography was used (one study has used CT/CBCT and panoramic radiography). The studies varied in the radiographic modality, acquisition parameters, selected outcomes, and gold standard. In the majority of the studies (n = 10, 77%), acrylic resin derivatives were used in the soft tissue simulant formula alone or as a major component. Wax was used in the simulant material in 8 studies (62%). In addition, in 3 studies (23%) ice/water was used as the main simulant.

CONCLUSION

Ballistic gelatin, expanded 2-cm thick polystyrene with or without 1-cm utility wax, and 0.5 cm of acrylic resin were shown to have a radiographic density similar to soft tissue in standardized studies employing CBCT scanning. For intraoral radiographs, using self-polymerizing acrylic resin, utility wax, and wood, as well as a polymethylmethacrylate box filled with water in thicknesses ranging from 4 to 45 mm, provides suitable radiographic contrast. However, for 4 and 8 mm of wax and 4 mm of water, the radiographic contrast is not appropriate. In addition, 13-17 mm wax and 14.5 mm acrylic resin showed acceptable soft tissue densities in intraoral radiography. Further studies using different imaging modalities with standardized conditions and objective metrics are required to confirm the most appropriate soft tissue simulant material for in-vitro dental radiographic research.

Do metal artifact reduction algorithms influence the detection of implant-related injuries to the inferior alveolar canal in CBCT images?

BACKGROUND

The routine application of dental implants for replacing missing teeth has revolutionized restorative and prosthetic dentistry. However, cone beam computed tomography (CBCT) evaluations of structures adjacent to the implants are limited by metal artifacts. There are several methods for reducing metal artifacts, but this remains a challenging task. This study aimed to examine the effectiveness of metal artifact reduction (MAR) algorithms in identifying injuries of implants to the inferior alveolar canal in CBCT images.

METHOD

In this in vitro study, mono-cortical bone windows were created and the inferior alveolar canal was revealed. Using 36 implants, pilot drill and penetration damage of the implant tip into the canal was simulated and compared to the control implants with distance from the canal. CBCT images were evaluated by four experienced observers with and without the MAR algorithm and compared to direct vision as the gold standard. The values of accuracy, sensitivity, and specificity were obtained and compared by receiver operating characteristic (ROC) curve (α = 0.05).

RESULT

The area under the ROC curve values for detection of pilot drill injuries varied between 0.840-0.917 and 0.639-0.854 in the active and inactive MAR conditions, respectively. The increase in ROC area was only significant for one of the observers (P = 0.010). For diagnosing penetrative injuries, the area under the ROC curve values was between 0.990-1.000 and 0.722-1.000 in the active and inactive MAR conditions, respectively. The improvement of ROC curve values in active MAR mode was only significant for one of the observers (P = 0.006).

CONCLUSION

Activation of MAR improved the diagnostic values of CBCT images in detecting both types of implant-related injuries to the inferior alveolar canal. However, for most observers, this increase was not statistically significant.

Finite element analysis of the angle range in trans-inferior alveolar nerve implantation at the mandibular second molar

BACKGROUND

Trans- inferior alveolar nerve (IAN) implantation technique was wildly used while the potential appropriate angle range in which the residual alveolar bone can bear the stress without absorption are currently unclear. This study aimed to evaluate the stress distribution pattern of the interface between bone and implant by finite element analysis (FEA) to determine the appropriate range of the implant tilt angle.

METHODS

Cone beam computed tomography (CBCT) images of 120 patients with missing mandibular second molars and vertical bone height < 9 mm in the edentulous area were selected. The distances from the mandibular nerve canal to the buccal cortex, the lingual cortex and the alveolar ridge crest were measured by using a combination of software. The angular ranges of the buccal-lingual inclination of simulated trans-IAN implants were measured and three-dimensional finite element models were constructed in the mandibular second molar area according to the differences of the inclination angles. A vertical load (200N) was then applied to analyze the biomechanical conditions of the implant-bone interface during median occlusion.

RESULTS

The distance at the second molar from the nerve canal to the buccal cortex, lingual cortex and alveolar crest were 6.861 ± 1.194 mm, 2.843 ± 0.933 mm and 7.944 ± 0.77 mm. Trans-IAN implantation was feasible in 73.33% of patients. The minimum angle and maximum angles of the buccal-lingual inclination of the simulated implant were 19.135 ± 6.721° and 39.282 ± 6.581°. When a vertical static load of 200N was applied, the tensile stress in cortical bone gradually increased with the increase of the implant tilt angle. When the inclination angle reached 30°, the tensile stress (105.9 MPa) exceeded the yield strength (104 MPa) of cortical bone. Compared with the conventional implants, the stress peak value of the vertical ultra-short implant in cortical bone was greater than the stress peak value of the conventional implants at 10°(79.81 MPa) and 20°(82.83 MPa) and was smaller than the stress of the implant at 30°(105.9 MPa) and 40°(107.8 MPa). Therefore, when the bone mass allows, conventional-length implants should be selected whenever possible, and an operative range of the trans-IAN implantation in the mandibular second molar could be retained with an inclination angle of < 30°.

CONCLUSIONS

The mandibular nerve canal at the mandibular second molar was obviously biased to the lingual side, which ensured sufficient bone mass at the buccal side. In most patients with severe mandibular atrophy, it was possible to maintain a safe distance from the nerve canal with conventional-length implants via the trans-IAN implantation technique.