Endograft technology: highlights of the past 10 years

Stent fabric fatigue of grafts supported by Z-stents versus ringed stents: An in vitro buckling test

Stent-grafts externally fitted with a Z-shaped stents were compared to devices fitted with ringed stents in an in vitro oscillating fatigue machine at 200 cycles per minute and a pressure of 360 mmHg for scheduled durations of up to 1 week. The devices fitted with Z-stents showed a considerably lower endurance limit to buckling compared to the controls. The contact between the apexes of adjacent Z-stents resulted in significant damage to the textile scaffolds and polyester fibers due to the sharp angle of the Z-stents. The ringed stents did not cause any fraying in the textile scaffolds.

AAA stent-grafts: past problems and future prospects

Endovascular aneurysm repair (EVAR) has quickly gained popularity for infrarenal abdominal aortic aneurysm repair during the last two decades. The improvement of available EVAR devices is critical for the advancement of patient care in vascular surgery. Problems are still associated with the grafts, many of which can necessitate the conversion of the patient to open repair, or even result in rupture of the aneurysm. This review attempts to address these problems, by highlighting why they occur and what the failings of the currently available stent grafts are, respectively. In addition, the review gives critical appraisal as to the novel methods required for dealing with these problems and identifies the new generation of stent grafts that are being or need to be designed and constructed in order to overcome the issues that are associated with the existing first- and second-generation devices.

Effect of curvature on displacement forces acting on aortic endografts: a 3-dimensional computational analysis

PURPOSE

To determine the effect of curvature on the magnitude and direction of displacement forces acting on aortic endografts in 3-dimensional (3D) computational models.

METHOD

A 3D computer model was constructed based on magnetic resonance angiography data from a patient with an infrarenal aortic aneurysm. Computational fluid dynamics tools were used to simulate realistic flow and pressure conditions of the patient. An aortic endograft was deployed in the model, and the displacement forces acting on the endograft were calculated and expressed in Newtons (N). Additional models were created to determine the effects of reducing endograft curvature, neck angulation, and iliac angulation on displacement forces.

RESULTS

The aortic endograft had a curved configuration as a result of the patient's anatomy, with curvature in the anterolateral direction. Total displacement force acting on the endograft was 5.0 N, with 28% of the force in a downward (caudal) direction and 72% of the force in a sideways (anterolateral) direction. Elimination of endograft curvature (planar graft configuration) reduced total displacement force to 0.8 N, with the largest component of force (70%) acting in the sideways direction. Straightening the aortic neck in the curved endograft configuration reduced the total force acting on the endograft to 4.2 N, with a reduction of the sideways component to 55% of the total force. Straightening the iliac limbs of the endograft reduced the total force acting on the endograft to 2.1 N but increased the sideways component to 91% of the total force.

CONCLUSION

The largest component of the force acting on the aortic endograft is in the sideways direction, with respect to the blood flow, rather than in the downward (caudal) direction as is commonly assumed. Increased curvature of the aortic endograft increases the magnitude of the sideways displacement force. The degree of angulation of the proximal and distal ends of the endograft influence the magnitude and direction of displacement force. These factors may have a significant influence on the propensity of endografts to migrate in vivo.

Endovascular device design in the future: transformation from trial and error to computational design

Endovascular devices have been designed by trial and error, with bench and animal testing followed by human clinical trials to determine whether the devices are safe and effective. Despite remarkable advances over the past 15 years, there are persistent concerns regarding the long-term durability of endovascular devices. This may be due to deficiencies in device design, which has lagged behind other industries in adopting computational methods that are now routinely used to design, develop, and test new aircraft and automobiles. Similar computational design and failure mode simulations that evaluate performance under stress conditions have not been widely applied in the development of endovascular devices. Advances in medical imaging and computational modeling now allow simulation of physiological conditions in patient-specific 3-dimensional vascular models, which can provide a framework to design and test the next generation of endovascular devices. This modeling will allow the prospective design of devices that can withstand the force variations in the cardiovascular system that occur during bending, coughing, and varying degrees of exercise, as well as the extremes encountered during sudden impact in contact sports. Utilization of computational design methodology that takes into consideration the physiology of the cardiovascular system will improve future endovascular devices so that they are safer and more effective and durable.

MRI virtual biopsies: analysis of an explanted endovascular device and perspectives for the future

Information that can be obtained by magnetic resonance imaging (MRI) of explanted endovascular devices must be validated as this method is non-destructive. Histology of such a device together with its encroached tissues can be elegantly performed after polymethymethacrylate (PMMA) embedding, but this approach requires destruction of the specimen. The issue is therefore to determine if the MRI is sufficient to fully validate an explanted device based upon the characterization of an explanted specimen. An AneuRx device deployed percutaneously 25 months earlier in a 75-year-old patient was removed en bloc at autopsy together with the surrounding aneurysmal sac and segments of the upstream and downstream arteries. Macroscopic pictures were taken and a slice of the cross-section was processed for histology after polymethylmethacrylate (PMMA) embedding. For the magnetic resonance imaging investigation, the device was inserted in a Biospec 4.7 T MRI system with a 20 mm diameter birdcage resonator used for both emission and reception. A Spin-Echo (SE) was used to acquire both T1 proton density (PD) and T2 weighted images. A gradient-echo (GE) sampling of a free induction decay (GESFID) was used to generate multiple GE images using a single excitation pulse so that four images at different TE were obtained in the same acquisition. The selected explanted device was outstandingly well-healed compared to most devices harvested from humans. No inflammatory process was observed in contact or at distance of the materials. In MRI T1 images display no specific contrast and were homogeneous in the different tissues. The contrast was improved on proton density weighed images. On the T2 weighed images, the different areas were well identified. The diffusion images displayed in the surrounding B region had the greatest diffusion coefficient and the greatest anisotropy. The MRI analysis of the explanted AneuRx device illustrates the possibilities of this technique to characterize the interaction of the endovascular graft with the surrounding tissues. MRI is a breakthrough to investigate explanted medical devices but it also can be advantageously used in vivo to obtain virtual biopsies, because real biopsies to determine the 3 Bs (biocompatibility, biofunctionality and bioresilience) cannot be carried out as they could obviously initiate infection and degradation of the foreign materials.